Search Documents

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By A. Whillier

Note: Hydraulic rock drills and their effect on the underground environment by A. WHILLIER, Pr. Eng Se. D., (M.tT.) (Fellow) In any situation where hydraulic rockdrills are used underground, it is evident that an amount of heat equivalent to the total electric input to the power pack would enter the ventilation air. Book review Australian Mineral Industry 1972 Review. Australia, Department of Minerals and Energy. NIM report Report no. 1691 The determination of zirconium and aluminium by 14MeV neutronactivation analysis. Automation in Mining, Mineral, and Metal Processing The International Federation of Automatic Control (IF AC) is to hold its second symposium on the above subject in Johannesburg on 13th to 17th September, 1976. V Simposio de Mineracao A symposium is being arranged for 6th to 9th August, 1975, in Ouro Preto, Brazil. ACHEMA 1976 The 18th Chcmical Engineering Exhibition-Congress and European Meeting of Chemical Engineering will be held in Frankfurt from 20th to 26th June, 1976, and thc Chemical Engineering World Congress Sixth Underwater Mining Institute The above Institute will be held on the main campus of the University of Wisconsin in Madison, U.S.A., on 2nd and 3rd October, 1975.

Jan 4, 1975

By L. A. Vermeulen, D. D. Howat

A study was made of the performance of a rod mil operating without liter bars and with different arrangements of liter bars in the lining. . The results show that striking improvements in performance, increased throughput, and reduced consumption of liner metal and electrical energy can be obtained by a change in the geometry of the liter-bar arrangements within a mil. Rod mils of equal size fitted with the same arrangement of liter bars but operating at different speeds presented apparent anomalies in the relative consumption efficiency of electrical energy for the production of material smaller than 75 µ m. Marked savings in the consumption of liner metal were achieved by the use of an arrangement of alternating lines of higher and lower liter bars. A study of the relative performances of two large tube mils showed that the use of liter bars in one of the mils resulted in a marked reduction in the consumption of liner metal and electrical energy per ton of material smaller than 75 µ m in the product.

Jan 1, 1986

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By D. C. Krige

The estimation of the tonnage and grade of payable ore in a mine and the correct policy of selective mining based on such estimates, is of vital importance to the mining engineer it is surprising, therefore, that more attention has not been devoted on the Witwatersrand to the scientific improvement of mine valuation methods. At present these methods consist almost entirely of the application of simple arithmetic and empirical formulae guided by practical experience, and ignore the many advantages to be gained from a careful statistical analysis of the behaviour of the gold values. The science of statistics has expanded rapidly during the last two decades and its value as a powerful and indispensable tool is now recognized not only by research workers and scientists but also, ever-increasingly, by the commercial and industrial world. This being the case it is noteworthy that in a mining field such as the Rand with its highly developed and advanced mining methods, singularly little attention has been paid to the analysis of mine valuation problems on a modern statistical basis. This omission is even more striking when cognizance is taken of the wealth of sampling data concerning the gold ore which is available and of the far-reaching decisions and deductions constantly being based on such data. Some contributions have however been made from time to time towards the application of statistics to mine valuation on the Rand (References Nos. 7, 8, 9, 11, and 12), but none of these have been generally applied in practice and a systematic practical approach based on clearly deemed fundamental concepts still appears to be lacking. The object of this paper is, therefore, to define these statistical concepts and to indicate briefly the lines along which statistical methods can be applied profitability in solving some of the existing problems and in improving the general standard of mine valuation on the Rand For this purpose a knowledge of mathematical statistics is essential, but as this paper is primarily intended to provide the mine valuator with a practical introduction to statistical application in his field, the mathematics is confined to a short annexure, together with references from which details can be obtained.

