Search Documents

By A. J. Jager, J. A. Ryder, M. U. Ozbay

This paper deals with procedures used for designing pillar systems in hard-rock tabular mines operating at shallow depths, typically less than 1000 m. A comprehensive review if current practice identifies four types if pillars, namely non-yield, yield, crush and barrier pillars, and the main principles for designing these pillars are outlined. It is shown that the current design methods for pillar systems in South Africa are mainly empirical, each mine developing its pillar-design methods based largely on practical experience. This results in varying pillar layouts, even between neighbouring mines, despite similarities in geology, and depth if mining. It is suggested that some current layouts may fall short if being the best as regards safety, the maximum safe extraction percentages, or flexibility in accommodating future mining scenarios in deeper or otherwise different geological conditions.

Jan 1, 1995

By M. du Plessis, D. F. Malan

"The aim of any mine design is to ensure that the excavations remain stable for the period they will be in use. Various pillar systems are used to ensure that underground stopes remain stable and that mining activities do not affect the surface infrastructure through either surface subsidence or seismicity. Intermediate-depth platinum mines make use of in-stope pillars designed to fail while the pillars are being cut at the mining face. The pillar stress exceeds the loading capacity and the pillars crush as a result. The aim of the paper is to provide an overview of in-stope crush pillars. This will include the application, behaviour, function, mechanism, impact, and design of a crush pillar system."

Jan 1, 2015

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By H. Cevizci

In this study, a newly developed plaster stemming method is studied and compared with the usual dry drill cuttings stemming method for surface blasting in mines and quarries. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. In one series of blast tests, blasting costs per unit volume of rock were reduced to 16 per cent by increasing burden and spacing distances. Also, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments reduced to 5.4 per cent of the total, compared to 37.7 per cent in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage, but these increased values were small and under the permitted limit for blast damage criteria.

Jan 1, 2012

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

By M. J. Sapko

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL's Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal's ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Jan 1, 2003

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Flotation columns are normally operated at optimal superficial gas velocities to maintain bubbly flow conditions. However, with increasing superficial gas velocity, loss of bubbly flow may occur with adverse effects on column performance. It is therefore important to identify the maximum superficial gas velocity above which loss of bubbly flow occurs. The maximum superficial gas velocity is usually obtained from a gas holdup versus superficial gas velocity plot in which the linear portion of the graph represents bubbly flow while deviation from the linear relationship indicates a change from the bubbly flow to the churn-turbulent regime. However, this method is difficult to use when the transition from bubbly flow to churn-turbulent flow is gradual, as happens in the presence of frothers. We present two alternative methods in which the flow regime in the column is distinguished by means of radial gas holdup profiles and gas holdup versus time graphs obtained from CFD simulations. Bubbly flow was characterized by saddle-shaped profiles with three distinct peaks, or saddle-shaped profiles with two near-wall peaks and a central minimum, or flat profiles with intermediate features between saddle and parabolic gas holdup profiles. The transition regime was gradual and characterized by flat to parabolic gas holdup profiles that become steeper with increasing superficial gas velocity. The churn-turbulent flow was distinguished by steep parabolic radial gas holdup profiles. Gas holdup versus time graphs were also used to define flow regimes with a constant gas holdup indicating bubbly flow, while wide gas holdup variations indicate churn-turbulent flow. IntroductionTwo types of flow can be distinguished in gasliquid flows in bubble columns: bubbly flow and churn-turbulent flow. The bubbly flow regime is characterized by uniform flow of bubbles of uniform size. Churn-turbulent flow, on the other hand, is characterized by a wide variation in bubble sizes with large bubbles rising rapidly and causing liquid circulation.Flotation columns are normally operated in the bubbly flow regime, which is the optimal condition for column flotation (Finch and Dobby, 1990; Yianatos and Finch, 1990; Ityokumbul, 1992). However, it has been generally observed that flotation column performance deteriorates when the superficial gas velocity is increased beyond a certain limit where the flow regime changes from bubbly flow to churn-turbulent flow (Xu, Finch, and Uribe-Salas, 1991). The identification of this critical or maximum superficial gas velocity is therefore important for optimal operation of flotation columns."

Feb 1, 2019

By T. N. Moore, E. M. De Souza

This paper details a study conducted in Canada on the use of a drill with two different types of elastomer-covered handles in place of the standard steel handles. One type of handle was covered with a relatively stiff elastomer with a durometer of 70 (referred to as the plastic handle), and the other was covered with a more compliant elastomer with a durometer of 56 (refered to as the rubber handle). It was found that, compared with the steel handle, the overall acceleration at the interface between the plastic handle and the drill operator's hand was 2,5 times less, and that between the rubber handle and his hand was 3 times less. This reduction occurred predominantly in the frequency range above 500 Hz, and was greater with increasing frequency. However, an analysis based on the methodology of an international standard (which places greater importance on low-frequency vibration), indicated that the reduction in vibration levels was minimal. ~he driller himself felt that operation with the plastic and rubber handles was more comfortable, the rubber handle being preferred.

