Search Documents

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By J. Tikka, E. Bäcklund, N. -O. Lindfors

Tornados are the most violent weather events in the world, and we have all seen the forces and phenomena created by tornados in nature. Airgrinder AB has been working with a material treatment technology, which most easily could be described as an artificial tornado. The process consists principally of one air fan providing a high-velocity airstream that enters a mechanical cyclone. When the gas enters the cyclone, an outer vortex is created. This outer vortex rotates next to the cyclone wall, and at the bottom of the cyclone funnel the gas stream is turned and an inner vortex is created. The control of the air flow is tuned by a special device on top of the cyclone. The gas outlet is at the top of the cyclone and the material outlet at the bottom. The material is fed through a feeding device into the air stream channel prior to the inlet into the cyclone. The process is basically an improved grinding and dehydrating system, which is very efficient and environmentally friendly and can even be employed with very sticky materials. Also due to its rotating comminution, the material particles become rounded during grinding, hence more free flowing and easier to handle. MEFOS has already tested more than 30 different applications in the pilot equipment. The materials tested range from metallurgical slags containing 2?3% moisture to sludges with up to70% moisture. This technology has a potentially strong impact on mineral beneficiation, including the drying of sticky fine-grained materials, improved and selective gas scrubbing and the manufacture of free flowing powders.

Jan 1, 2007

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well proven Swiss Tunnel Seismic Prediction System TSP has been substantially augmented for online geological prognosis in underground construction. In its latest version, the Integrated Seismic Imaging System ISIS provides high resolution seismic images of the rock mass around a tunnel face via an array of standard anchor rods. These rods contain 3D-geophones at their tips and can be readily installed during excavation work. A further innovative component of the system is the newly developed high-power repetitive source for application in hard rock: a pneumatic hammer with laser triggering to be mounted on construction machinery. A user-friendly software package permits online data acquisition and processing, 3D-visualization, and a first geological interpretation. Tomographic images of compressional and shear wave velocity fields at fault zones in metamorphic rock of the Gotthard Base Tunnel in the Central Alps are presented. Das langjährig bewährte Schweizer Tunnelseismische Vorauserkundungssystem TSP wurde inzwischen wesentlich weiterentwickelt. In seiner neuen Version, dem Integrierten Seismischen Imaging System ISIS, ermöglicht es hochauflösende seismische Abbildungen des Gebirges im Vorfeld und Umfeld einer Tunnelauffahrung mit Hilfe einer Anordnung von Felsankern, die an ihren Spitzen 3-Komponenten-Geophone enthalten. Eine weitere Neuerung von ISIS ist die pneumatische Hochleistungs-Impulsquelle mit Laser-Triggering. Eine benutzerfreundliche, interaktive Software ermöglicht die online Datenerfassung und -auswertung, 3D-Visualisierung und eine erste geologische Interpretation. Tomografische Abbildungen von Kompressions- und Scherwellengeschwindigkeitsfeldern an Störungszonen in metamorphem Gestein des Gotthard-Basistunnels werden gezeigt. Basé sur de nombreuses années d’expérience, le système suisse, bien établit, de reconnaissance sismique à l’avancement des tunnels (système TSP), a été sensiblement amélioré pour obtenir une prévision géologique en temps réel durant l’avancement de travaux souterrains. Sa dernière version, le Système Intégré d’Imagerie Sismique (ISIS), fournit des images sismiques haute-résolution du massif rocheux à l’avant d’un tunnel grâce à un réseau de tiges d’ancrage standard. Ces tiges, équipées à leur extrémité de géophones 3 composantes, s’installent très aisément durant les travaux d’excavation habituels. Le élément d’innovation récente concern le nouvelle source très répétitive et de forte puissance pour les applications aux roches dures: un marteau pneumatique déclenché par un système à laser. Un ensemble de programmes informatiques convivial permet l’acquisition et le traitement en temps réel des signaux et produit une vue 3D ainsi qu’une première interprétation géologique. Nous présenterons des images de réflexion d’ondes de compression et de cisaillement ainsi que des inversions tomographiques de zones de faille dans des terrains métamorphiques obtenues à l’occasion du creusement du tunnel de base du Gothard, dans les alpes centrales.

