Search Documents

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By C. H. Johannes, N. B. Strydom, C. H. Van Graan, J. G. A. Van Heerden

Note: The practical application of microclimate cooling in an underground stope in a gold mine by C. H. JOHANNES, C. H. VAN GRAAN, N. B. STRYDOM and J. G. A. VAN HEERDEN INTRODUCTION Although much information was available on the use of pre-frozen jackets as micro climate coolers in underground situations!, 2, no information was available on their performance under practical conditions in stopes. The objectives of this study were. O.F .S. Branch Minutes of the General Meeting held in the upstairs lounge at the Harmony Country Club, Harmony G.M. Co. limited, on Wednesday 12th November, 1975 at 4.00 p.m. NIM reports Report no. 343 A mineralogical investigation of gold-bearing sulphidic ore from the Florence-Devonian Mine, Barberton.(20th May, 1968; re-issued Dec. 1975). Report no. 1384 . Flotation tests on samples of Canadian copper-zinc ores. (12th Nov., 1971; re-issued Nov. 1975). The results are given of laboratory Report no. 1488 Extraction of rutile from Highveld smelter slags. (28th Sep., 1972; re. issued Nov., 1975). Report no. 1499 The production of medium -carbon ferrochromi'um. (4th Dec., 1972; reissued Nov. 1975). Report no. 1521 The dissipation of electrical power in the burden of a submerged-arc furnace. (15th Feb., 1973; re-issued Nov. 1975). Report no. 1527 The physicochemical properties of slags associated with the smelting of nickel sulphide concentrates. (21st Feb., 1973; re-issued Nov. 1975). Report no. 1544 The recovery of salable ferrochromium from material discarded by Ferrometals Limited. (11th Jun., 1973; re-issued Nov. 1975). Report no. 1547 Physicochemical and thermodynamic properties of slags in the system MgO-AlOl.5SiO2. (23rd Aug., 1973; re-issued Nov. 1975). Report no. 1548 Physicochemical properties of slags in the system MgO-Al2O3-SiO2 and their application to the technology of ferro-alloy smelting. (13th Jul., 1973; re-issued Nov. 1975). Report no. 1553 Characterization of the flotation properties of fluorspar from smallscale batch and pilotplant tests. (27th Sep., 1973; re-issued Nov. 1975). Report no. 1555 The analysis, by atomic-absorption spectrophotometry, of matte-leach residues. (2nd Oct., 1973; re-issued Nov. 1975). Report no. 1590 The separation of osmium from ruthenium in hydrochloric acid solutions. (18th Jan., 1974; re-issued Oct. 1975.) Report no. 1606 The electrical-resistance characteristics of the charge in the electric reduction furnace. (1st Feb., 1974; re-issued Oct. 1975). Report no. 1622 The electrical conductivity of the charge in a ferrosilicon furnace. (2nd Apr., 1974; reissued Oct. 1975).

Jan 3, 1976

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

Outsourcing of specialist and non-continuous services is common practice in international mining operations. There is an increasing trend towards this practice in South Africa as a result of the major organisational changes that have taken place in the industry, and as lower revenues and production cost pressures have reduced profit margins. Many specialist functions have been outsourced in the industry for a long time, an example being shaft sinking, which is undertaken by specialist shaft sinking contractors. In the professional services area, some activities have been outsourced, for example the design and construction supervision of tailings dams, but mining related activities such as geology, mine planning and scheduling, engineering, ventilation, and rock engineering, have traditionally been carried out by in-house staff. In this paper some of the industry problems which have led to an increase in outsourcing of professional services are considered. Then the pros and cons of outsourcing are dealt with before outlining the factors which should be taken into account in choosing an outsourcing partner.

Jan 1, 1999

By P. A. Roberts

A modified in situ leaching method for extracting gold from oxidized gold ores using a non cyanide lixiviant is proposed. A non cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide bearing solutions into the subsurface. Oxidized gold ores are the initial focus because earlier research on the use of sodium thiosulphate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulphate breakdown. A reconnaissance research programme, involving ore characterization and hydrometallurgical testwork on samples from four Australian ore deposits and preliminary reactive transport modelling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulphate and ferric EDTA, and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples under anaerobic conditions. The ore characterization and reactive transport studies, suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Physical permeability enhancement could be achieved by blasting and/or hydraulic fracturing of the ore. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in place leaching? has been adopted for the proposed gold extraction system

Jan 1, 2009

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004

By Bjørn Nilsen, Brian J. Ballou

The Tellnes open pit mine in Southwestern Norway has been operating since 1960. The maximum height of pit walls is currently about 150 meters with the current mine plan extending this distance to 400 meters with slope stability being a major controlling factor. As a result of unfavorable combinations of directions of major joints and faults, local stability problems have occurred several places in the pits walls. Stability problems have affected the reliability of main transport roads on several occasions. Most of such incidents have occurred during heavy rainstorms and during periods of repeated freezing/thawing. This paper reviews some of the stability problems and the measures taken to deal with such stability problems.

Jan 1, 2006

By J. Ojeda, R. Kuyvenhoven, M. Ziemski M

This paper focusses on the identification of operational opportunities in a 1100 tph pellet plant to reduce the specific energy consumption in its comminution circuit, which is designed to process magnetite ore and produce pellets to be used as raw material in the iron and steel industry. The assessment is carried out through a frequency analysis for three of the four processing lines of the plant, consisting of one ball mill each with an installed power of 4.5 MW and 280 tph of mill throughput design capacity. The methodology, as described in this paper, facilitates the visualisation and quantification of plant performance and provides a good first approach to prioritise alternatives for optimisation. In a pellet plant, grinding is a critical stage due to its high energy consumption and its major impact on the physical properties of the iron pellets, which quality depends to a large extent on grind size and Blaine index. From the evaluation that was performed it can be concluded that production line 2 has the lowest specific energy consumption of 15.1 kWh/t, while line 1 has the highest with an average of 16.6 kWh/t for the same type of ore. On the basis of the results and current operational practices, it is recommended to increase the average mill throughput from 240 tph to 265 tph, translating into specific energy reduction of 10%, without affecting the chemical and physical properties of the final product. The implementation of an HPGR for regrinding the magnetic concentrate is proposed to assure adequate specific surface area in case grinding coarser becomes an alternative, which would also be beneficial for the subsequent water recovery stages. Keywords: Iron ore pelletisation, grinding circuit, energy efficiency, particle size, frequency analysis

Jan 1, 2020

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognized and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economic restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist about application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2007

In recent years several mine researchers have studied the optimization of cutoff grade with the purpose of maximizing Net Present Value (NPV). The best and most popular one is the Lane algorithm. Based upon the Lane algorithm it is possible to calculate the optimum cutoff grade for mine, mill, and refinery capacities for single metal deposits with variable grades. The Lane algorithm cannot be used in multiple metal deposits. The reason is that, while in single metal deposits six points are possible candidates for the optimum cutoff grade, in multiple metal deposits an infinite number points are possible candidates for the optimum cutoff grades and objective function evaluation of these infinite points is impossible. In this study the Golden Section search method was used to calculate optimum cutoff grades of multiple metal deposits for the same conditions as Lane assumed in single metal deposits. Based on this method, grade-tonnage distribution uncertainty space of problem is guessed. In the next step, by selecting test points in uncertainty space and evaluating the objective function at these points, a part of uncertainty space will be eliminated. The procedure is then repeated until the uncertainty space has been sufficiently reduced to ensure that the optimum cutoff grades have been located to the required accuracy. Key words: Optimum cutoff grades, Optimization, Net Present Value (NPV), Golden Section search method

Jan 1, 2003