Search Documents

By R. P. Plasket, D. A. Ireland

Ancillary smelter operations and sulphuric acid manufacture at Impala Platinum Limited by R. P. PLASKET. Pr. Eng.. M.Sc. (Chem. Tech.). Natal (Fellow) and D. A. IRELAND. Pr. Eng.. B.Sc. (Chem. Tech.). Natal (Member) The de-watering, spray drying, and converter operations at Impala are described, aspects that may be new to the minerals industry in South Africa being elaborated. Air-pollution control necessitated the installation of a sulphuric acid plant to limit the emission of sulphur dioxide to the atmosphere. Closer control of the smelting and converting operations was required for successful operation of the acid plant on the inherently Iow and varied concentration of feed gas from converter blowing. Approximately 82 per cent of the sulphur entering the smelter is converted to sulphur dioxide, of which 67 per cent is fed into the sulphuric acid plant.

Jan 8, 1976

Iron ore pellets with or without additives are commonly used as alternate charge material in both conventional and newer ironmaking processes. The performance characteristics of these pellets are normally assessed on the basis of their reducibility values, reduction strength and resistance to clustering. These properties depend mainly on the type and amount of additives and on the sintering phenomena of the pellets during firing. In the case of composite pellets (ore-coal pellets), reduction and sintering of the iron ore fines occur simultaneously. The thermodynamic and reaction mechanisms of the processes involved in the reduction of iron ore pellets with and without reductants, additives, etc., may not necessarily be identical. The reduction and sintering characteristics of pellets greatly influence the reaction mechanism and the surface morphology of the reduced pellets. The approaches in the literature to the analysis of these reduction and sintering phenomena are broadly categorized as follows: (i) empirical models, (ii) models based on kinetics, and (ill) models based on morphological changes. The relative merits and de-merits of these models are illustrated by their application to the reduction of fluxed ore-coal composite pellets. A critical analysis of the investigations that have been conducted on the reduction and sintering behaviour of such pellets is given. It is shown that, although elegant empirical models and kinetic equations have theoretical significance and can be usefully employed in elucidating the reaction mechanisms of iron ore lumps, they are sometimes not directly applicable to fluxed ore-coal composite pellets. In studies of the latter, the approach should be to correlate the morphological changes with the reduction mechanism. The paper also gives a brief account of an investigation on the reduction and sintering aspects of fluxed composite reduced iron pellets.

Jan 1, 1996

By J. Gilliland

The Grootegeluk coal-beneficiation plant was erected in the Waterberg coalfield, near Ellisras in the Transvaal, to supply Iscor's steelworks with a predetermined tonnage of coking coal in accordance with strict quality requirements. This plant has to handle a high tonnage of raw coal, which is not easy to beneficiate, in order to produce 1,82 X IQ6t of coal. Extensive tests were conducted on borehole cores and a mass sample of coal obtained from the area. These tests were carried out on a laboratory and pilot-plant scale, and were aimed at the establishment of the most effective beneficiation methods and the choice of suitable equipment. This led to the completion of a full set of design and manufacturing drawings that resulted in the project approach . described in this paper.

Jan 1, 1982

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By G. Raspa

The paper describes a computer procedure for evaluating and selecting recoverable reserves in a mine worked by sublevel stoping. The boundaries of the volume to be mined are optimally defined by means of the 3-dimensional Lerchs-Grossmann algorithm, separately applied to both sides of the panels. The procedure, which has been developed for Masua Mine (Sardinia), also provides for smoothing the optimized boundaries, positioning the drilling drifts, interactive design of drilling fans and calculation of tonnage and grade of each volley. These tonnages and grades form the input of another procedure evolved for production planning.

