Search Documents

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

This paper presents the development of a regrind facility design at BHP Billiton's Leinster Nickel Operations (LNO) in Western Australia. The recovery opportunity was identified from an analysis of plant operating data together with scanning electron microscope (SEM) measurements on relevant tailings streams from LNO. A laboratory procedure was developed to determine the potential recovery improvement of installing a regrind facility at LNO. The last step in formulating the process flow sheet and defining the process design criteria was to construct and operate a pilot plant, which incorporated four banks of flotation cells and an Xstrata M20 Isa Mill. Pilot plant on/off trials were used to define the expected metallurgical benefit. A prefeasibility engineering design and cost estimate was completed. Following a successful internal business evaluation, a feasibility study is currently underway.

Jan 1, 2007

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

1. Book reviews ? Second International Conference on Hydrocyclones. Cranfield (Bedford, MK43 OAT, England), BHRA Fluid Engineering Centre, 1984. £33. Reviewer: R.P. King This volume contains the 28 papers presented at the Second International Conference on Hydrocyclones, which was held in Bath (England) in September 1984. The format and presentation of the papers are similar to those of the first volume in the series, and this volume con¬tinues the series as an authoritative account of much of the research work associated with hydrocyclones that is being undertaken throughout the world. The volume was produced from camera-ready copy supplied by the authors, but the quality of reproduction is very high and both text and figures are legible throughout the volume. Although most of the work reported deals with the hydrocyclone as a classification device, important sections are devoted to liquid-liquid separations and heavy¬medium separations.

Jan 1, 1985

The 89th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 20th August, 1986. Mr. H. E. James (President) was in the chair and declared the meeting open at 16hoo. Obituaries President: It is my sad duty to announce the deaths of the following members of this Institute: Life Fellow D.L. Carson; Retired Fellows T.K. Adams, G.E. Carlyon, N.M. Holford, D.E. Maclver, C.J. Morgan; Fellows S.K. de Kock, R.R. Porter, Dr G.J. Rees; and Associate Sir Lindesay Clark. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, please rise and observe a moment of silence. Minutes President: The 88th Annual General Meeting of the Institute was held on Wednesday, 14th August, 1985, and the minutes were published in the September 1985 issue of the Journal. The minutes were confirmed.

Jan 1, 1986

By P. De Kock

Strategic mine planning is concerned with the decisions that determine the value of the business, while tactical planning deals with the tasks to realize that value. When tasked with formulating a strategic mine plan, the mining engineer often turns to commercially available software. However, these software packages have limited applicability to the RBM situation. Adopting a simpler, back to basics approach founded on a deep understanding of the economics of the orebody has the advantage of providing a clear logic to guide tactical planning. By creating a coherency between strategic mine planning, and tactical planning the likelihood of successfully executing the plans and attaining the value promised by the strategic plan is increased. This paper describes the reasons why RBM embarked on a strategic mine planning process, the rationale of choosing the process, and the process itself.

Jan 1, 2007

By I. O. Flores, A. Anani, H. Li

Current technological advancement has increased the exploitation of deeper ore bodies using underground methods. In certain cases, the mineral deposit starts near the surface and continues deep within the earth's crust. Such deposits are best mined with both underground and surface methods. Two main techniques are used to determine the optimal transition depth from surface to underground - a disintegrated approach and an integrated approach. Both methods have limitations in their use to determine the optimal transition depth. The objective of this research is to investigate the conditions in which an integrated approach to the transition depth problem is superior to a disintegrated approach. Three binary integer linear programming models are developed for this purpose: a surface and underground model for the disintegrated instance and an integrated model. A case study is performed to validate the models, with a comparative sensitivity analysis to obtain operational insights.

Sep 1, 2021

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By M. C. van Eeden, R. Vermeulen, K. B. Le Bron

This paper presents the lessons learnt during the transition from an open pit method to a sub-level open stoping method at the Koidu Limited kimberlite pipe. These learnings may assist other mines with planning, both from a practical implementation perspective (layout, charging up challenges), and a method for estimating potential dilution and stability challenges associated with the interaction between the surface and underground excavations. Predictive geotechnical stability modelling was successfully applied to highlight potential failure zones, which allowed modification and enhancement of the mining layouts and quantification of the potential dilution of the kimberlite from indicative instabilities.

Sep 1, 2025

By Pentti Niskanen

"The ventilation system of the Pyhasalmi Mine is described. The mine is located in an area where the annual atmospheric temperature may vary from +30°C to -30°C. Natural ventilation causes serious difficulties because the underground mine is connected by drifts and finger raises to the bottom of the 120 m-deep open pit.The natural ventilation tends to make the ventilation net unstable. The paper describes how the instability characteristics of the ventilation net can be studied and how they have been taken into account when automating the control of the ventilation. In addition, the software, hardware and costs of the system are described. The system consists of 12 automated ventilation doors, two mine fans, 8 elements for sensing the air flow and temperatures, a control panel and a process computer."

Jan 1, 2014

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By Paul B. Crawford, Gerald N. Pitts

"A new method is introduced for the simulation by computer of the flow of liquid underground. The method has application in simulating, for example, liquid withdrawal systems, injection systems or injection-well systems. The computer simulation of liquid flow permits the utilization of the known properties of the rock in developing a model of the permeable rock mass.The flow properties of the rock at a specific site arc generated statistically using a random number generator. After defining in this manner the rock properties of each element in the computer grid, the streamlines or flow paths of the liquid are traced using the new method. The simulation is designed especially for computers. The meandering character of the liquids paths is displayed clearly as the fluid moves underground, thus providing the technical information required for the control of the movement of liquid."

Jan 1, 2014

By Z. Song

Real-time monitoring makes it possible to detect any disturbance occurring in production, while decision instruments can efficiently assist decision-makers to optimize production, reduce iterative workload, obtain better solutions, and preview possible results. Technologies for the above already exist and have been proven in the process industry, i.e. refining and smelting. Optimization is also essential for profitable and stable mining production. Real-time monitoring has already taken hold in mining operations, especially in surface mining, while optimization techniques have also been widely used in underground mining, particularly for planning and scheduling. This review is limited to the hard-rock mining production of metallic ores such as gold and copper. It reviews optimization techniques developed for mine planning and scheduling, and communication technologies suitable for underground applications. It also presents control features for individual operation units, and discusses the technical viability of a mining production real-time optimization (MPRTO) system for underground mines, with possible benefits and challenges. Operational disturbances always occur in mine production. An MPRTO system can be useful to maintain operational effectiveness and efficiency by allowing quick changes to short-term plans. This paper briefly describes the MPRTO system, including the input, output, and basic algorithms. The technical prerequisites for the system specified here are already available. Further studies that are required to improve the system are discussed. Keywords real-time optimization, underground mining, production, operation.

Dec 1, 2013

By H. W. Glen

The use of a personal style (mainly active voice and first person) makes technical writing more pleasant to read, and helps the writer to express his meaning clearly and to avoid many of the stylistic errors normally encountered in that type of writing.

Jan 1, 1979

The optimization of sample spacing In South African gold mines by J. M. RENDU*, Eng. Se.D., M.S. (Min.) U.S.A. (Graduate Member) A first attempt is made at optimization of sample spacing in South African gold mines. The De Wijs model, which is shown to give a good representation of the geostatistical properties of gold values, is used to analyse the influence of the distance between samples along a stope face on the error of estimation of the stope value. The influence of other factors such as the face advance before resampling, the sample density, and the stope size, is also considered. Practical conclusions are drawn concerning the optimum sampling policy to be followed in various situations, and it is shown that sampling on a regular grid does not necessarily give the best results.

Jan 4, 1976