Search Documents

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

The confusion caused by the different numerical representations of time in the ever-increasing international exchange of information has underlined the need for a world-wide uniform representation of time.

Jan 1, 1989

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men's rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

1. Publications of The Institute of Metals The following publications are available from The Institute of Metals, Sales and Marketing Dept, 1 Carlton House Terrace, London SWIY 5DB, England. . Intermediate temperature embrittlement processes in duplex stainless steels. 1990. £15.00. This is a special issue of Materials Science and Technology containing the full proceedings of the international workshop held in Oxford in August 1989. . Worked examples in dislocations, by M.J. Whelan. 112 pp. £16.00. This is a concise introductory text that examines aspects of the theory of dislocations. . Introduction to creep mechanisms, by B. Wilshire. 1991. 112 pp. Well-supported by diagrams and illustrations, this concise introductory textbook allows students and engineers to increase their knowledge of modern theoretical and practical approaches to creep and creep fracture. . Powder metallurgy. A series of lectures. 1991. (Looseleaf binder). Originally published in 1986 by the Fachverband Pulvermetallurgie, this course book provides an introduction to PM technology. Divided into eight thematically distinct sections, it also contains numerous illustrations and tables, as well as 150 slides. The concluding section contains an extensive reference list to the literature for readers wishing to study topics in greater detail.

Jan 1, 1991

Book new a Book reviews Economics of the mineral industries. 4th Edition. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). 660 pp. Reviewer: M.A. Ford Foundry technology, by P.R. Beeley. Durban, Buterworth Scientific, 1982. R124 + GST. Reviewer: A.P. van Wyk Underground Transport Symposium. Johannesburg, The South African Institute of Mining and Metallurgy Special Publication SP 1. 300 pp. R65 (Non-Member), R55 (Member), + GST. Reviewer: C.L. Workman-navies A summary of the Project DevelopmentSymposium as presented by The Australasian Institute of Mining and Metalurgy. $A 25.00. Reviewer: D.J. van Niekerk Geology of uranium deposits. Proceedings of the CIM-SEG Uranium Symposium, September 1981, edited by T. I. I. Sibbald and W. Petruk. Quebec, The Canadian Institute of Mining and Metallurgy, Special Volume 32, 1985.268 pp. Canadian $40 members, $50 non-members (plus $3 for postage and packaging). Reviewer: M.S. Toros Crushing and grinding process handbook. Chichester (England), Wiley, 1986. £49. Reviewer: M.P. Hay O'okiep's 50th birthday The 0'okiep Copper Company Limited, situated at Nababeep s,ome 35 km from Springbok, recently celebrated its fiftieth anniversary.

Jan 1, 1987

By E. Shavartz, N. B. Strydom

The incorporation of individual cooling in a compressed-oxygen closed-circuit breathing apparatus by E. SHVARTZ, M.Sc. (U.C.L.A.), Ph.D. (U.S.C.) (Visitor) and N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow) A conventional compressed-oxygen breathing apparatus, which did not include provisions for dehumidification of the inspired air at high environmental temperatures, was tested at these temperatures with and without conductive cooling in the form of 2 kg of pre-frozen ice placed inside the breathing bag of the apparatus. The pre-frozen ice provided conductive cooling of the soda lime and of the chest and abdomen of the subject, who performed moderate work at 50,1 "c. Without cooling, the subject was exhausted after 35 minutes because of a wet-bulb temperature of the inspired air of 46"c. With cooling, the subject finished 2 hours of work. This was possible by keeping the soda lime at a relatively Iow temperature, which resulted in a wet-bulb temperature of the inspired air of only 42 °C after 2 hours, and by conductive cooling of the chest, which resulted in the maintenance of a relatively Iow heart rate and rectal temperature.

Jan 7, 1975

By A. L. Hinde, A. A. Bradley, K. H. Stanton, P. J. D. Lloyd, G. K. Schymura

As part of its programme to develop methods for concentrating minerals underground, the Chamber of Mines of South Africa in conjunction with Lurgi evolved and tested a I MW centrifugal mill. The machine is capable, in the autogenous mode, of grinding more than 25 t/h of minus 75 plus 44 mm hard quartzite to a minus 3 mm product containing over 50 per cent minus 75 µm material, and as a ball mill of grinding more than 60 t/h of minus 19 mm quartzite to a minus 3 mm product containing over 35 per cent minus 75 µm material. Extrapolation of computer models of the process suggests that these limits can be comfortably exceeded. Long-term continuous testing is in hand, aimed at proving that this I m in diameter by I m long mill is in every respect the equivalent of a conventional 4 m by 6 m ball mill.

