Search Documents

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By Dick Minnitt

Large-scale variability in process plants and process control can be identified and controlled through disaggregating the overall variability in a process stream. Conventional statistics and Statistical Process Control (SPC) fail to address the concept of stream heterogeneity, therefore fail to identify and distinguish between the various sources of variability in a process stream. A modified set of 445 data from a process plant is used as an example to explain the benefits of variography in process control. Large-scale variability, usually in the form of product composition cycles and chemical cyclic variations may be manifest throughout a sampling system or a process plant, but this type of variability is most easily discernable in one-dimensional process streams. The Moving Average is a powerful tool for identifying large and small scale variability and cyclical behaviour in process streams, while the variogram is a custom built tool that allows the components of variability to be identified and resolved. The positions in the variogram at which the different variance can be read and the nomenclature of these types of variability is described. The transfer of variances converted to standard deviations to the Control Charts, allows an operator to appreciate the appropriateness of Upper and Lower control and specification limits. The overall contribution of the various sources of variability is represented in a pie diagram.

Jan 1, 2007

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By E. Shavartz, N. B. Strydom

The incorporation of individual cooling in a compressed-oxygen closed-circuit breathing apparatus by E. SHVARTZ, M.Sc. (U.C.L.A.), Ph.D. (U.S.C.) (Visitor) and N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow) A conventional compressed-oxygen breathing apparatus, which did not include provisions for dehumidification of the inspired air at high environmental temperatures, was tested at these temperatures with and without conductive cooling in the form of 2 kg of pre-frozen ice placed inside the breathing bag of the apparatus. The pre-frozen ice provided conductive cooling of the soda lime and of the chest and abdomen of the subject, who performed moderate work at 50,1 "c. Without cooling, the subject was exhausted after 35 minutes because of a wet-bulb temperature of the inspired air of 46"c. With cooling, the subject finished 2 hours of work. This was possible by keeping the soda lime at a relatively Iow temperature, which resulted in a wet-bulb temperature of the inspired air of only 42 °C after 2 hours, and by conductive cooling of the chest, which resulted in the maintenance of a relatively Iow heart rate and rectal temperature.

Jan 7, 1975

By John Freer

On 25th November, 1983, nearly forty members of The South African Institute of Mining and Metallurgy, together with Doris Gardner and Judith Money from Kelvin House, travelled by luxury motor coach to Secunda, there to visit the coal-mining and conversion operations of Sasol Limited.

Jan 1, 1984

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005

By G. Konak

In-pit crusher location selection has had an important role recently, since increasing diesel prices. One way of reducing the haulage costs is to shorten the truck haulage distance by bringing the truck dump point into the pit. This study covers the work done on the optimum crusher location definition for a company that produces aggregate near Izmir, a city of Turkey located in the west. This paper will discuss the effects of pit geometry and mine access requirements on optimum crusher location selection that are mainly based on the establishment of minimum haulage distance. The method will be introduced first and then the computer algorithm developed for this study will be discussed later in the paper. Keywords: in-pit crushing, optimum location selection, optimizing haulage, computer aided design.

Jan 1, 2007

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in 1983 with the formation of DeBeers Marine. Full-scale commercial mining commenced around1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geosurvey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. De Beers operates across the entire value-chain spectrum from geology and geosurvey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in De Beers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities is also available to support R&D and projects activities. Hydrotransport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002

By M. Bryson, V. Deeplaul

As a national facility, Mintek?s brief is to conduct high calibre research that allows the most effective utilization of South African resources. The research takes two different forms, with the efforts being directed at both high-risk endeavours that may lead to the development or adoption of new technologies or the reapplication of technologies to potential new operations. Starting in the 80s Mintek began developing a process to upgrade the UG2 ore and invested heavily in projects, equipment and people to service the industry. Some of the highlights of that work that has been conducted here include: ?Development of a milling and flotation process for UG2 ores ?Development of the ?Mintek Process? for maximizing PGM recovery for UG2 ores ?Conversion of the UG2 milling circuits to open circuit ?Development of a robust pilot plant facility for use in plant design studies ?Use of dense media as a waste rejection option ?Use of attritioners in flotation circuits. More recently, and with the future in mind, the following processes are being researched, some of which have already been commercially applied: ?Development of a flowsheet for Platreef ores ?Use of optical sorting technology for upgrading platinum ores ?Use of a mini-plant for reagent optimization studies. Each of the highlights listed above will be discussed in the paper.

Jan 1, 2004

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By Y. Qin, L. Han, P. Gao, Y. Han, Y. Lia

In the present study, an innovative comminution technology of high-voltage pulse discharge was proposed for galena to weaken the mechanical property. The results of pre-treatment experiments indicated that the optimal operating conditions of spherical gap spacing 25 mm, pulse numbers 120, and loading voltage 25 kV were obtained, where the relative grindability of pretreated products was improved significantly, although with the prolonging of grinding time, the superiority of high-voltage electric pulses was gradually weakened. The galena ores were subjected to a high-voltage pulse discharge, and then the crack generating along the boundary between galena and gangue was observed under an optical microscope, and the surface burning which appeared in the ores. The scanning electron microscope (SEM) results indicated that the pretreated products were in a state of melting and then condensation, accompanied by some pore formation. Pulsed discharge pre-treatment not only produced more micro-cracks and cracks in the sample but also extended the original crack. Keywords: High-voltage pulse discharge; galena; relative grindability; micro-crack

Jan 1, 2020

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012