Search Documents

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By W. S. Steinberg

Keywords: Pyrometallurgy, furnace, open slag bath, Evraz, Highveld In 1963, the full-scale engineering study for the development of an Iron, Steel, and Vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steel works that produced steel and vanadium-bearing slag by using a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for pre-reduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to Open Slag Bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of a higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By Y. Z. Ma

This paper presents a matrix formulation of factorial kriging, and its relationships with simple and ordinary kriging. Similar to other kriging methods, factorial kriging can be applied to both stationary and intrinsic stochastic processes, and is often used as a local operator. Therefore, the concepts of intrinsic random function and local stationarity are first briefly reviewed. Kriging is presented in a block matrix form in which the kriging solution is useful not only for understanding the relationships between simple and ordinary kriging methods, but also the relationships between interpolative kriging and factorial kriging. When used as a signal/noise-filtering method, factorial kriging is especially useful for multiscale modelling. Examples for general signal analysis and geophysical data signal filtering are given to illustrate the method..

Jan 1, 2014

By L. Scott, M. A. Goncalves

Effective communication is a sought-after non-technical skill in the health, safety, and environmental (HSE) function and is fundamental in achieving an organization’s safety objectives. While different channels are used to communicate HSE matters, many organizations employ posters, videos, and/ or signs containing images to convey information. Communication through signage and graphical hazard symbols has been regulated in standards, but vast sections of HSE communication are bespoke communications and exist outside the sphere of standards. Effective HSE communication through images requires an understanding of the organizational culture in which the images will be used, as well as an understanding of the semiotics of the images themselves. Creative interpretation within HSE communication can create situations where the message that was received is not the message that was intended, leading to confusion and misinterpretation. This paper is aimed at elucidating the semiotics of South African HSE visual content. It was found that the indexical mode of images was most preferred in visual communication, and text-only designs the least preferred. Senders and receivers of messages differ in their opinions on the complexity of HSE communication.

Feb 2, 2021

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005

By S. J. Swart

This paper discusses the principles and application of risk assessment and management as the basis for environmental management within the mining industry. Unlike in other industries, mines are required to obtain closure certificates in terms of section12 of the Minerals Act, which should ultimately release them from further environmental responsibilities. It is emphasized that the concept of environmental risk assessment and management, when applied correctly will mean that the mine will be identifying and managing environmental issues beyond those set by current legal requirements and management strategies. The focus shifts from conventional minimum legal compliance management to management of real environmental risks. The advantage of this approach is that the perceived ?shifting of legal and management goal posts? due to changing environmental laws or management principles, will not influence or dictate the mine?s short or long-term management objectives or actions, mine closure funds can be more accurately determined and mine closure should become a relatively simple procedure. The risk assessment approach has been applied to the planning of mine closure at Iscor?s Durban Navigation Collieries (Durnacol) in Kwa-Zulu Natal and certain key risk issues such as the long-term risk of water pollution from coal discard dumps have already progressed to fully quantitative risk assessment. This paper will discuss the process, which has been followed to date, with particular emphasis on the most recent phase, namely quantitative risk assessment and management of pollution from coal discard dumps. It is believed that the approach that is being pioneered at Durnacol and which overcomes some of the more obvious deficiencies of both the EMPR and the traditional IEM process will ultimately serve as the model for all responsible mines in South Africa. It is also believed that this approach will enable the authorities to issue closure certificates with the confidence that there will be no unforeseen surprises in the years after closure.

Jan 1, 1998

By J. Roodt

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree This work was done to characterize the leaching of a uranium containing pulp processed by a South African producer to identify parameters that could be adjusted to increase the extraction of uranium in the existing circuit. Batch leach tests were used to characterize the leach properties and especially the influence of the oxidant concentration on the leaching achieved. It was found that relatively high extraction could be obtained even at room temperature by using a high liquid-to-solids ratio and that increasing the oxidant concentration significantly improved the leaching of the uranium minerals.