Jan 1, 1982

By R. A. H. Lycett, P. R. Jochens, D. D. Howat

The crystallization of rutile from titaniferous slags by R. A. H. LYCETT, M.Se. (Eng.),"A.M.I.M.M. (Visitor), P. R. JOCHENS, Pr. Eng., M.Se. (Eng.) (Rand), Ph.D. (Member), and D. D. HOWAT, B.Se., Ph.D., F.R.I.C., F.I.M. (Fellow) Factors affecting the precipitation of rutile from smelter slags were investigated, with particular reference to the effect of additions of phosphorus pentoxide to the slag. The phases were identified and the phase boundaries determined for slags having phosphorus pentoxide additions of 0 to 50 per cent. The liquidus temperatures of these slags were determined, and a pseudo-binary phase diagram was constructed. Rutile crystallized as the primary phase from melts having a phosphorus pentoxide content of more than IS,S per cent. Prismatic rutile crystals whose TiO. content was more than 97 per cent were grown from melts that had a phosphorus pentoxide addition of 30 per cent. However, the morphology of the precipitated rutile was such as to make subsequent separation impracticable.

Jan 9, 1975

By M. G. Spengler

A new type of pack has been developed primarily for the support of narrow stopes. It was shown in the laboratory that it has characteristics that very closely approximate the optimum required by underground support to achieve hangingwall stability.

Jan 1, 1978

By B. Moritz, W. Schubert, E. A. Button

ABSTRACT: Geological conditions associated with alpine environments in combination with high overburden in many tunnelling projects lead to squeezing behaviour. The main problems associated with such conditions include large deformations, overstressing of supports, and lack of face stability. In the past during Alpine tunnelling the problem of large displacements incompatible with rockbolt – shotcrete support systems have been solved by leaving gaps in the lining to accommodate excessive deformations. In the late nineties, yielding elements have been developed, which are integrated into the lining. The paper deals with the basic concept, the design and the application of that system, which has been successfully used in several Alpine tunnels. ZUSAMMENFASSUNG: Die geologischen Verhältnisse in den Alpen führen bei großer Überlagerung häufig zu starken Deformationen während des Baues von Tunneln. Die großen Verformungen führen in vielen Fällen zu einer Überbeanspruchung des Ausbaues und Problemen mit der Ortsbruststabilität. Früher ist man dem Problem der Unverträglichkeit des Ausbaues mit den hohen Dehnungen durch Freilassen von Deformationschlitzen im Spritzbeton begegnet. Vor etwa 10 Jahren wurden duktile Stahlelemente entwickelt, welche in die Spritzbetonschale integriert werden. Der Beitrag beschäftigt sich mit dem Konzept, der Planung und der Ausführung. RÉSUMÉ: Les conditions géologiques dans les Alpes conduisent fréquemment lors d'un grand recouvrement à des déformations fortes pendant la construction des tunnels. Les grandes déformations conduisent dans beaucoup de cas à une surtension du revêtement et à des problèmes avec la stabilité de front de taille. On a fait face plus tôt au problème de l'incompatibilité du revêtement avec les extensions élevées par libérer des rainures dans le béton projeté. Il y a environ 10 ans, des éléments sidérurgiques ductiles qui sont intégrés dans le béton projeté ont été développés. La contribution s'occupe de concept, de planification et de mise en oeuvre.

Jan 1, 2003

By B. P. Watson

The Bushveld platinum group metal deposits in South Africa are the largest in the world. These deposits occur as two distinct stratiform tabular ore bodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2300 m. The mining method is a variation of planar open stoping. Crush pillars are widely used to support the open stopes. These pillars are designed to fail and the residual strength provides the required support resistance to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC modelling, with strain softening, was done to investigate how damage expands into the hanging- and/or footwall. Although the so-called ?squat? effect is always present, the modelling suggests that it does not dominate the pillar system behaviour at larger width to height ratios. Punching of the pillar into the hanging- and/or footwall increasingly controls the pillar system behaviour with larger width to height ratios. The paper investigates the behaviour of a system that incorporates the immediate hanging- and footwall, as well as the pillar itself.

Jan 1, 2009

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

1. Book review . Australasian coal mining practice, edited by C.H. Martin. Reviewer: R.B. MacGilIivray This book is an extremely comprehensive coverage of coal-mining practice in Australasia, the countries covered being Australia, New Zealand,and Papua New Guinea. 2. From The Institute of Metals The folowing are available from The Institute of Metals, 1 Carlton House Terace, London SWl Y 5DB. Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00. High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15. New cored-wire injection techniques, particularly as Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45. Marine engineering with copper-nickel. 1988. 103 pp. £18. Characterisation of High Temperature Materials. 3. New journal FMJ International Publications Lid have announced a new quarterly publication, Aluminium Today. 4. Other new publications Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95. Proceedings, Foundry and Heat Treatment 88. R150 per set of 5 volumes, or R40 per volume.

