Search Documents

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By F. Nakhaei, Z. Pourkarimi

Tailings produced from the iron ore industry present many challenges due to the high economic and environmental impacts involved with their disposal. However, the relative scarcity of high-grade iron ores has driven manufacturers to recover and recycle these valuable tailings (secondary sources). This study aimed at the purification of ultrafine tailings with high sulphur content from an iron ore concentrator via reverse flotation to produce pellet feed fines. A specially designed flotation column featured with a nano bubble generator and a conventional bubble generator were employed to assess the effects of nano bubbles on the desulfurisation performance of iron ore concentrate under different operating conditions. Results obtained from this study indicated that the sulphur content of iron concentrate could be reduced from 1.2% to 0.22% in the presence of nano bubbles. Also, the results showed that use of nano-micro bubbles increased sulphur recovery 20% more, in comparison to micro bubbles. Keywords: Column flotation, iron ore, tailings, slime, nano bubbles, desulphurisation

Jan 1, 2020

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By J. M. Richards

For most of the 20th century optical petrography has been the primary petrological and mineralogical tool used to characterize coal. The development of quantitative SEM-based techniques, e.g. QEMSCAN®, for coal began only about a decade ago. The application of these techniques for coal lagged behind other commodities, but they are currently being developed with the aim to provide ?one complete analysis? for coal. Quantitative SEM-based techniques are supplemented by quantitative X-ray diffraction (XRD). Recent indications are that these more modern techniques cannot replace the ?standard? petrographic and chemical evaluations, but rather complement them where and when required. The great advantage of quantitative SEM-based techniques is that they are very rapid, with the result that large volumes of samples can be processed on a routine basis. This is ideal for coal type identification, since the results can be used in the creation of ?intelligent? composites. This can lead to the more speedy evaluation of coal deposits by reducing the number of samples on which detailed metallurgical and characterization test work is required, without an increase in the overall statistical error of the resource model. Coal petrography, however, remains important for the prediction of the coking characteristics of certain coals and coal products. As a consequence it is therefore important that any coal laboratory be able to produce data with confidence. This requires strict quality control and assurance protocols that adhere to international standards. Keywords coal petrography, coking strength, scanning electron microscopy, QEMSCAN®.

Nov 1, 2013

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By B. A. Dukas

The diamond-drilling machine has for many years been the most important exploration tool In the search for and subsequent evaluation of Witwatersrand-type ore deposits. With a view to increasing the range of services that can be provided and, at the same time, counteracting rising drilling costs, new techniques are continuously being developed. Many of these techniques have equal application in surface and in underground exploration. This paper reviews drilling techniques such as non-coring pilot holes and deep wire-line drilling, as well as the design of core-barrels and drilling bits to cater for the specific nature of the job on hand. Special drilling fluids and aluminium rods to assist in normal drilling operations are also discussed. Special mention is made of a bore hole's natural tendency to deviate in a certain direction. The factors that cause deviation are used to the advantage of controlled drilling techniques.

Jan 1, 1983

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By C. A. Green, M. A. T. Cocquerel, R. T. Gates

"Engineering studies by Selection Trust, Limited, initially in connection with the development of a copper and nickel deposit for Bamangwato Concessions, Limited, and subsequently for several other clients, have required a large number of metallurgical design calculations. The flash smelting process, developed by Outokumpu Oy in Finland, has been selected as the most suitable method for these projects and the computer programs described in this paper have been developed to facilitate the computation.The data required by the programs arc the chemical and mineralogical analyses of the concentrate, gangue and flux materials and the specification of possible fuels. The required grade of furnace matte is set as the main design parameter and the programs calculate detailed heat and material balances for the smelting process."

Jan 1, 2014

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By L. E. Salinas-Farran, S. J. Neethling

Key variables in heap leaching include permeability, mechanical stability and mass transport. All of these properties can be manipulated by agglomerating and curing the ore before stacking it into heaps. The chemical and structural evolution of the agglomerates during curing is key to improving agglomerate properties and, ultimately, heap performance. It is possible to image the internal structure of agglomerates using SEM/EDX (e.g. QEMSCAN or MLA), although these methods are destructive and do not represent the 3D structure of the agglomerates. A non-destructive alternative is to image the agglomerates using X-ray Microtomography (XMT). Not only does this provide 3D information, it also allows the same samples to be repeatedly scanned, allowing the time evolution of the agglomerate structure and chemical composition to be tracked. In this paper we compared the behaviour of ores agglomerated using a combination of sulphuric acid and ferric sulphate with ones in which chloride ions are added to the recipe, since chloride leaching is gaining in popularity as a chemical alternative to bioleaching for sulphide ores. We tracked the curing process beyond the typical time scales to see the impact that this has on both the agglomerate structure and the subsequent leaching behaviour. Keywords: Heap leaching, curing extent impact, leaching kinetics, ferric-chloride leaching

