Search Documents

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By C. J. Alberts

The perception exists in many organizations that, once an energy management system is employed, there need not be any further adjustments to such a system. This is not true, as the field of energy management is a dynamic field, and constant feedback and adjustments are needed to enhance the efficiency of a system to the point that substantial pay-back can be obtained. It is stressed that for any energy management system to be successful, careful planning should permeate through the organization, from the top level decision-makers to the workplace. This paper describes a dynamic technique by which energy management strategies can be evaluated by viewing the effects of the strategies on the organization as a whole.

Jan 1, 1997

By H. W. Read

Sustained growth in demand for platinum group metals has resulted in an unfettered increase in new projects undertaken by the platinum producers. These projects are outsourced to various degrees. The argument of this paper is that both the client?s project manager and the consultant?s project manager are essential elements in the successful execution of a project. Their roles are not only different but also complementary, and are defined in the paper. Data gained from considerable experience in the South African corporate mining environment underpins the opinions expressed in the paper. Furthermore, an extensive literary search was undertaken to determine trends in related industries outside the South African context. Throughout the argument it is emphasized that project philosophy emanates from a systems view and must be treated as an overarching whole. The elements of project management become meaningless unless they are connected to one another and integrated into a cohesive unit. Advancing the knowledge field of project management is of critical importance to mining investors. There is no doubt that a key determinant of the sustainability of mining business is closely related to the efficiency of all-inclusive project management. From pre-investment and feasibility studies, implementation and execution, to ramping-up to full production, scientific project management has a critical role to play. Guidelines for the pursuance of this ideal are proposed. The introduction contextualizes the subject matter in an overview of the evolution of mine management in South Africa and abroad. Then, brief insight is given into the philosophy of project management. This exposition is confined to the predispositions, presuppositions and defining characteristics of project management. The core of the paper looks at the roles of the client?s project manager in relation to the consultant?s project manager. This section is underpinned by practical experience gained by the author on numerous mining projects. A view is taken of the future of project management in the mining industry. The conclusion summarizes the argument and aligns project management trends in the mining industry.

Jan 1, 2004

By C. E. Feather, G. M. Koen

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER B.Se. Hons. (Cape Town)* and G. M. KOEN D.Se. (Pretoria)* A description is given of the nature and occurrence of gold at various stages in the process of its recovery from Witwatersrand and related ores. Electron microprobe investigations show that the surface of gold grains in the ore is already coated. During metallurgical processing, further coatings, mainly hydrated iron oxides, accumulate on the grains. Theories are advanced for the formation of these coatings, and the adverse effects on metallurgical operations are discussed.

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

By H. M. Wells

The influence of economics on the design of mine shaft systems by H, M. WEI.LS, Pr. Eng., M.Se. (Fellow) The purpose of this paper is to review some of the more important economic criteria that must be taken into account when planning the number, type, size, and distribution of the shafts, or shaft systems, required to exploit a block of payable ore. The postulated philosophy governing the selection of design parameters is that of optimization of the financial return per rand of venture capital employed for the project as a whole. While this criterion may not necessarily satisfy the investment objective under all circumstances (as, for instance, where risk limitation is important), it does serve to place the relative economic advantages and disadvantages of specific design features, which may sometimes be in opposition, into correct perspective with respect to the overall economics of the project under the prevailing economic climate at the time of the investigation.

The paper discusses some theoretical aspects of Gy's sampling theory and provides reasons as to why it has found limited use in the mining industry, particularly for ores with low concentrations of values such as gold. These types of ores are referred to as low grade ores in the paper. It is shown that the misuse of the a priori liberation factor proposed by Gy is the main reason for the implementation limitation of Gy's model for low-grade ores. In addition, results of a case study done at the Gencor Geostatistics Department based On the new implementation of Gy's theory are provided.

Jan 1, 1996

By FT Cawood

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By R. D. Beck

The minerals industry needs the support of al sections of the population if it is going to be able to supply the new materials required for future development. It will achieve this support only if its image is good. Perceived images of the minerals industry are examined in respect of history, technology, environment, safety, education, and economics. Concern is expressed about the low technological image of the industry and the declining number of students enrolling in minerals-related disciplines. It is concluded that it is the professionals, through institutes like The South African Institute of Mining and Metallurgy, who must take the lead in improving the image of the minerals industry. The Presidential Address gives data to support this thesis; data that, is hoped, can be used in efforts to educate people about the minerals industry.

