Search Documents

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By A. Smith

The practice of leaving barrier pillars between adjacent longwall panels at The Durban Navigation Collieries (Pty) Ltd (Dumacol) has resulted in a considerable loss of coal reserves. Dumacol has now modified the layout of its longwall panels to allow the concurrent mining of barri9f pillars and the extraction of the longwalls. The Implementation of the new panel layout has increased the percentage extraction of reserves and will result in an extension in the life of the mine. The method of extracting barrier pillars between adjacent longwall panels is described in this paper.

Jan 1, 1985

By D. J. Shields

The U.S. Bureau of Mines has developed a microcomputer-based mineral modelling system that enhances analytical capabilities of the agency. It draws upon the extensive data base previously developed for the Bureau's Availability studies. The model is first formulated as a generalized network flow optimization problem, the optimal flows from which are fed into a transportation algorithm. The goal of the modelling system is first to fulfill prespecified demand at the minimum opportunity cost and second to identify feasible, optimal trade patterns. The system facilitates the analysis of policy issues on a real-time basis and supports the Bureau's mission to assess mineral resources.

Jan 1, 1987

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

Dr H. J. van Eck (Honorary Life Member): "Mr President, I regard it as a signal honour that I was invited to address the South African Institute of Mining and Metallurgy on its 75th Anniversary. I also wish to add my congratulations and good wishes to the many you have already received on this memorable occasion. Seventy-five years is indeed a good age and the achievements of your Institute certainly justify this special celebration. South Africa owes her present prosperity largely to the technological ability and determination of her own people. Members of the Institute contributed in large measure to this great development of our country and through the years have upheld their high reputation for scientific integrity, dynamic enterprise and dedicated service. It was their knowledge which provided the key to unlocking the mineral wealth which lay dormant for countless ages. The history of world mining dates back many centuries. We know of the mercury mines of Spain, the tin mines of Cornwall and the zinc mines of Poland, but it was not until colonization of the western hemisphere started in about 1500 that mining of any consequence began in North America. It is true that the peoples of South America and Mexico had accumulated wealth out of gold and silver, but industrialized mining was not a feature of these agrarian cultures. The mining wealth that eventually developed in North America was based on advances in the technology of processing minerals and served as an incentive to people in other new countries. Big mines were opened elsewhere in the world. From Canada, Mexico, Venezuela, Brazil, Peru, Chile, Bolivia, Rhodesia, Australia, Burma and India, to name but a few, there has been a steadily increasing production of an expanding range of minerals and metals. By the middle of the 20th century the trend was to increase the production and use of such comparatively uncommon metals as cobalt, nickel, titanium, and others, and a great mining rush started to search for, and develop, the deposits of uranium, and related radio-active minerals. It is worth pausing a few minutes to reflect that most of early mining was based on the recovery of virgin metals like gold and silver or easily treated high grade ores of copper, tin and zinc. Today, much of this type of mining would be regarded as picking the eyes out of the mine. With the development of improved ore separating, ore concentration and recovery processes, we developed into bulk mining and bulk treatment and in South Africa we have some very big mines, also outside the gold mining industry at Phalaborwa, for instance. Mining techniques are applied which compare with the best in the world. These large mines could only develop because of the perfection of new concentrating techniques and, of course, because of the development of markets. We have mentioned nickel and cobalt. These names were given to those mischievous mining sprites called nickels and kobolds to whom the suspicious miners ascribed their inability to smelt copper from copper nickel or arsenious copper ores. In South Africa, the presence of minerals was known to the modern Western world as far back as 1497 when Vasco da Gama found the native 'strandlopers' at the St. Helena Bay wearing copper rings. In 1669, after the British East India Company had formed their settlement, they employed miners and assayers in prospecting for minerals and in 1685 found traces of copper in the copper mountain of Namaqualand where some 170 years later a rich deposit of copper was to be opened up. This deposit also had a chequered

