Search Documents

By A. H. Mokken

Failed attempts at amalgamation of a gold/osmiridium concentrate, recovered behind pebble mill liners during re-lining, led to the discovery that the gold particles were coated and that nitric acid only could remove the coatings. Following this treatment amalgamation was rapid and resulted in a complete recovery of the gold that otherwise would have been lost in plant residues. Investigations into the nature and formation of the coatings led to the realization that the coatings were impregnations of harder elements, associated with the gold during grinding and driven into the softer gold surface by high pressure, impact and attrition. It was further realized that this phenomenon could be part of gold ore milling, world-wide. With these thoughts in mind the question is asked whether concentration down to micron sizes prior to cyanidation, should not play a greater role in gold recovery.

Jan 1, 1999

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By P.J. Terbrugge

Open pit slope design has conventionally been effected as a bottom-up function utilizing available geotechnical information. This results in a decision criterion based on probability of failure and factor of Safety with a risk assessment being carried out on the proposed design slopes. The design approach recommended reverses the process using fault event tree decision methodology. The consequences of this approach are that acceptable risk criteria have to be determined by mine owners. Slopes are then designed by the technical staff to achieve these corporate goals. Benefits that arise from the process are that the owners take a proactive decision on the risk-benefit relationship allowing the technical staff to optimize the geotechnical exploration programme and design.

Jan 1, 2006

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By J. de Korte, Z. Loubser

"SynopsisThe aim of a blending stockpile is to minimize the natural variation in properties of a material. Two simulation models were written, for coneshell and chevcon stacking, and used to investigate the influence of different stockpile parameters on blending efficiency. The coneshell model is used to show that blending efficiency is highly sensitive to stacked height, with lower output variances observed for higher capacities. Output variance in both models also decreased when the stacker movement increment was decreased. For chevcon stacking, increasing stacker speed significantly increases the blending efficiencies. Increasing the length of the blending tail also reduces output variation, but this parameter would need to be weighed against the accompanying decrease in buffer capacity.IntroductionEven in the most uniform deposit of materials in nature, material properties will vary. The degree of variation can be measured, and usually resembles a normal distribution. The aim of blending and homogenization operations is to minimize the standard deviation of this normal distribution (De Wet, 1994). In general, the reduction in variation will result in a more efficient and cost-effective downstream process. Cement plants need a precise blend of raw materials to ensure desired kiln performance; boilers used in power generation are optimized for fuels of a constant specification; and even though the separation density in a coal washing plant can be adjusted, a constant product quality cannot be produced from highly variable feed (Denny and Harper, 1962). The process efficiency, product quality, and environmental compliance depend on consistency of characteristics in the material fed (Kumral, 2005) Many industries involved in"

Jan 1, 2015

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By H Möller

The purpose of this paper is to give an overview of the corrosion behaviour of steel in seawater. It is shown that the corrosion products (oxy-hydroxides and calcareous deposits) that are formed during corrosion in seawater have a significant effect on the corrosion behaviour of steel. The chemical composition of the steel determines how protective the oxy-hydroxide corrosion product is. The composition of the seawater influences the nature of the calcareous deposits. This needs to be considered when artificial solutions are used to simulate the corrosion behaviour of steel in seawater. A 3.5% NaCl solution is used frequently for this purpose, but because no calcareous deposits can be formed in this solution, erroneous results in terms of corrosion rates are obtained. The more complex ASTM D1141 artificial solution can be used to include the effects of ions other than Na+ and Cl- in synthetic seawaters. The importance of these other ions on the formation of calcareous deposits is discussed. Keywords: Steel, corrosion, seawater, calcareous deposits, oxy-hydroxides