Jan 1, 1991

By A. J. S. Spearingt

The hydraulic transportation of relatively dense slurries for backfill purposes is typically carried through vertical and horizontal pipelines under gravity. Wear in backfill pipelines has become such a major problem that it is now one of the main reasons for the relatively slow build-up of placed backfill in spite of encouraging performance results in the gold-mining industry. This paper describes tests on pipeline wear that were carried out on classified tailings from the backfill plant at Vaal Reefs East. The testwork was carried out under various conditions of slurry relative density, slurry velocity, and pipeline diameter. Empirical relationships are presented for each transportation and pipeline parameter evaluated and, finally, overall relationships between pipeline conditions and transportation parameters are proposed.

Jan 1, 1992

By Z. T. Bieniawski

Estimating the strength of rock materials by Z. T. BIENIAWSKI, Pr.Eng., D.Sc.(Eng.) (Visitor) A practical approach for estimating the strength behaviour of rock materials is presented. The demand for data on rock properties in engineering design is considered, and it is shown that, based on the trends observed in the South African mining industry during the last twenty years, simple and easy-touse methods for the estimation of the uniaxial and triaxial strength of rock materials are needed. It is shown that the uniaxial compressive strength of rock can be conveniently determined from the pointload strength index, which is obtained underground on unprepared rock cores. The triaxial strength of rock can be estimated for most practical purposes from empirical strength criteria. Two such criteria are proposed that allow estimation of the triaxial strength for rock materials to about 10 per cent. The only input required for these criteria is the uniaxial compressive strength. The validity of the practical approach outlined in this paper is confirmed from the experimental tests conducted on some 700 rock specimens representing five rock types. A practical example for the prediction of rock strength is given.

Jan 3, 1974

By R Kersten

The note describes an exercise on the simulation of the frequency and size of seismic events on the basis of the frequency distribution of the events and their inter-arrival times (Le. the frequency distribution of the time elapsed between events). From the suite of available results, those of one simulation for a period of three months are included. The tentative conclusions drawn from the exercise indicate that the overall seismic activity in an area can be predicted for a time period, that structurally complex areas will have a higher incidence of seismic events than other areas, and that the position and time of an event cannot be predicted by the use of a wide-spread system such as that used at present.

Jan 1, 1985

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

By B. Talbot

How this simple plant generates a large revenue stream. The concept behind the Tailings Scavenging Plant (TSP) is simple: it is a non-complicated modular plant which is designed to be more stable than upstream plants. This, plus the use of ?high energy?, enables the plant to recover any metal missed by the upstream operation. Impala Platinum?Mineral process started pilot plant exercises in June 2003. The pilot plant ran for one year before the capital for the full-scale plant was approved. This year was used to motivate, design and cost a full-scale plant. The metal produced during the pilot and feasibility study enabled this part of the project to run at a small profit. The scale-up to full-scale was relatively simple as the pilot plant had a capacity of 180 m3/hrand the full-scale plant was designed for a capacity of 550 m3/h. The design for the full scale plant was completed in May 2003, with ground breaking taking place on 19 May 2003. The construction phase of the project went well with the commissioning of the first two modules taking place on 22 October 2003. The remaining two modules were commissioned two weeks later. The plant was at full capacity by the 20 November 2003. A review of the plants performance for the first 5 production months is as follows: the plant has required only a few minor modifications and additions, it has run well in excess of 95%availability with no major wear apparent. In addition to this, the plant has produced 3 times the metal forecast.

Jan 1, 2004

By P. M. Vercruijsse

Dredging is an industry in constant transformation. It has changed tremendously in the last decades. The traditional dredging activity, like construction and maintaining ports and harbours, desilting of drainage and irrigation channels, keeping reservoirs at depths and removing sediments from waterways, is still of importance. However, it is surpassed by other applications of dredging technology. Reclamation is an important example, where large amounts of sand are dredged, transported over large distances and used to make new land for industrial, housing, airport and other infrastructural purposes. Beach nourishment and other protective measurements should be mentioned here as well. Other applications like offshore winning of oil and gas, environmental clean-up, mining of interesting minerals like gold, diamonds, titanium and tin as well as aggregates from inland and offshore deposits are of importance. For all of these dredging applications equipment is required, and with changing circumstances and constraints, the design and use altered significantly. Larger dredging depths and increasing capacities require an impressive scale-up of equipment and tools. A demand for higher accuracy and selectivity set the requirement for a higher level of automation and control in combination with a well trained crew. Operations under more difficult circumstances and with other soil characteristics necessitated the development of new dredging components and systems. A sound basis for all developments was and still is a better understanding of the various dredging processes. This paper will highlight some eye-catching developments in the dredging industry. It will focus on issues in the field of hydraulic transport such as ever increasing capacity and dredging depth, as well as the pumping of large size materials.

Jan 1, 2007