Search Documents

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By Sylvie Poirier

Researchers at Natural Resources Canada (NRCan) CANMET Mining and Mineral Sciences Laboratories (CANMET-MMSL) and Mining Technologies International (MTI) have designed and built a hybrid diesel-electric mining loader that is the first of its kind to be developed for underground mines. Diesel equipment is popular because of its mobility and most mining operations are reluctant to replace it with tethered electrical equipment despite the obvious elimination of diesel contaminants and significantly lower heat generation (? 35% of an equivalent diesel). However, a diesel-electric vehicle, being currently evaluated by CANMET-MMSL, could be beneficial. In this unit, a constant load diesel generator feeds batteries which, in turn, powers electrical motors that drive the equipment. In a hybrid diesel-electric unit, the constant load diesel generator can be optimized for minimal emissions and hence lower dilution air requirements. This paper will present the project status and the anticipated benefits for mining operations through the application of this technology.

Jan 1, 2008

By D. Sager

Middleburg Ferrochrome (MFC), a company in Samancor Chrome, commissioned a new ferrochrome smelter in March 2009. This is a 60 MW DC-arc furnace with a DC power supply for the smelting of Transvaal chromite ore fines. With the benefit of 12 years' experience with this technology while operating a 44 MW DC-arc furnace, MFC mitigated all known challenges and considered up-scaling risk in the new plant, which had a rapid ramp-up to full power in 02 of 2009. Good operating practices, as made possible by robust equipment selection, including a thyristor rectifier set of proven technology, and operation with optimal slag chemistry, leads to a safe and effective plant operation. With the optimized furnace design and a correctly sized power conditioning system, using only standard (static) harmonic filters and a correctly sized smoothing reactor, the arc furnace is not a 'dirty load' for the utility, staying well within IEC limits for power quality. A patented arc compensation system is installed and allows for full arc position control (to compensate for magnetic field induced arc deflection) so that a symmetrical crucible is maintained, significantly benefiting refractory life. The principal benefits gained from the MFC process is the fact that ore fines are processed, without metallurgical coke, and higher chrome recoveries are achieved compared to other smelting technologies when using a DC open arc for smelting. Keywords Samancor Chrome, Middelburg Ferrochrome, ABB, smelting, DC arc furnace, arc compensation, power factor correction, anode, harmonics, thyristor, reactor, maintenance, refractory, ores, reductants.

Jan 1, 2010

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

This paper presents an initial investigation into the viability of co-kriging the grades of multiple mining cuts in a two dimensional, thin reef scenario. Deposits with gradational mineralized zones, in the perpendicular sense, are not as well served by the use of reef accumulation and thickness as deposits characterized by a sharp distinction between ore and waste rock. South African Bushveld Complex platinum deposits and Witwatersrand gold deposits are examples of this distinction. The calculation of an optimal mining cut is of paramount importance in the mining of Bushveld platinum. Two-dimensional kriging of a constant stoping width mining cut is an effective method for resource calculations once a cut is decided, but this begs the question of how to decide on the cut. Comparison of multiple cuts is used as a way of achieving this decision on many of Anglo Platinum’s operations. Although the kriging of each cut is valid in isolation, occasional negative values occur when incremental grades between overlapping cuts are calculated. Negative incremental grades cannot reflect reality. They are thought to be related to the inability of the method to include the strong continuity in the perpendicular direction demonstrated by the relevant variograms. Co-kriging of related variables has been investigated as a potential means tore impose this inherent order relationship. Various co-kriging options have been investigated. The method has been tested on a real data set from an established platinum operation. One of three types of anomaly has been investigated so far. The results show that co-kriging the mining cut grade as the primary variable, with just one secondary variable, the reef thickness, eliminates most occurrences. Severe anomalies remaining are arguably indicative of population mixing and might be more effectively treated by rezoning the data. Aim—To investigate the viability of co-kriging the grades of multiple mining cuts as a method for resolving anomalies in the estimation of such cuts on Bushveld platinum deposits, with applicability to other thin reef type deposits with a gradational not sharp cut-off between ore and waste in the direction perpendicular to the reef. Keywords: co-kriging, cross variograms, ordinary kriging, platinum, two-dimensional, grade profile

Jan 1, 2003

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By S. Neilson, M. G. Demmer, K. McCarogher

The Phoenix Programme takes the Mining and Mineral Processing Industry into the Science Classroom In the early years of mining, methods were crude, simple, labour-intensive, and very slow. Human resourcefulness, however, created innovations (mechanization, and computerization), that resulted in faster development, greater tonnages of ore, more efficient separation, and a superior final product. This expansion occured an ever-increasing rate, and resulted in a booming mining industry and a growing economy.

Jan 1, 1989

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By S. M. Spottiswoode

Rock mechanics benefits of stope support in deep-level mining originate principally from the ability of the support to resist relative movements between the hangingwall and the footwall. While the role of stabilizing pillars and backfill on reducing the energy release rate (ERR) at the face is well understood on the basis of elastic behaviour of the rock mass, the effect of support on controlling movement of fractured ground around deep-level stopes has not yet been thoroughly studied. As part of a programme of studying the behaviour of this fractured ground, geophones were placed 10 m from the face on the roof and floor of a longwall stope in which packs were used as supports. It was found that differential movement between the roof and floor generally exceeds average stope movement during a seismic event. Conventional support therefore transmits very little seismic energy; this is expected to remain true until complete convergence occurs. In backfilled stopes, backfill can become at least as stiff as the fractured wall rock. This will have the effect of reducing the length of the hanging- wall beam. Amongst other rock mechanics considerations, a shorter hanging- wall beam should: (i) increase the resonance frequency of the hangingwall and thereby decrease the levels of vibration for seismic events with M > 1,0; (ii) reduce absolute vibration levels by increasing the mass of rock immediately adjacent to the stope which is shaken by seismic waves; and (iii) reduce differential movement between the roof and floor and thereby reduce cyclic strain on the backfill and on gully support.