This International Mine-Surveying Conference will take place in Budapest (Hungary) from 5 to 14 June, 1972. Detailed information can be obtained from the Mine-Surveying Working Committee of the Hungarian Mining and Metallurgical Society. Write: OMBKE Bányaméröi Munkabizottsag Budapest, V., Szabadsag ter 17, Hungary. SYMPOSIUM ON NICKEL The 'Gesellschaft Deutscher Metallhiitten-und Berglaute' is holding a Symposium on nickel on 24-25 September, 1970 at Wiesbaden, on the occasion of the G.D.M.B. Annual Meeting. Some 24 papers will be presented by metallurgists from many important companies around the world. Information may be obtained from The Secretary, G.D.M.B., Postfach 210, 03392 Clausthal-Zellerfeld, German Federal Republic. VISIT TO THE COUNCIL FOR SCIENTIFIC AND INDUSTRIAL RESEARCH On 23rd June, 1970, members of the Institute visited the C.S.I.R. in Pretoria. More members had booked for this tour but the current flu epidemic caused cancellations which was unfortunate. The visit was organised with military precision, which prevented detailed discussion of any particular subject, but provided a bird's eye view of a large number of interesting projects. The visit was packed with interest for all and those requiring further information were invited to contact the relevant divisions afterwards. Or Denkhaus welcomed the delegates and stressed the importance of integrating research efforts with industry's requirements. An excellent colour and sound film was shown which depicted the work of the Rock Mechanics division. This showed very clearly methods used for preparing rock samples and demonstrated the machines and instruments for the various tests. It made one realise the extent to which this research has been integrated with the actual mining situation. The fullscale experiments underground showed the failure of pillars under applied loads and were very interesting. This is undoubtedly a film which all mining people should see. After the film the rock mechanics laboratories were visited where the actual machines were seen and described. We then visited the metal and strength mechanics sections where the metallurgists were able to see some interesting experiments and tests. We also visited the Aeronautics Research group where a large 1 000 hp wind tunnel was inspected. We were told enough about this to realise something of the complexities involved in the design and operation of a closed circuit tunnel of this type. The tunnel is used for tests on models which are necessary for the design and modification of aircraft. After a very excellent lunch at the C.S.I.R. recreation centre, the delegates attended two lectures-one by Mr. Mandersloot of the Chemical Engineering group, who outlined the varied functions of this group and told us something of their work. Of particular interest was the research into the suitability of various South African manganese ores for dry cell batteries. Work on the thickener settlement studies interested the metallurgists. The second lecture was given by Mr Donaldson of the National Building Research Institute. This Institute has about ten divisions each of which covers a particular aspect of building research. The work of the soil mechanics division was described in detail and illustrated by coloured slides. This was particularly interesting and demonstrated clearly how building failures result from lack of attention to detail of construction where unstable soil conditions exist. Cracks in walls of compound blocks brought the subject home forcibly to the mining delegates. This division has also caried out important work on sinkholes and sUmes dams and produced some positive results. Altogether the visit was most interesting and enjoyable. It was made more worthwhile because the emphasis was on the work being carried out and not on just seeing the laboratories. The Institute is greatly indebted to the C.S.I.R. and its staff for the very excellent arrangements made.

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By D. Brazier, W. Laing, D. Nixon

Keywords: Pyrometallurgy, furnace, smelter, copper, Palabora The Palabora copper smelter has operated for the past 38 years, treating concentrates produced at the mine site. Palabora has reduced captive material by almost 40 per cent with the transition from a large open-cast to a smaller underground mine. The smelter and refinery complex was designed to treat 120 kt contained copper units per annum, with the underground only supplying 70 per cent of the feed. The agreed strategy was to import enough concentrates to maximise production and reduce operational unit costs. This transition has presented the Palabora management with new challenges both in technical and financial aspects.

Jan 1, 2006

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003

By L. J. Park, A. D. Thomas

Gladstone Pacific Nickel Limited (GPNL) is proposing to develop the Marlborough nickel deposit in central Queensland and the Yarwun Refinery in Gladstone, Australia. The project proposes to connect the two sites with a DN 500, single pump station slurry pipeline, transporting up to 4 Mtpa of nickel laterite ore as slurry 180 km from Marlborough to Gladstone. Slurry viscosity is a key parameter influencing pipeline design. Not only is the slurry viscosity relatively high, requiring pumping at low concentrations, around 30% by weight, but the viscosity (yield stress and plastic viscosity) increases with shearing or agitation. It is argued that the viscosity changes can be analysed in terms of total energy input, including energy input during grinding. The slurry viscosity is therefore expected to increase along the pipeline and the pumping concentration must be low enough such that the increase in yield stress does not cause transition to laminar flow towards the end of the pipeline. The base viscosity of two ore types is determined using a rotational viscometer for minus 212 micron slurries. Viscosity variations with ore particle sizes of d99 212, 425 and 600microns are investigated. For each of these particle sizes the expected increase in viscosity during pipeline transport is simulated on a laboratory scale by agitation with a turbine mixer in a baffled container to give the same equivalent unit energy input as will occur in the pipeline. Tests were also conducted on the d99425 micron slurry in a 2.7 metre diameter DN 200Wheelstand, rotated for the 23 hour transit time and at a similar relative velocity as in the pipeline. Based on the Wheel stand test results the yield stress is expected to increase by a factor of 3.1during pipeline transit. The preliminary design allows for a reduced pumping concentration to accommodate this increase in yield stress towards the end of the pipeline.