Jan 1, 2003

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By J. Werfling, J. R. Kiehl

SUMMARY: The effects of blasting on structures are assessed on the basis of the maximum amplitudes of the occuring vibration velocities. If the standard values in the German Standard DIN 4150 are not exceeded, damages to structures are not to be expected. The estimation of the maximum vibration amplitudes is usually based on experience or on emperical formulae. However, a comparison of expected with measured values shows that these estimations are not conservative, particulary in case of small distances between blasting locations and structures. More reliable predictions are possible on the basis of numerical analyses, which simulate the three-dimensional propagation of waves with consideration of the geomechanical and geometrical conditions. In addition to the expected velocities, these analyses also allow the determination of stresses resulting from dynamic loading. If the dynamic stresses are known, the effects of blasting on structures can be predicted. ZUSAMMENFASSUNG: Die Auswirkungen sprengbedingter Erschütterungen auf bauliche Anlagen werden in der Praxis auf der Grundlage der Maximalamplituden der auftretenden Schwinggeschwindigkeiten beurteilt. In der DIN 4150 werden Anhaltswerte angegeben, bei deren Einhaltung Schäden von Gebäuden nicht zu erwarten sind. Die Abschätzung dieser Schwing-geschwindigkeiten erfolgt meist auf der Grundlage von Erfahrungswerten oder empirischer Formeln. Der Vergleich der prognostizierten Werte mit Meßergebnissen zeigt jedoch, daß diese Ansätze insbesondere dann, wenn die Abstände zwischen den Sprengorten und den Gebäuden gering sind, nicht konservativ sind. Zuverlässigere Prognosen sind auf der Grundlage von numerischen Berechnungen möglich, in denen die räumliche Ausbreitung von Erschütterungen unter Berücksichtigung der geomechanischen und geometrischen Verhältnisse simuliert wird. Mit derartigen Berechnungen können die zu erwartenden Schwinggeschwindigkeiten und die aus der dynamischen Beanspruchung resultierenden Spannungen ermittelt werden. Dies ermöglicht Aussagen über die Auswirkungen sprengbedingter Erschütterungen auf Bauwerke. RÉSUMÉ: Les conséquences de vibrations résultantes d'explosions pour des bâtiments sont estimés dans la pratique à partir des amplitudes maximales des vitesses d'oscillation. Dans la norme allemande DIN 4150 des valeurs d'orientation sont données, avec l'observation desquelles de dommage à des bâtiments n'est pas à présumer. Ces vitesses d'oscillation sont estimés généralement à partir de valeurs d'expérience ou de formules empiriques. La comparaison des valeurs prédits avec des résultats de mesures montre cependant que ces hypothèses ne sont pas conservateurs, en particulier si les distances entre les lieux de sautage et les bâtiments sont petites. Des prédictions plus fiables sont possibles à partir de calculs numériques, dans lesquelles la dissipation spatiale de vibrations est simulée en considération de la situation géoméchanique et géométrique. Avec tels calculs les vitesses de vibration à présumer et les contraintes résultantes de l'effort dynamique peuvent être établies. Cela permet de constater sur les conséquences de vibrations résultantes d'explosions pour des bâtiments.

