Search Documents

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By R. L. Setsepu, S. O. Bada, J. Abdulsalam

The utilization of biomass as a solid fuel for co-firing has received great attention from boiler manufacturers as a clean coal technology (CCT) option. This research aimed to produce biocoal pellets, as a clean energy fuel, using hydrochar from trees planted to rehabilitate acid mine drainage (AMD) water and fine coal discards. The hydrochar was synthesized by hydrothermal carbonization of Searsia lancea harvested from AMD-contaminated land at a temperature of 280°C and a residence time of 90 minutes. It was blended with discard coal (–1 mm) at ratios of 25% and 50% hydrochar to produce different forms of solid pelletized biocoal (BC). The physicochemical and mechanical properties of each of the biocoal pellet blends were determined. The 100% hydrochar had the highest calorific value of 29.99 MJ/kg, while the raw discard coal had a calorific value of 16.73 MJ/kg. The ash content decreased from 42% in the discard coal to 25% in the blend of 50% coal and 50% hydrochar biocoal pellets. Biocoal pellets comprising 25% hydrochar and 75% discard coal (BC25 HC/75 COAL) displayed the best mechanical properties (compressive strength 3.06 MPa) of all the fuels, but the physicochemical properties were inferior to the BC50 HC/50 COAL pellets. This research has demonstrated that hydrochar synthesized from a tree species planted for hydraulic control of AMD has the capability to act as a binder for improving the mechanical properties and energy characteristics of fine discard coal.

Dec 1, 2021

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020

By R. Altındag, D. Akbay

The point load index is a simple, fast, and inexpensive method for determining rock strength and can be applied both in the field and in the laboratory. There are, however, some disadvantages and limitations to the method, and the test results can be affected by the person carrying out the test, the rock characteristics, or the test device. In this study we describe an investigation into how the point load index value is affected by the shape of the conical platens used in the test. Point load index tests were carried out using different devices fitted with conical platens of different spherical radii, and on a modified device which circumvented the limitations/disadvantages. It was seen that the point load index value increased as the platen radius increased, as expected. In the case of testing using non-standard conical platens, an equation is proposed to normalize the point load index value with respect to the standard spherical radius value.

Nov 1, 2021

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By S. T. L. Harrison, A. Kotsiopoulos, J. R. Amaral Filho, J. L. Broadhurst

The land disposal of voluminous fine-grained tailings from the processing of mined ore bodies poses a long-term risk to the surrounding environment and local communities, while also representing a loss of valuable natural resources; including water, land and mined minerals. To date, the development and practical implementation of alternative approaches and technologies for removing risk and reducing the burden associated with these wastes, particularly in South Africa, remains limited, and value recovery is largely limited to the extraction of precious metals. To this end, researchers at the University of Cape Town have developed a programmatic multi-phased approach to explore and develop opportunities for the valorisation of large-volume mine wastes, based on the innovation value chain. This paper outlines this conceptual approach and presents key outcomes from its application for the specific case of sulfide-bearing coal processing wastes from South African collieries. Through the application of a combination of qualitative and quantitative tools and methodologies, a number of potentially viable opportunities and processing routes for value recovery and bulk re-purposing of these wastes have been identified and tested on a laboratory scale. Studies have, however, also shown that there are several technical and non-technical factors currently constraining commercial application of these opportunities. Overcoming these constraints will require a commitment to innovative waste management approaches and effective multi-sectoral collaboration. Keywords: Coal processing wastes, physical separation, waste re-purposing and utilisation, technology transfer

Jan 1, 2020

By F. Rwere, A. Masasire, P. Dzomba, M. Mupa

Accurate determination of platinum group metals (PGMs) and gold (Au) has always proven to be a difficult task, due to their low concentrations in platiniferous ores. The most common preconcentration technique used in analysis of these metals is fire assay with a flux containing nickel or lead. This technique can be improved by using co-collectors. Here we hypothesise that Fe, Co, and Cu can be used as co-collectors to enhance separation and preconcentration of PMGs and gold by fire assay. To test this hypothesis, geological exploration samples from Siyanda Union Mine (Northam, South Africa) were analysed by an inductively coupled plasma-optical emission spectrometer (ICP-OES) for PGMs (Pt, Pd, and Rh) and Au. A control sample (certified reference material AMIS 0426) was also analysed by the same technique. The PGM and Au recoveries from the control sample ranged from 83% to 105% for all three co-collectors, with relative standard deviations less than 10% for the control sample and 7% for the geological samples. The PGM and Au recoveries by Fe and Co co-collectors were modestly higher than that of the Cu-collector. These results indicate that Fe and Co are better co-collectors than Cu, presumably due to the loss of analyte when using Cu. Taken together, Fe and Co co-collectors can be viable alternatives for analysis of PGMs and gold using the fire assay method.