Jan 1, 2020

By N. Mangadoddy, M. Padhi

The simulation of multi-component classification with modified viscosity model is the key focus in the current study. The classification of the ores using hydrocyclone is a renowned process and has a convoluted flow separation phenomenon. The highly turbulent flow inside hydrocyclone depends on the operating and design parameters apart from the feed mixture. Slurry viscosity also plays a dominant role in the classification of solid particles under the centrifugal settling action. A heterogeneous mixture with different components would result in different settling and rheological behaviour of particles’ suspension in the water medium. The newly proposed multi-component viscosity model (Mandakini et al. 2020) is implemented as a user-defined function to define the material property during the CFD study of the mixture rheology inside hydrocyclone classifier. The multiphase and turbulence model is solved using the modified Algebraic Slip Model and Large Eddy Simulation model. A comparison of the predicted component performance curves is evaluated with and without the corrected viscosity model. The density and size effect on the particle phase distribution inside the classifier are compared, where the misplacements of the finer particles are carefully assessed. Validation of the component classification in hydrocyclone with the laboratory experiments found a close agreement with the rheology based CFD data. Keywords: Dual-component, multi-component viscosity model, double-gap rheometer, computational fluid dynamics, high solids concentration

Jan 1, 2020

By A. Brodt, I. Mezhibovsky

The traditional vertical transportation systems deliver both gangue and useful mineral. The extraction of the desired minerals requires the construction of mineral processing and waste management plants, driving production costs, and often creating a negative environmental impact. The proposed technology is an integration of mineral processing within the transportation system. The mined rock is crushed and then loaded into a vertical lifting system filled with heavy media, with an intermediate density between the mineral and the waste rock. Driven by gravity separation, the desired mineral floats to the earth's surface, while the waste sinks. Delivered minerals and sunk waste is extracted from the heavy media and is then regenerated to a dry state. The useful mineral should be suitable for further use, and the waste used for backfilling. Remained residues of the heavy media may be recycled and reused in the vertical transportation system. Trials of the proposed process in a pilot format have confirmed economic and environmental advantages over traditional methods of transportation and mineral processing technologies. Keywords: Gravitational processes of mineral processing, separation in heavy media, vertical transportation to earth's surface by floating up

Jan 1, 2020

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By D. Moradkhani, S. M. Javad Koleini, M. Abdollahy, F. Soltani

"The objective of the study was to determine the type and distribution of rare earth elements (REEs) in the phosphate flotation concentrate from the Esfordi flotation plant in central Iran, in order to understand their leaching behaviour. Samples of the concentrate were prepared and analysed using XRF, XRD, ICP, and EMPA. The Ce, Nd, La, and Y contents were 5608, 2227, 1959, and 679.7 mg/kg, respectively. The main REEbearing minerals in the concentrate are fluorapatite, monazite, and xenotime. Apatite is the chief mineral of the concentrate and the ratio of apatite to monazite is greater than 60. From EMPA analysis, monazite contains a much higher proportion of REEs than apatite, but more than 50% of the REE content of the concentrate is in apatite, as this is the main mineral constituent of the concentrate. During the leaching of REEs in the phosphoric acid production process, more than 99% of the total rare earth values report to the large amounts of phosphogypsum (CaSO4·2H2O) formed during the dissolution reaction. Accordingly, two process options are suggested for treating the Esfordi concentrate. In the first option, the concentrate is treated with 98% H2SO4 at 200–300°C. After digestion and water leaching, phosphorus and REEs are precipitated out of solution. In the second option, the concentrate is treated in a pre-leach stage. The process residue from the pre-leach stage is then subjected to acid digestion at elevated temperature for phosphoric acid production.IntroductionThe rare earth elements (REEs) comprise a set of 17 chemical elements in the periodic table, specifically the 15 lanthanides plus scandium and yttrium. REEs and alloys that contain them are used in devices such as computer memory, rechargeable batteries, cell phones, catalytic converters, magnets, fluorescent lighting, and many more (Krishnamurthy and Gupta, 2004). China supplies about 94% of the REE demand, with the remaining 6% coming from Russia and Estonia, the USA, India, Malaysia, and Brazil (Zhanheng, 2011). Increased industrial development in China has prompted the Chinese government to limit annual export quotas to approximately 35 kt of rare earth oxides (REOs), while non-Chinese annual demand is expected to reach 80 kt by the year 2015. This constriction of supply is being met by the development of many new rare earth mining projects, each of which has its own unique mining and processing challenges (Jordens, Cheng, and Waters, 2013). One of these projects is the Esfordi phosphate project, which is located in Yazd Province in central Iran. The concentrate from the Esfordi flotation plant contains 1.2–1.5% REEs."

Jan 1, 2017

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By K. Kasas, J Kermeci, S. Vujic, S. Secei, P. Kermeci

On the ‘Majdan III’ open pit mine, supplying with brick clays the production plants of the industry of building material ‘Potisje-Kanjiza’ from Kanjiza, a modern ECS (excavator-conveyor-spreader) complex was built, integrating four bucket excavators, six conveyors and one spreader into a whole. This complex connects the mineral-exploitation unit with the final brick-products plant of the company. Monitoring and management of the ECS complex is carried out by modern computer-supported information-management system (IMS) implementing most modern measuring-regulation, computer and GPS equipment. It was concluded that, for safety reasons, the functions of the IMS should be developed by a component of active visual monitoring of the ECS complex. For this purpose, the task of making a project on intelligent system for visual monitoring of the ECS complex was entrusted to the Department of Computer Application at the Faculty of Mining and Geology, University of Belgrade. This paper gives a review of basic project solutions. Keywords: Automation, process management, information management technology, visual system, intelligent systems, TV monitoring, surface exploitation, clay, Majdan III, Potisje-Kanjiza.

Jan 1, 2003

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020