Jan 1, 1994

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By T. T. Chiweshe, L. S. Mokhahlane, M. Welman-Purchase

This study examined an alternative technique of extracting tungsten from wolframite ore using a fusion method with ammonium phosphate salt. Current techniques use alkali salts to decompose tungsten ores and use various purification methods to produce ammonium paratungstate, which is a key intermediate precursor in the extraction of tungsten. In this study, a two-step extraction process, which involves thermal decomposition of the ore using fusion and a separation stage, is examined. The novelty of this technique is the ability to completely decompose wolframite ore and form an unstable tungsten oxide phosphate (WO2(PO3)2) compound. The instability of WO2(PO3)2 in deionized water enables selective isolation of tungsten as insoluble precipitates of WO3 and WO2. The decomposition reaction of WO2(PO3)2 is influenced by the presence of oxygen and determined to be first order under ambient conditions. Scanning electron micrographs and X-ray diffraction analysis showed above 80% of the tungsten precipitated compared with the amount that remained in the filtrate solution.

Jul 10, 2024

By Page-Shipp. R. J., Elizabeth Harris

A study of the response of South African white gold miners to exposure to dust in their working environment yielded large quantities of dust data. Analysis of this data (presented in summarized form) reveals a variety of interesting relationships, including the shift-long exposure of different occupational groups, the dust levels due to various mining operations, relationships between different dust-measuring procedures and time trends in dust levels during the shift. The statistical probability of contracting silicosis at various levels of exposure to this dust is reported briefly. A new method of using microscope counts to estimate the respirable mass of dust samples is given in an appendix.

By J. L. Gaigher

A simple mineralogical regression model is described, which was devised in order to help the flotation plant cope with rapidly changing headgrades and feed mineralogy. Minerals in the feed were determined by means of quantitative X-ray diffraction and compared with plant performance parameters and flotation reagent consumption rates, using regression analysis. A mineralogical regression model for predicting recovery served to motivate flotation plant personnel and also set standards whereby flotation performance could be measured. The reagent consumption model indicated in which direction any or all of five flotation consumption rates should be altered. All practically measurable parameters, even those showing poor or no correlation, were included in the model, provision being made for the continuous update of a batch of data of 30 lines. Compared with the method of multiple linear regressions, the r2 is poorer at 0,41 (versus 0,50), but the mean standard error of estimate for both methods is identical at ± 6,6 units. The regression model is simpler than the method of multiple linear regressions, and although the accuracy of prediction is not high (41%), the mineralogical regression model proved to be successful in practice. Flotation efficiency, as measured by the mean ratio of head to tails grade, for the 9 month period after the mineralogical regression model was implemented on an hourly basis, improved from 2,8 to 3,2, which is equivalent to an improvement in average flotation recovery of 5% relative.

Jan 1, 1987

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By K. Wu, X. Yuan, R. Du, C. Chao

"Lump coals are currently employed to replace part of coke in the COREX melter-gasifier for ironmaking. In order to optimize the process, the pyrolysis kinetics of Datong coal used in the COREX process was studied. A sectioning method is proposed to overcome certain shortcomings of traditional methods for studying the pyrolysis of coal. Based on the sectioning method and the characteristics of the coal pyrolysis process, the temperature range was divided into three intervals. In the first, the adsorbed gas and water of crystallization were removed; in the second, the coal was transformed into semi-coke; and finally, the semi-coke was further coked. Three models of reaction were then established to study the different stages of the pyrolysis process: an interfacial chemical reaction model, a random pore model, and internal diffusion with shrinking volume. The results showed that the experimental data fitted the models well, with all correlation coefficients (r2) exceeding 0.97. Finally, the mechanisms of reaction and kinetic parameters for each temperature range were derived, which laid a necessary foundation for optimizing the usage of non-coking coal in the COREX process. IntroductionIn view of environmental concerns and the shortage of good-quality coking coal, the COREX process was designed as a new ironmaking technology, attracting wide attention (Fang et al., 2005). In this process, lump coal and a small quantity of coke are directly charged into the melter-gasifier, where a high-quality reducing gas is generated for the reduction of the iron ore (Kumar et al., 2009). In contrast to the conventional blast furnace (BF) process, non-coking lump coal is used as the reducing agent and as the energy source, and the iron charge consists of lump ore and/or pellets, which results in the elimination of the coke oven and sintering plant as well as a decrease in investment (Kumar et al., 2009; Liu et al., 2012).Although the COREX process has made great progress, in current production practice the energy consumption greatly exceeds that of the BF, and it requires a certain amount of coke to maintain permeability of the semi-coke bed (Wang et al., 2008). In addition, the process consumes a lot of good-quality lump ore and lump coal. The pyrolysis of coal is the first step in most coal conversion processes, such as carbonization, gasification, and combustion (Aboyade et al., 2013). The reaction behaviour of lump coals in the COREX melter-gasifier is crucial, as it determines energy utilization and gas composition, as well as the metallurgical properties and particle size of the semi-coke produced (Prachethan et al., 2011; Zhang et al., 2014). In order to optimize the process and improve its competitiveness, the pyrolysis kinetics of Datong coal used in Baosteel’s COREX C-3000 facility was studied."