Jan 2, 2022

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

By Steven Rupprecht

"The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. Some of the changes and their reasons are discussed. INTRODUCTION The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of Exploration Results, Mineral Resources and Mineral Rreserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The proposed 2016 update is not significantly different from previous versions of the Code. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. The Code sets out minimum standards, recommendations and guidelines for public reporting. However, reporting may be unclear, ambiguous, selective, obscure, distorted or unintelligible. Part of the purpose of the update is to provide better guidelines to Competent Persons (CPs) to ensure that the material information is being reported and that reporting is transparent in accordance with the guidelines of the Code. The information provided should, as required by the Code, be adequate to inform the “reader/investor or potential investor to make a reasonable and balanced assessment of the significance of the information”. The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) highlights the importance of the reporting Codes, as provided from a quote from their website (www.crirsco.com): The mining industry is a vital contributor to national and global economies. It is a truly international business that depends on the trust and confidence of investors and other stakeholders for its financial and operational well-being. Unlike many other industries, it is based on depleting mineral assets, the knowledge of which is important prior to the commencement of extraction. It is therefore essential that the industry communicates the risks associated with investment effectively and transparently in order to earn the level of trust necessary to underpin its activities."

Jan 1, 2015

By M. Kumral, Y. A. Sari

Underground mining operations tend to have higher operating costs than surface mines. When metal prices decrease, profitability is jeopardized due to the high costs. Therefore, mining management harnesses new practices that increase operational efficiency. One way to manage this challenge is to invest in new mine planning practices. Stope layout optimization as a part of underground mine planning aims to identify a portion of the orebody in the form of production volumes (stopes) to maximize profit under roadway and stope dimension constraints. In this paper we propose a novel approach based on identifying ore-rich areas of the deposit and prioritizing their extraction through an iterative heuristic clustering approach. The proposed approach is compared with and validated by an exact method through a small mining example. The heuristics produced nearly identical results in a very short time. Finally, a case study was carried out using a larger data-set. The cluster-based iterative approach generated nearoptimal stope layouts in a computationally effective manner.

Mar 1, 2021

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By A. M. Venter, C. W. Siyasiya, N. K. K. Arthur, M. G. Willemse, D. Marais

Although additive manufacturing is fast gaining traction in the industrial world as a reputable manufacturing technique to complement traditional mechanical machining, it still has problems such as porosity and residual stresses in components that give rise to cracking, distortion, and delamination, which are important issues to resolve in structural load-bearing applications. This research project focused on the characterization of the evolution of residual stresses in Ti-6Al-4V extra-low interstitial (ELI) additive-manufactured test samples. Four square thin-walled tubular samples were deposited on the same baseplate, using the direct energy deposition laser printing process, to different build heights. The residual stresses were analysed in the as-printed condition by the neutron diffraction technique and correlated to qualitative predictions obtained using the ANSYS software suite. Good qualitative agreement between the stress measurements and predictions were observed. Both approaches revealed the existence of large tensile stresses along the laser track direction at the sections that were built last, i.e., centre of the top layers of the samples. This in addition leads to large tensile stresses at the outer edges (corners) which would have the effect of separating the samples from the baseplate should the stresses exceed the yield strength of the material. Such extreme conditions did not occur in this study, but the stresses did lead to significant distortion of the baseplate. In general, the microstructures and spatial elemental mapping revealed a strong correlation between the macro-segregation of elemental V and the distribution of the β-phase in the printed parts.

Feb 6, 2023

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985

1. Book reviews Dislocations and properties of real materials, edited by M.H. Loretto. London, The Institute of Metals, 1985. 392 pp. Reviewer: F.R.N. Nabarro Au &Ag heap and dump leaching practice, edited by J.B. Hiskey. AIME, 1984. 162 pp. $20 (member), $15 (student member), $30 (non-member) plus $3.50 for postage and handling. (Order from SME Books, Caller no. D, Littleton, CO 80127, U.S.A.). Reviewer: R.A. Snodgrass The cost and availability of Colombian coal, by Eric D. Jamieson, with the assistance of Kathleen Jamieson. London, lEA Coal Research (14/15 Lower Grosvenor Place, London SWl W OEX). £50 (in member countries), £100 (in non-member countries). Reviewer: W.C. Mather Extraction Metallurgy '85. London, The Institution of Mining and Metallurgy, 1985. £42. Reviewer: R.A. Snodgrass 2. Recent publications Mining annual review 1985. London, Mining Journal, Jun. 1985. 600 pp. £26.50 (surface), £39.50 (air). High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metallurgy, 1985. 593 pp. £27 (members), £30 (non-members). Potential mineral resources of Egypt. 144 pp. US$10. Available from Bendix Field Engineering Corporation-MPGAP, Box 1237, Grand Junction, CO 81502, U.S.A. 3. Mintek reports Report M212 South African costs of equipment for the metallurgical industry (1984). Report M213 The response of as-rolled 3CR12 steel to heat treatment. Report M214 A computer programme for use in the development of multi-element X-ray-fluorescence methods of analysis. Report M221 Commodity profiles for selected metals. Report MIO7D Upgrading of alaskite rock to feldspathic sand. (First issued Jun. 1983; reissued Nov. 1985). IMM awards Given below are details of the trust funds to which applications are invited for grants, etc., payable in 1986. Application forms, which must be returned to the Secretary before 17th March, 1986, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1986