Jan 1, 2007

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

COUNCIL The following served on Council during the year under review Office Bearers Dr J. P. Hugo (President), P. W. J. van Rensburg and Professor R. P. Plewman (Vice-Presidents), Professor D. D. Howat (Immediate Past-President), and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council H. P. Carlisle (until February), R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, J. B. Mudd, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen (co-opted May 1973), and P. A. von Wielligh. Branch Chairmen A. Bain (Witbank-Middelburg Branch), C. J. Isaac (O.F.S. Branch). Past Presidents Serving on Council R. J. Adamson, M. Barcza, H. Britten, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Professor J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid, and V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 18, and the standing committees held 29 meetings. MEMBERSHIP Twelve Fellows, ten Members, twenty-one Graduates, eleven Associates, thirty-one Students, and forty-two Company Affiliates were elected during the year. One Member was reinstated. Eight Fellows, two Members, and two Associates were admitted to retired membership. Four Graduates were transferred to Members, one Associate to Member, three Students to Members, one Graduate to Associate, two Students to Graduates, and one Student to Associate. Your Council records with deep regret the death during the year of the following : D. R. Campbell, J. Daniel, M. J. Dennehy, and F. S. C. Rogers (Life Fellows) ; W. T. balling and T. Pryor (Life Members); C. Boocock, W. Drake R. J. Moore, M. P. Pearse, J. M Pike, W. A. Schwezoff, A. I. Suss man, and L. G. S. Wright (Fellows) ; A. F. Chalmers (Member) ; and W. R. Gerry and G. T. Rimmer(Associates). A comparative statement of membership as at 30th June, 1973, and the end of the previous year it shown in the following tabulation: 30th - 30th June, - June, 1972 - 1973 Honorary Life Fellows 5 - 4 Honorary Fellows 13 - 9 Life Fellows 181 - 177 Fellows 541 - 536 Members 479 - 487 Graduates 115 - 128 Associates 182 - 186 Students 162 - 183 Company Affiliates 24 - 64 1 702 - 1 774 JOURNAL The papers that were published in the Journal during the year are listed below: August, 1972 The effects of chromium oxide, iron oxide, and calcium oxide on the liquidus temperatures, viscosities, and electrical conductivities of slags in the system MgO-Al2O3-SiO2, by M. S. Rennie, D. D. Howat, and P. R. Jochens A study of the dust exposure of South African white gold miners, by R. J. Page-Shipp and Elizabeth Harris A forecast of the coal and uranium requirements for electric power generation in South Africa, by E. J. Maunders September, 1972 Mine management by objectives, by A. A. Hazell Some aspects of the deformation behaviour and temperature rise during instantaneous compression loading of high purity aluminium, by H. J. E. Hamel Computer control of flotation at the Ecstall concentrator, by M. P. Amsden, C. Chapman, and M. G. Reading Optimizing the public gains from the exploitation of mineral resources, by A. Azis and J. Zwartendyk October, 1972 Presidential Address: Nuclear energy: its interactions with mining and metallurgy, by J. P. Hugo Presidentsrede: Kernenergie: sy wissel-werkinge met mynbou en metallurgic, deur J. P. Hugo Raise-boring experiences in the gold mines of the Anglo American Corporation Group, by J. W. Wilson and P. C. Graham November, 1972 Materials for winding plant components, by G. T. van Rooyen An analytical solution to the batch-comminution equation, by R. P. King A new approach to the study of human factors in stope productivity, by A. C. Lawrence Fundamental studies of the flotation process: the work of the National Institute for Metallurgy, by N. P. Finkelstein and V. M. Lovell Growing use of deionised water in surface coating techniques, by W. F. Lorch December, 1972 The development and application of a computer system to aid in the planning of production in mines, by F. H. Deist, L. F. Duvel, J. D. Austin, and H. D. Small PERT, and how PERT techniques can be used in modern mine management, by E. J. Boome and A. C. Schmidt A critical comparison of specific cooling power and the wet kata thermometer in hot mining environments, by J. de V. Lambrechts January, 1973 Liquidus temperatures in the Cr-Fe-Si system in the composition range representative of ferrochromium-silicide produced in South Africa, by J. C. M. Wethmar, D. D. Howat, P. R. Jochens, and O. A. W. Strydom Platinoids in the Witwatersrand System, by C. A. Cousins The development of a continuous recording scintillation counter mounted on a cyclometer, by P. D. Teens and D. Visser February, 1973 Computer analysis, modelling, and optimisation of gold recovery plants of the Anglo American Group, by M. I. Brittan and E. J. J. van Vuuren The significance of the mineralogical and surface characteristics of gold grains in the recovery process, by C. E. Feather and G. M. Keen Statistical valuation of diamondiferous deposits, by H. S. Sichel March, 1973 The effect of the reactivity of lime on desulphurisation efficiency in the basic oxygen furnace, by A. A. Hejja, D. D. Howat, and P. R. Jochens A review of real-time particle size analysers, by A. L. Hinde In situ measurements of the surface heat transfer coefficient in underground airways, by K. R. Vest April, 1973 An investigation into the kinetics and mechanisms of the oxidation of iron (II) by oxygen in aqueous chloride solutions, by R. P. Colborn and M. J. Nicol Electric smelting at Rustenburg Platinum Mines Limited of nickel-copper concentrates containing platinum-group metals, by J. C. Mostert and P. N. Roberts Metallurgical considerations in the