Jan 1, 2016

The optimal design of production phases and ultimate pit limit for an open pit mining operation may be generated using conventional or stochastic approaches. Unlike the conventional approach, the stochastic framework accounts for expected variability and uncertainty in metal content by considering a set of equally probable realizations (models) of the orebody. This paper evaluates the performance of a new stochastic network flow approach for the development of optimal phase design and ultimate pit limit using a gold deposit as the case study. The stochastic and conventional frameworks as considered here utilize the maximum flow and Lerchs-Grossman (LG) algorithms, respectively. The LG algorithm is restricted to considering an estimated (average-type) orebody model, while the stochastic maximum flow algorithm is developed to simultaneously use a set of simulated orebody realizations as an input. The case study demonstrates that, when compared to the conventional LG algorithm as used in the industry, the stochastic approach generates a 30 per cent increase in discounted cash flow, a21 per cent larger ultimate pit limit, and about 7 per cent more metal, while it maintains a consistency in phase size.

Jan 1, 2012

By J. P. M. Hojem, C. Dimitriou, N. C. Joughin

This paper describes the design and construction of the first experimental underground rockcutting machine from measurements of cutting forces determined in tests on small rock specimens in the workshop. The deficiencies of this design, revealed by stoping with almost identical rockcutting machines, are described. An account is given of the design and construction of further experimental machines incorporating substantial improvements which made them technically feasible for use in production.

By M. David

This paper addresses the problem of technological transfer in geostatistics. Expert systems have become popular in certain fields because the needs of the industry are not provided for by traditional concepts and systems of education. The explicit knowledge approach in developing expert systems is presented through two experiments. The first describes a dedicated system written in GOLDEN LISP and the second a shell, using INSIGHT2, which has more general applications. Using expert systems forces on the user a new approach to parameter definition, and as an example an original method for the research of any anisotropy axes is developed which might well be useful in traditional programming. Two examples of application to a coal and a gold deposit are given.

Jan 1, 1987

By F. M. Russell

Scheduling the extraction and rates of production for an underground mining operation is a common task carried out during the life of a mine, from the initial feasibility study through to the final production phase. The scheduling process can be complex when several requirements have to be satisfied, for example, match mill capacity and maximize net present value while constrained by mining sequence and availability of resources. Many mines have computer programs relevant to their operation but because they are site-specific they need considerable reprogramming to be adapted to other operations. Other methods currently in use also suffer drawbacks: manual spreadsheets are laborious, computerized spreadsheets cannot handle sufficient constraints, and operations research techniques require a complex mathematical model to be set up. The use of network analysis techniques has been proposed previously but the unavailability, until recently, of easily used computer programs has not allowed this approach to be developed. There are now many programs which can be used; however, the particular program which has been adapted to mine scheduling is Metier's 'Artemis-PC' running on IBM-XT or compatible machine. The use of network analysis offers many advantages, including the use of a logical mining sequence; activities can be as detailed as required; related activities can be readily incorporated, and costs can be easily extracted. A heuristic approach is necessary to optimize the schedule, but the ease and speed of program execution enables this to be readily achieved, while leaving the mining engineer in full control. The paper discusses the problems encountered in mine scheduling and current solutions. It then details the use of network analysis techniques and the application of the Artemis-PC program to solve mine scheduling problems.

Jan 1, 1987

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, there by lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3Dmulti-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2006

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009