Jan 1, 2003

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By L. Wade

The University of Nottingham, in conjunction with the University of Kentucky and The Society of Mining Engineers of America, hosted the International Symposium on Underground Mining Methods and Technology from 8th to 10th September, 1986. The programme was based on the central theme 'Coal Mining under Adverse Conditions'.

Jan 1, 1987

By N. Andersen

During the preliminary design phases and feasibility study of a proposed vertical shaft, a vertical diamond drill-hole is normally drilled on the site. This paper outlines how rock mass characteristics, in-situ rock stress, rock strength, hydrological characteristics, and structural parameters can be determined using wireline logging of this borehole. In addition, a rock mass classification scheme is developed, based on published work, and in particular the Q-factor is adapted to assess the stability of raise-bored shafts. The ‘stick plot’ is introduced, which combines all geotechnical parameters applicable to the stability of a vertical shaft into a colourcoded format where cross-correlations can readily be made on a day-today basis during the shaft-sinking process.

Jan 1, 2015

By V. Arslan

In this study, effects of the inert constituents, such as ash, and the effect of blending coals with differing rank and composition on the plasticity of coal blends were investigated. The reference coal originated from the Zonguldak region, in the north-west part of Turkey. Firstly, the effect of coal ash on the plasticity of Zonguldak coal was determined. Secondly, the relationship between the plastic properties of the individual coals and those of the blended coals were identified. Some important relations were found, related to the characteristics of the individual coals. Ultimately, the manner in which the plasticity of Zonguldak coal was affected by blending with low volatile coals was investigated. Keywords: coal blending, coal plasticity, coke, fluidity, rank.

Jan 1, 2006

By J. Bongardt

Ecologically acceptable techniques are described for the handling of waste materials from the fabrication industry. New production methods and the recycling of sludges from grinding and other waste materials are suggested.

Jan 1, 1997

By M. F. Wells

The method used to salvage South Deep?s Main Shaft after it was flooded by an inrush of water at about 450 m below collar on 1 May1996 is described. The individual techniques employed in the salvage were all proven technology, but the combination in which they were applied is considered to be novel. The operation involved the following activities in order of occurrence. ?the dewatering of the shaft with submersible pumps ?the placement of a French drain on the shaft bottom muck pile ?the positioning of large diameter heavy walled draft tubes, and smaller tightening up, grout intrusion and reverse flow pipes ?the casting and curing of a structural concrete plug; the capping of the draft tubes; the intrusion of several thousand tons of cement grout into the aquifer by pressure induced reverse flow ?the sealing of the aquifer ?extensive probe drilling and sealing of the zone around the inrush point with cement and other specialized grouts ?the mining out of the plug and the re-establishment of normal sinking routines.

Jan 1, 1999

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By E. V. Lilford

Valuators of mineral properties are faced with a range of valuation methodologies, the most important of which are grouped under the headings of the market approach, the cost approach and the income approach. The way in which value is defined and the detail of the different valuation methodologies is examined here. This paper aims at documenting the variety of valuation procedures and applying each method to a variety of gold projects and comparing the outcomes. Any decision to apply a valuation technique will depend principally on the stage to which the project has been developed. The valuation approach to a greenfield project will be substantially different from that applied to a well-drilled, extensively explored mineral property. Furthermore, a valuation exercise may produce different outcomes for the same gold project depending on which method is applied. In order to investigate the variability in valuation methods and to explore the outcomes of different approaches, a series of five gold projects was analysed. The projects differ in regard to levels of capital application, infrastructural setting, depth below surface, in situ grade, and the stage of development, and were valued using the different methods. The most critical aspect of any valuation is the capacity of the valuer to identify the salient issues and ensure that they are incorporated into the valuation. The danger of simply applying ?black box? solutions to valuation problems without a full understanding of the parameters and the areas of uncertainty is emphasized. The importance of the valuator?s experience, insights into best practice and the ability to recognize and submit to the requirements of compliance within the minerals industry is among the most important characteristics of a valuer.

Jan 1, 2005