Jan 1, 2006

By C. Erichsen, J. Werfling

ABSTRACT: A three-dimensional elastic constitutive model for rock salt is proposed. This stress strain law takes into account the three phases of creep (transient, steady state and accelerated creep), dilatancy, as well as the failure and post failure behaviour. The model was implemented into a finite element program and validated on the results of laboratory tests and in situ measurements. A good qualitative and quantitative agreement with the test and measurement results is achieved. A stability analysis for an underground repository in rock salt is presented. ZUSAMMENFASSUNG: Es wird ein dreidimensionales elastisch-viskoplastisches Stoffgesetz für Steinsalz vorgestellt. Mit diesem Stoffgesetz können die drei Kriechphasen (primäres, sekundäres und tertiäres Kriechen), Dilatanz sowie das Bruch- und Nachbruchverhalten erfaßt werden. Dieses Modell wurde in ein Rechenprogramm, das auf der Methode der finiten Elemente basiert, implementiert und an Ergebnissen von Laborversuchen und in-situ-Messungen validiert. Die Versuchs- und Meßergebnisse lassen sich mit diesem Stoffgesetz qualitativ und quantitativ gut nachvollziehen. Als Anwendungsbeispiel wird der Standsicherheitsnachweis für eine Untertagedeponie im Steinsalz erläutert. RÉSUMÉ: Cet article présente un modéle constitutive élastique/viscoplastique à trois dimensions pour sel gemme. Ce modéle comprend les trois stade de fluage (fluage primaire, secondaire et tertiaire), la dilatation, le comportement de défaillance et d'après défaillance. Il est implanté dans un programme de calcul aux éléments finis. À l'aide des essais laboratoire et des mésures in situ, le modéle a été validé. Les résultats des essais et des mesures concordent qualitatifs et quantitatifs aux résultats des calculations.

Jan 1, 2003

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By M. Shahabi, M. Kashfi

This paper briefly describes the excavation procedure of a powerhouse, comprising of its incremental excavation, reinforcement measures, and the installed monitoring system. During the first phase of excavation, the data obtained from monitoring of the behavior of Mudstone layers were used to recommend extra support measures. These data are also used to design the support of the powerhouse during its extension phase. In diesen bericht wird die bohrmcthode von kraftwerk ecavation in stupenweise dargestelt, und in die richtung d.sicherung, Mit hilfe von monitoring systeme. Die monitoring in (mudstone) schichten ist an schutz in bohrung entworfen und montiert in diese methode in K.W. fase 1 schutzung das K.W. in erweiterung der K.W. das berte auserwelt worden ist Cet article décrit brièvement le procédé d'excavation d'une centrale électrique, comportant de son excavation incrémental, de mesures de renfort, et du système de surveillance installé. Pendant la première phase de l'excavation, les données obtenues à partir de la surveillance du comportement des couches de schiste ont été utilisées pour recommander des mesures supplémentaires de soutien. Ces données sont également utilisées pour la conception de la soutènement de la centrale électrique pendant sa phase d’extension.

Jan 1, 2003

By N. R. Williams

Black Mountain, a polymetallic base metal mine located in the Northern Cape territory of South Africa has been blessed with high grade economic ore for many years. Now that the Broken Hill orebody is nearing the end of its life, a lower grade orebody (Swartberg) is being exploited to supplement production from Broken Hill. In addition, ore from stopes in the upper levels of the Broken Hill orebody is considerably tarnished (oxidized). As a natural result, the remaining ore contains a higher percentage of magnetite, pyrrhotite and pyrite than in earlier years. Bismuth, cadmium and cobalt also occur in the ore in higher quantities. The life of the mine has been lengthened with the discovery of further deeper-lying ore reserves extending from the Broken Hill orebody suitably called the Deeps section. However, to bridge the gap between development of the new reserve and the exhaustion of the old reserve, these lower grade and tarnished (oxidized) ores have to be treated. The mine has had reasonable success in identifying unfavourable or problematic ore types and stockpiling them separately to blend in small quantities with more favourable ore. Bench and plant scale tests have aided identification of the various ore types and significant improvements in flotation metallurgical results have been seen. Copper, lead and zinc metal occur as sulphides in the ore. The mill consists of a differential and sequential flotation process that extracts copper concentrate, lead concentrate and zinc concentrate respectively with silver metal recovered in the copper and lead concentrates. This paper describes the ore blending strategy employed at the mine to maximize the econo-metallurgical efficiency of the operation.

Jan 1, 2001

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999