Jan 1, 2003

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

By D. F. Malan, U. Du Preez, P. S. Heyns

South Africa has two main platinum reef deposits, namely the Merensky reef and the UG2 reef. These reefs are currently mined using traditional drilling and blasting methods. Mechanized cutting could potentially enable continuous mining, which would offer significant advantages. This would require thorough understanding of the cutability of the rock. To explore this, a linear cutting machine was developed to conduct laboratory scale cutting tests. This work describes the development and commissioning of the cutting machine using sandstone, as well as subsequent characterization tests on UG2 reef samples. UG2 reef has large variability in strength on a millimeter scale. This introduces uncertainty in the test results due to added variance from one cut to the next for the same UG2 reef sample. Another problem is the variability in rock properties of the UG2 reef, when testing samples from different mines. The cutting tests led to fine fragmentation, which is known to be a significant problem for cleaning operations in underground stopes and warrants further research. A finite element method simulation of the rock cutting was conducted using ANSYS LS-DYNA and the continuous surface cap model to simulate rock cutting in the UG2 reef. It was found that it is possible to use LS-DYNA with the continuous surface cap model to model rock cutting of UG2 reef and get acceptable results, but the user must calibrate the model parameters using the experimental results. Therefore, the model is only fit for one set of cutting parameters and further work is required to generalize results.

Nov 27, 2024

By S. Konetschnik, E. Dreyer, A. Filzwieser

"More intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetimes, making cooling technology an important aspect of furnace operations. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start-up and operation, namely hydration problems, corrosion, and explosions. Apart from these aspects, the energy that is removed by extensive cooling cannot be recovered and is normally lost in the cooling towers.With METTOP’s new patented cooling technology it is possible to overcome the disadvantages of water by using an alternative cooling medium, namely ionic liquids (ILs). The main advantage of ILs is the fact that there is no risk of explosion should this liquid come in contact with molten metal. Furthermore, ILs can be used at higher temperatures than water - up to 200°C. This relatively high cooling medium temperature avoids hydration and corrosion problems and allows recovery of the energy by combining the ILTEC system and the organic Rankine Cycle (ORC) technology, for example.Due to the removal of the explosion risk, much higher safety standards can be achieved, particularly in critical areas such as tap-holes"

Jan 1, 2014

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By M. I. Mthenjane

"BackgroundThe paper discusses post-mining land use however, the essence of the topic is the emotional motivation behind the decisions related to mining investment and development. Therefore this is not a typical SAIMM technical paper about the science and techniques of post-mining land use. There are already numerous papers written and conferences held on this aspect of post-mine land use; the science is well understood, but the evidence of the practical application of the (environmental, social, and economic) science is sparse. At a recent conference held in November 2017 on the theme of ‘Science, Business, Society Dialogue – linking science, society, business and policy for the sustainable use of abandoned mines in the SADC region’, it was demonstrated through the delivery of several papers on the possible viable options of post-mine land use. The conference was structured in nine sessions, covering the following relevant topics:? Sessions 1 and 2: Nature and magnitude of the problem: raising awareness? Sessions 3 and 4: International experiences in remediation: case studies? Sessions 5, 6 and, 7: Technological solutions: converting liabilities into assets? Session 8: Implementing solutions: social and legal aspects? Session 9: Wrap up, lessons learned: conference resolution.Summaries of the key outcomes of the sessions are available for reference.The aim of this paper, accompanied by the video speech, is to provide a visualization of the possibilities of post-mine land use. Mining contributes approximately 7% to South Africa’s GDP - this is the lowest it has ever been and is attributable to both a diversifying economy and to poor mining and investment policy which has resulted in reduced investment in the sector. The objective of the paper is to highlight the opportunities, for succeeding and diversifying economic activity following mining and mineral extraction which can continue to sustain the livelihoods and wellbeing of communities and societies beyond mining.During mining, very few alternative and local economies develop. Dependence on mining and its value chain prevails until mining ceases. This idea is conveyed in Figures 1a and b."

