Search Documents

By R. H. Estrada-Ruiz

This work analyses a new approach to estimates bubble size distribution of froth surfaces using artificial neural networks (ANN).Also, the robustness of ANN to interpret images with illumination perturbations, produced by light problems or dirt attached to the window of the video camera is evaluated. The experimental work was carried out in a laboratory flotation column, instrumented with an image acquisition system. The images were processed making use of a perceptron model with a hidden layer, sigmoidal transfer function and unitary bias, and the ANN trained with a back propagation algorithm. The results of validation show that ANN are reliable for learning and producing generalized predictions of the froth mean bubble diameter and bubble size distribution, when the model is trained using a database that contains information on the illumination intensity. Keywords: image analysis, neural networks, bubble diameter, bubble size distribution.

Jan 1, 2009

By S. M. Bradshaw

The principles of microwave heating are discussed with reference to dielectric properties, heating phenomena and microwave equipment. Microwave regeneration of granular activated carbon for the carbon-in-pulp process is examined on a laboratory scale, with special attention being given to highlight the problem areas and specific considerations related to microwave heating. Results indicate that microwave regeneration of carbon with 40% moisture on a wet basis by heating to 650°C with steam addition regenerates the carbon to virgin carbon activity levels but with a higher abrasion resistance. A preliminary economic assessment showed that the capital cost for 120 kg/h microwave unit would be R540 000 with an annual operating cost of R 320/t carbon. These figures yield a return on investment of 12%. The aim of this paper is to provide an introduction to microwave heating and to illustrate its application to the microwave regeneration of granular activated carbon for the carbon-in-pulp (CIP) process.

Jan 1, 1998

By G. Raspa

The paper describes a computer procedure for evaluating and selecting recoverable reserves in a mine worked by sublevel stoping. The boundaries of the volume to be mined are optimally defined by means of the 3-dimensional Lerchs-Grossmann algorithm, separately applied to both sides of the panels. The procedure, which has been developed for Masua Mine (Sardinia), also provides for smoothing the optimized boundaries, positioning the drilling drifts, interactive design of drilling fans and calculation of tonnage and grade of each volley. These tonnages and grades form the input of another procedure evolved for production planning.

Jan 1, 1987

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By Hao Li, Allan Moss, Richard K. Brummer

At the Palabora Mine, the transition to caving 400 m below the bottom of the 800 m deep pit resulted in a slope failure of the North wall that began in 2003, and is still mobile. This failure can be explained by the daylighting into the cave zone of a prominent joint set. The failure was modelled by the 3-dimensional code 3DEC, which is capable of modelling the nonlinear behaviour of discontinuum materials with large displacement.

Jan 1, 2006

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

By L. S. Jeffrey

Estimates for South Africa?s coal recoverable reserves made in 1999range from nine to 59 billion tons; latest estimates by the Minerals Bureau suggest that 33 billion tons is a more likely figure. As much as 70% of that coal is located in the Waterberg, Witbank, and Highveld coalfields, as well as lesser amounts in the Ermelo, Free State and Springbok Flats coalfields. However, the Witbank and Highveld coalfields are approaching exhaustion (estimated 9 billion tons of recoverable coal remaining in each), while the coal quality or mining conditions in the Waterberg, Free State and Springbok Flats coalfields are significant barriers to immediate, conventional exploitation. New extraction technologies, technologies exploiting the energy content of the coal in situ, as well as suitable uses and markets for low-grade, high-ash coal are required before the country can utilize its admittedly vast coal resources. Major challenges for exploiting some Limpopo province coalfields are severe water shortages, insufficiently developed infrastructure, fragile environments and poor roof conditions due to the depth and complex geology. In the Central Basin (Witbank, Highveld and Ermelo coalfields) technical innovations for thin seam extraction, economic mining of both pillar coal and intrusion-fragmented resource blocks and the utilization of lower-grade coals are required. The success of the fluidized bed combustion technology is necessary to utilize the low-grade coals of the Free State and Molteno coalfields, while environmental exemption for past problems, together with strategies for mining small, disjointed thin-seam resource blocks, is required in KwaZulu-Natal. Clean coal technologies, coal cost and quality, environmental considerations, sustainable development, the growth of the South African economy and Government?s regulation of the electricity industry are the main challenges to the continued use of coal as South Africa?s primary energy source.

Jan 1, 2005

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By N. Mulaudzi, S. Archer

"Direct cobalt electrowinning was developed to produce unrefined cobalt metal as an alternative to producing a mixed hydroxide product (MHP), which is the common cobalt intermediate product in African Copperbelt operations. MHP is preferred due to the high cost of producing high-grade cobalt cathode. Direct cobalt electrowinning test work results have shown that the purity of the unrefined cobalt metal produced from a low-grade copper solvent-extraction raffinate stream was ~97% (w/w), which is significantly higher than the MHP purity (up to 45% (w/w) Co). The current study investigates whether direct cobalt electrowinning would increase the profitability of African Copperbelt copper–cobalt oxide operations, when compared with the MHP flowsheet. An order-of-magnitude economic evaluation was conducted using dynamic differential discounted cash flow models on a “bare-bones” basis, using a 10% discount rate. Three variables were evaluated, namely; reagent utilisation extents, precipitation extents and filter-press wash efficiency. Multivariable risk analysis was also conducted using the Monte Carlo simulation technique to understand the impact of key project drivers. The financial study results indicated that a direct cobalt electrowinning flowsheet could potentially result in a higher mean net present value (NPV) compared with the MHP flowsheet. Cobalt recovery was found to have the most significant impact on the NPV. In addition to increased profitability of African Copperbelt operations, direct cobalt electrowinning has the potential to reduce the environmental footprint of operations as well as addressing the Democratic Republic of Congo government’s drive towards export of higher value metal products instead of low-grade intermediates."

Jan 1, 2015

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By J. D. Steenkamp, G. E. Williams

Keywords: Ilmenite, titania slag, pig iron, rutile, zircon Located on the eastern shores of South Africa, 180 km north of Durban, Richards Bay Minerals (RBM) produces approximately 2.0 million metric tonnes of product annually making RBM a leading producer of titania slag, high purity pig iron, rutile and zircon. Heavy minerals are extracted from the nearby dunes by dredging and concentration on a floating gravity separation plant, followed by separation of the ilmenite, rutile and zircon at the mineral separation plant located at the smelter site. The ilmenite is processed through an oxidizing roast followed by magnetic separation and is then partially reduced to an 85 per cent TiO2 slag in one of four six-in-line a.c. electric arc furnaces. The slag is milled and then classified into two product sizes suitable as a raw material for both the sulphate and chloride pigment processes. The high quality iron produced during the reduction process is further processed to produce various grades of low-manganese iron. Around 95 per cent of the products are exported, yielding a world market share of about 25 per cent of titania slag, rutile, high quality pig iron, and zircon.

Jan 1, 2006