Jan 1, 1988

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

At the Annual General Meeting of the Chamber of Mines of South Africa, held in Johannesburg on 29th June, 1982, the following leading members of the mining industry were elected to office for the 1982-1983 term: Mr W. W. Malan President Mr C. T. Fenton Vice-President Mr G. Y. Nisbet Vice President William Wouter Malan was born in Springs on 7th November, 1928, and was educated at the Springs High School and the University of the Witwatersrand, where he obtained a B.8c degree in mining engineering. Diamond Mines. Mr Nisbet became a consulting engineer of the Anglo American Corporation in 1972, and a deputy managing director of the Gold Division in 1974. George Young Kisbet was born in Benoni in 1923 and was educated at Pretoria Boys High and the University of the Witwatersrand. Mintek reports Report 2010D A process for the recovery of rare-earth oxides from monazite. (First published 16th March, 1979). Report 2073D A preliminary investigation of the concentration process at Ucar Minerals Corporation. (First published 19th September, 1980). Report 2092D The recovery of pyrite from gold ore by gravity separation. (First published 28th November, 1980). Report M13 Factors affecting the production of fines during the screening and handling of highcarbon ferromanganese.

Jan 1, 1982

By B. K. Loveday

The use of large flotation machines is well established, resulting in substantial savings in both capital and operating costs. Therefore, when a new plant is designed, laboratory and pilot-plant tests should be used to simulate large flotation cells, or appropriate scale-up factors should be employed. 'Conference on titanium The Fifth International Conference on Titanium will be held from 10th to 14th September, 1984, in Munich, West Germany, organized by the Deutsche Gesellschaft fur Metallkunde e.V., in association with the American Society for Metals, Societe Francaise de Metallurgie, The Academie of Sciences U.S.S.R., The Japan Institute of Metals, The Metallurgical Society of A.I.M.E., and The Metals Society.

Jan 1, 1983

By H. L. Monro

The individual supplies of and demands for gold that make up the total supply/demand structure in any year, together with their individual price elasticities, are used to determine the effect of forward sales on the gold price.

Jan 1, 1992

By D. G. Krige

The problem addressed is that of estimating grade differences between sub- divisions of a new gold mining prospect when only borehole results are available. Such differential grade estimates are required in choosing the best area for initial production, and in defining the grade profile over the mine's life for purposes of feasibility studies. It is also often necessary to differentiate between the grades and hence the values of subareas, owned by separate companies, for the purpose of fixing relative share participation percentages in the new mining company. It is shown that exaggerated grade differentials will be obtained from grade estimates of the subareas based only on boreholes within each such subarea, respectively, and that it would be more realistic to apply some 'smoothing', preferably by kriging. This is feasible because the lognormal-de Wijsian model can be used to give an indication of the spatial structure for the boreholes, even where they are spaced far apart; also the degree of 'smoothing' indicated is shown to be relatively insensitive to inaccurate estimates of the relevant semivariogram parameters.

Jan 1, 1987

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By M. Asghari, R. Amiri, A. Haratian, M. Noue Parast, S. Haji

Today the roller screen has a wide range of applications in the steel-making industry. It is used for screening of green pellets before using the kiln. Since the appropriate size of a green pellet is -16+9 mm, there are different gaps between rollers that make green pellets classified in three categories: -9 mm (undersize), -16+9 mm (onsize) and +16mm (oversize). The efficiency of a roller screen is specified according to the weight percent of undersize in onsize as a fine material, and weight percent of onsize in oversize (loss). This efficiency is influenced by different operational parameters such as roller diameter, roller speed, and roller gap, material type of rollers and inclination of roller screen. This study investigates the effect of different material types of rollers in efficiency of Ardakan roller screens, located in the Yazd province of Iran. The rollers of the existing roller screens in this pelletising plant are made of polyurethane which according to this investigation, has a maximum lifetime of about six months. Operating the polyurethane rollers beyond its lifetime generates serious problems such as high wear of rollers, and consequently, material buildup on the roller surface which then significantly decreases the roller screen efficiency. So, after examining different roller materials, stainless steel 304 with higher surface roughness to help pellets move properly on the roller screen surface was selected as a solution to this problem. The new roller screen was constructed by Fakoor Meghnatis Spadana (FMS) and replaced the previous one. In this way, the maximum capacity of the roller screen was increased about 17% and the roller screen efficiency was increased about 15%. Keywords: Roller screen, green pellets, efficiency, onsize, operational parameters

Jan 1, 2020

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By H. M. Friede, R. H. Steel

Notes on Iron Age copper-smelting technology in the Transvaal by H. M. FRIEDE, Ph.D. and R. H. STEEL (Visitors) Earlier reports on Iron Age copper metallurgy and copper-smelting techniques in the Transvaal are surveyed, and a description and tentative classification of the copper furnaces are given. The analyses of furnace slags and sherds of glazed crucibles from archaeological sites of the Transvaal and the neighbouring Orange Free State pro. vide evidence of copper smelting there in Iron Age times. . An investigation conducted by the Department of Archaeology of the University ofthe Witwatersrand provided information on the details of furnace construction and smelting processes, on the composition of the materials used and produced, and on the making and handling of tools and accessories, such as bellows and tongs, needed by Iron Age smelters. Three models (the KaondejVenda furnace, the Rooiberg crucible furnace, and the Uitkomst furnace) were constructed and operated as a demonstration of Iron Age copper smelting as it was practised in the Transvaal.

Jan 11, 1975