Jan 1, 1989

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

By A. Hinde, M. Moys, L. C. Woollacott

The material-balance smoothing technique is applied directly to the problems associated with the evaluation of the performance of backfill-preparation plants. A computer package specially designed to assist the process engineer in such evaluations has been developed. The usefulness of the technique as compared with other methods for the extraction of meaningful information from backfill-plant data is demonstrated.

Jan 1, 1992

By Wm. Bleloch

SYNOPSIS The feasibility of rejection of nitrogen from stack gas by recycling of top-gas with cold-blast 95 to 98 per cent oxygen is assessed. It is concluded that nitrogen could be removed to a level below 3 per cent of the stack-gas using recycled cleaned cold top-gas and 95 to 98 per cent oxygen produced by a single-column air separation plant with liquid-air reflux instead of liquid nigroten reflux. The partial pressure of carbon monoxide in the stack-gas could be doubled without top pressure and the deposition of carbon and reduction of iron oxides by the stack gas could be markedly increased. It is concluded that rate of stock descent could be doubled compared with present-day practice and an iron make of 4400 kg/m 2 of hearth area/hour may be attainable with a working volume of 129 m2/m hearth diameter by this method. Oxygen consumption is estimated at possibly 280 m2 (0.4 t)/t iron made and carbon consumption at possibly 280 kg/t iron. Power consumption for oxygen including auxiliaries is estimated at 304 kWH/t 100 per cent oxygen as 95 to 98 per cent gas. The air separation cycle due to Schuftan is discussed in some detail, and the components of a 1 600 metric ton/day separation plant are briefly discussed. The paper is a theoretical essay.

The variety and sources of sampling errors have been studied since the late 1800s, but the pioneering work of Pierre Gy in the 1950s provided insights into sampling as an error generating process. Total sampling variance is a measure of the total sampling error, but disaggregating the variance into its component parts is problematical. Ten sources of error and error generating processes have been identified, some of which can be eliminated through rigorous application of the principle of correct sampling. Others can only be minimized but never eliminated. Three principal questions relating to the appropriate mass of a sample, the fragment size of the sample and the size of the associated error are addressed. These questions relate principally to the Fundamental Error (FE), the only error that can be estimated before the sampling event. Aspects of constitutional and distributional heterogeneity are examined, as are the essential components of Gy?s formula including the shape factor (?), the granulometric factor (g), the mineralogical composition factor (c), and the liberation factor, l. Applications of Gy?s equation to the problems of sampling in the minerals industry are explained using real-life examples. The approach to sampling taken by Pierre Gy provides an excellent inferential relationship between the mass of material to be sampled, the size of the fragments being sampled, and the relative variance of the sampling error. It also provides solutions for three of the main problems associated with the Theory of Sampling.

Jan 1, 2007

By S. P. Molefe

Mr Chairman, members of the executive committee, the sub-committee, distinguished speakers at this opening plenary session, delegates, affiliates, ladies and gentlemen. It is with pleasure that I have been called upon today to make these opening remarks and officially welcome you al at this auspicious assembly, the Fifteenth Congress of the Council of Mining and Metallurgical Institutions. Not only am I pleased to open the proceedings at this plenary session but for me to do so at Sun City in the North-West Province makes me doubly pleased. It is my wish that al delegates and their companions will enjoy the activities that are planned throughout the Congress and leave here with minds refreshed and stimulated by the technical sessions and memories enriched by being in such a unique and truly delightful setting as exists here at Sun City. The mix of delegates present reflects CMMI activities in many countries throughout the world-Australia, Japan, China, United Kingdom and South Africa among others. When it comes to mining and related activities, South Africa has a place at the top, a dominant role in platinum, gold, chromium, vanadium, dimension stone, coal and so forth, and here in the North-West Province we can proudly declare that some 25 per cent of the revenue from minerals in South Africa, namely R47 billion come from this area. Furthermore, we lead in the production of platinum group metals with 94 per cent of South Africa's total sales and thus hold first place in the world, 46 per cent of dimension stone sales, 32 per cent of chromate and 25 per cent of gold sales.

Jan 1, 1994

By C. Ringas, F. P. A. Robinson

Various theories proposed to account for microbial corrosion are reviewed as a background to a better understanding of this type of corrosion in iron-based alloys. Experimental evidence is presented to show that even stainless-steel alloys are prone to microbial attack by sulphate-reducing bacteria. The corrosive attack by the bacteria is due primarily to the hydrogen sulphide that is produced as part of their metabolic processes.

Jan 1, 1987