Jan 1, 1991

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4 (the main product) and other waste metal chlorides. The TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amount of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify effects of using different feedstocks.

Jan 1, 2015

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By W. K. Loftus, H. S. Simpson

Discussion I. R. M. Cheston (Visitor): I should like to congratulate the authors on this interesting paper which graphically illustrates the overall effects of the gradual developments in diamond concentrating processes which have taken place over the past few years. These final stages of diamond concentration represent only a minor factor in the cost of diamond production but because of the shortage of highly trained people for this work, any easing of the burden on the sorting staff has an importance far beyond the immediate economic sphere. The search for the solution of problems posed by the economic and social conditions of industry is never-ending. The Diamond Research Laboratory is, even now, carrying out further work to improve still more the operation of general diamond recovery processes as described in the paper. Before looking at some of the latest developments in this field of final recovery, there are a few points arising from the paper on which I would like to comment. On page 321, reference is made to the X-ray sorters originally developed by the DRL. The paper gives a figure of 100 per cent recovery of diamonds from +7 mesh concentrates in two passes through the prototype machine. Not wishing to claim miraculous powers for our group, I would prefer to see this given as virtually 100 per cent recovery of all fluorescing diamonds. Firstly however much care is taken, there is bound to be an occasional operating loss. In the test work, 100 per cent recovery was made on many occasions but this was not always so. Secondly, although most diamonds fluoresce strongly under X-rays, some diamonds only fluoresce weakly. Type IIB diamonds, in fact hardly fluoresce at all, but the incidence of this special type of diamond is very low in most deposits. However, in operating the commercial X-ray machines, there is a certain background level of reflected radiation from other feed particles. Unless the diamond fluorescence is several times greater than this, it is not possible to achieve sufficient sensitivity in ejection. A certain small but variable proportion of diamonds from each deposit is always found to fluoresce too weakly to be recovered by the X-ray machine. Tests have shown, that for the De Beers mines, this proportion is considerably less than I per cent. These diamonds are nearly all dark brown or black in colour and therefore of low value. The degree of fluorescence does not, however, depend entirely on the colour or quality of the diamond and some of the brightest fluorescence comes from the lowest quality of boart diamonds. Investigations into the property of the diamond which causes this low fluorescence are being carried out. On page 322 it is suggested that zircon fluoresces in the same colour spectrum as the diamond. This is not quite accurate. The total light given out by zircon under X-rays is of the same order as that of diamond. However the zircon radiation has a much wider spectrum band than the diamond fluorescence. Reference is also made on page 322 to the effect of selective milling in small laboratory mills on diamonds. Perfect diamonds are very hard and very strong and are extremely difficult to break. Imperfect diamonds, which form the majority of diamonds recovered from most deposits, although hard, can be very brittle. Even under slight impact some of these diamonds may shatter to powder. Milling conditions must therefore be extremely closely controlled to minimize breakage, and even so, some breakage will always occur. As suggested in the paper, the necessary conditions are: the use of small balls, slow speed mills and very limited water addition. Tests elsewhere have suggested that the water content of the pulp in such a mill must be less than 25 per cent by weight of pulp to prevent diamond breakage reaching significant proportions. The skin flotation techniques described on page 323 operate on a very small scale. It is of interest to note that in West Africa a large-scale continuous skin flotation machine is used to recover the fine diamonds. In this operation the feed is dried and, after standing, is mixed with water and fed in a single layer onto a woven phosphor-bronze conveyor belt. This belt runs at a shallow angle into a water bath and as the particles are carried through the air-water-interface, the diamonds float off and over a weir into a collecting box. The bulk of the particles, being wettable, sink to the bottom of the tank and are continuously removed. If treated without prior drying, the diamond recovery is poor. If material is treated immediately after drying, a lot of the gangue particles also float. During standing, in the hot and humid atmosphere of West Africa, it is found that the gangue particles recover their wettability much faster than the diamond particles. Optimum selectivity is obtained after standing for approximately 24 hours. At the DRL we have been experimenting with optical filters to differentiate between the fluorescence of diamonds and zircon. By limiting the light transmission to the fairly narrow range emitted by diamonds, it is

Jan 4, 1970

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

By A. Ball

This paper addresses the need for a unifying model that will permit the selection and design of optimum materials for a given wear situation. With this objective in view, the characteristics of the various forms of abrasive, adhesive, and erosive wear are described in terms of localized stress, strain, strain rate, and frictional heating. The measured performance of a variety of metallic, ceramic, and polymeric materials and coated or surface treated materials are described briefly. These results were obtained under conditions of dry-particle abrasion, abrasion in conjunction with corrosion, cavitation erosion in liquids, erosion by particles in low- and high-velocity gas streams, and erosion by particles in a liquid stream. Electron microscopy was used extensively, together with microhardness profiles, in the determination of the modes of material detachment and the underlying deformations and structural changes. As a result of the experimental work, a model based upon a critical strain to microfracture is presented. The microstructural features and materials properties that determine wear resistance are discussed.

Jan 1, 1986

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006