Jan 10, 1973

By J. Portal

One of the key products produced by the mineral sands industry is the titanium dioxide slag, a process that requires grinding of a coarse product down to a valuable saleable product. Traditional methods have included the vertical roller mill in tandem with dynamic air classifiers and, alternatively, two-stage grinding and crushing through an AG mill in closed circuit with a dynamic classifier and secondary gyradisc crushers. The products produced, commonly known as chloride and sulphate slag, are differentiated by the particle size distribution of the final product. The more valuable chloride slag must, by specification, be a product sized in the range between 850 and 100 microns?the more fines generated in the grinding process, the less higher valuable final chloride slag is produced. This paper will explore a technology that is new to both the mineral sands and to other mineral processing industries. Inter particle communition, or IPC as it is known, has been applied in the cement industry to improve the performance of clinker grinding mills. The principle is to create a process of material on material comminution under high pressure that fractures the material along the grain boundaries rather than breaking it smaller than a gap setting in the crusher. The process is now looked at for the TiO2slag producers because of the potential benefits of energy savings and with a minimal generation of minus 100-micron fines. Discussions will revolve around the design and functionality of the Rhodax® both from a process and maintenance perspective, a typical test regime and results on slag grinding. The development of the flowsheet necessary for the process will be examined, the ancillary equipment required and finally the scale-up from the test to an industrial plant will be investigated. Full-scale results of an operating plant will also be given showing the benefits that can be realized. A promising new flowsheet with fines reintroduction to the Rhodax® crusher will be presented.

Jan 1, 2007

By J. P. Gouvea, W. Geel

Resin bolting in South Africa has been developed and refined in underground coal mines (i.e., soft rock) since the late 1940s. The extension of resin bolting to hard rock mines started in 2003 and has required significant adaptations, challenging the status quo from both a supplier and applicator perspective. As far as resin bolting is concerned, the most affected aspect in coal mining and hard rock mining environments, is the rock drills or machinery used for installation. Hard rock mines mostly use hand-held airlegs with limited thrust, low torque, and rotation speed, relative to coal mine mechanised bolters. Resin bolt development for hard rock mines was, and still is today, predominantly focussed on compensating for the ‘shortfalls’ of using hand-held airlegs. At face value, hydro-powered rock drills, which are more powerful than traditional handheld equipment, provided hard rock mines with a means to attain more consistent and reliable resin bolt installations. This paper assesses the quality and performance of hydro-powered resin bolting at an intermediate to deep level platinum mine in South Africa and its potential contribution to rock-related instabilities when applied erroneously. The findings of this paper necessitate a revision of current quality control and quality assurance measures related to resin bolting for underground support.

Nov 24, 2025

Past work on the ignition of methane-air mixtures by coal-cutting picks is reviewed, with special reference to the factors that contribute to ignitions and ways of reducing them. The main conclusions obtained from this review are outlined for the following aspects: mechanisms of ignition, methane concentrations, and the roles of rock types, cutting parameters, cutting tools, and water. However, many of these factors have been investigated on a qualitative, rather than on a quantitative, basis. A considerable amount of effort over a long period has been expended in this area of research. It is shown that a number of the factors influencing ignitions by machine picks have been researched adequately, but that there is still work to be done. Research is continuing in this area, being concentrated primarily upon the ignition potential of the coal-cutting pick.

Jan 1, 1985