Jul 1, 2019

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

By J. Maritz, K. de Beer, S. M. Buthelezi

The economic upheaval of COVID-19 forced companies to invest in emerging technologies to aid recovery. One such technology is extended reality, which is becoming a mature and innovative tool. Early adopters are seeing significant benefits in learning, training, immersive data visualization, and remote assistance. In South Africa, the mining industry is increasingly interested in using extended reality to optimize and innovate operations. The Minerals Council of South Africa's July 2021 report highlighted the potential of extended reality's to achieve zero-harm production and modernize the industry. However, the extent of extended reality adoption in mining remains unclear due to limited information on its usage. This study addressed this gap by distributing an online survey to assess awareness, knowledge, and current uses of extended reality in South Africa’s mining sector. The results indicated that virtual and augmented reality had the highest levels of awareness and usage, primarily for learning and training. Mixed reality, however, had the lowest awareness and knowledge levels. In terms of applications, visualization and remote assistance had the least use cases. These findings highlight that the South African mining industry is deficient in its understanding and use of extended reality technologies. Without better awareness and application, the South African industry risks missing out on the full benefits of extended reality. The study underlines the need for the South African mining industry to improve its outlook on extended reality technologies to fully leverage their potential applications and benefits.

Jul 10, 2024

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By C. W. Siyasiya, K. A. Annan, W. E. Stumpf

"SynopsisThe relationship between niobium content and austenite grain growth has been investigated through hot rolling simulation on a Bähr dilatometer. The effect of delay time between passes during rough rolling in Nbmicroalloyed steels with nitrogen contents typical for electric arc furnace (EAF) melting was studied. The results indicate that the grain growth constants n, Q, and A increase with an increase in Nb content. The activation energy for austenite grain growth Q was found to be in the range of 239 to 572 kJ/mol, the exponential constant n ranged from 2.8 to 6.2, and the material and processing condition constant A from 4.24 × 1012 to 4.96 × 1028, for steels with niobium contents ranging from 0.002% Nb to 0.1% Nb. A general constitutive equation for the prediction of austenite grain growth in these Nb-microalloyed steels under rough rolling conditions has been developed. Good agreement between the experimental and the predicted values was achieved with this constitutive equation.IntroductionGrain refinement has been found to increase both the strength and toughness of steels (Gao and Baker, 1998; Sharma, Lakshmanan, and Kirkaldy, 1984; Seok et al., 2014; Maalekian et al., 2012). It is also known that the austenite grain size directly influences the microstructure, and thus the mechanical properties, of the steel (Maalekian et al., 2012; Yue et al., 2010). Effective grain growth control is reported to be achieved through addition of precipitate-forming elements, such as Nb that, slow down the grain boundary migration through pinning and solute drag mechanisms (Yu et al., 2010; Olasolo et al., 2011; Alogab et al., 2007). Much work has been carried out on austenite grain lsize control by the addition of precipitate-forming elements that have a strong affinity for interstitial elements, such as carbon and nitrogen, which form the dispersed pinning particles to inhibit the austenite grain growth (Alogab et al. 2007; Hodgson and Gibbs, 1992; Nanba et al., 2003; Flores and Martinez, 1997; Rollett, Srolovitz and Anderson, 1989). Austenite grain growth can be described using a conventional or a modelling approach. With conventional approaches (e.g. metallography), in-situ monitoring of austenite grain growth at high temperatures is impossible. Modelling the grain growth behaviour based on available data is the ideal option. To quantitatively describe austenite grain growth therefore requires development of a sound mathematical austenite grain growth equation that accounts for the effects of the varying microalloying elements in inhibiting austenite grain growth. Numerous attempts have been made to develop an empirical model based on the general equation developed by Sellars and Whiteman (1979). Many of these models do not account for the direct effects of the microalloying elements such as Nb in austenite grain growth control [Fu et al., 2011; Wang and Wang, 2008; Wang et al., 2006; Shanmugama et al., 2005; Banerjee et al., 2010; Pous-Romeroa et al., 2013). The current work has considered this limitation, taking into account the direct effect of niobium in grain growth control during thermal processing. This is done by incorporating the initial austenite grain size Do and the microalloying element niobium in the development of a constitutive equation for grain growth prediction in Nb-containing microalloyed steels."

Jan 1, 2015