Jan 1, 1987

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

By H. M. Friede, R. H. Steel

Tin mining and smelting in the Transvaal during the Iron Age by H. M. FRIEDE*. Ph.D. and R. H. STEEL* (Visitors) This paper reviews the historical, archaeological, and metallurgical evidence on Iron Age tin mining and tin smelting in Southern Africa. The results of the analysis of twenty samples of tin ore, tin slag, and tin ingots found associated with Iron Age materials in the Transvaal (mostly in the Rooiberg area) are reported and discussed. The types of ingots preserved in local collections are described. A small experimental tin-smelting furnace was constructed and worked according to traditional African Iron Age technology. Qualitative and quantitative results of this experiment are reported.

Jan 7, 1976

By Y. Lizotte

This paper describes the design and implementation of the dispatching system at LAB Chrysotile Inc.'s Black Lake Mine Operation, Quebec, Canada. The initial system uses a computer in a passive role, to record and display information in ongoing operations. Simulation studies were undertaken at McGill University to assess various heuristic dispatching rules which can be program- med and inserted into the dispatching system. The computer can then suggest to the operator where a truck should be sent to maximize productivity or improve fleet efficiency. The study stresses the importance of considering the effects of implementing computerized systems on those individuals who must use these systems in their daily work. The roles of individuals from the industry and the university in this joint project are also highlighted.

Jan 1, 1987

The refractoriness of the gold in many of the pyritic ores from the eastern Transvaal is due mainly to the association between the gold and the sulphides, but it can be due to the presence of graphltlc carbonaceous material, which complicates the recovery of the gold by virtue of its adsorption activity. In an examination of the roasting characteristics of three flotation concentrates from the Barberton area, It was found that the gold in the concentrates occurred mostly in two forms: in very fine gold particles distributed within the arsenopyrite, and in a slightly coarser form loosely associated with the pyrite. Direct cyanidation of the concentrates gave gold extractions of from 16 to 30 per cent. After the concentrates had been roasted at temperatures of 650 to 700°C for 20 minutes with rabbling, the extractions varied from 86 to over 90 per cent. Examination of the residues after cyanidation indicated that gold was present in the porous calcines or in the calcined sulphide product. This observation, together with porosity measurements, suggests that physical encapsulation of the gold particles is the main reason for the refractory behaviour of the gold in the calcines.

Jan 1, 1988

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By L. H. W. Walker

As part of an overall design of a computer based mining managerial system, the geological and mineral estates management disciplines find themselves centrally placed in terms of producing fundamental data both before and during the mining operation. Computerisation of all aspects of these fields of endeavour has come to be seen as essential for complete integration with other mining orientated disciplines. Release 1 .l. of the Anglo American system of mineral estates management has been tested and is in the process of being implemented at several Anglo American Gold Division mines.

Jan 1, 1987

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989

By M. B. Cortie

The historical development of materials engineering in the mining industry Is briefly reviewed, and some of the factors currently influencing the industry in South Africa are discussed. Material usages in various parts of the mining operation are surveyed. The predominant mechanisms in the degradation of materials in mines are wear, corrosion, and fatigue. The issue of corrosion-abrasion Is considered, but it Is concluded that abrasive wear predominates in most rock-handling and comminution applications and that, in general, little economic benefit Is to be gained in those applications by the use of existing corrosion-resistant alloys. However, alloys with a measure of corrosion resistance find profitable application elsewhere in the mining environment. The use of other engineering materials such as polymers, ceramics, al1l1inium, and various ferrous alloys may be economically viable in a variety of niche situations. Identification of the most cost-effective material in each case calls for a systematic approach and some patience.

Jan 1, 1996

By P. J. Kinver

This paper deals with the development of the cut-and-fill mining method at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province of South Africa. Lead, copper, zinc, and silver are produced. Production started in January 1976, being confined to blasthole production methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is 70 per cent depleted, and pillar extraction is in progress. The balance of the production tonnage, 60 kt per month, is produced from three cut-and-fill stopes situated in the flatter-dipping areas of the orebody. The cut-and-fill mining method at Black Mountain is a result of research and planning activities that included the use of modelling, laboratory tests, mathematical analyses, in situ tests, and experience gained from other mining operations. These investigations and the resulting developed methods and designs are summarized in the paper.

Jan 1, 1985

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995