Search Documents

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014

By D. Van Dyk

Horizontal rotating mills are being used all over the world in different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions that are not always fully understood. Failures are therefore experienced, over time in the industry, which cannot always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyse these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyse the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating and the effect on the fatigue life of the mill gearing components, conditions are better understood, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2006

By M. Bester, R. Carey, T. Russell, J. van Heerden

"In order to reach the goal of optimal and safe extraction of the mineral reserve, the mining industry is increasingly focusing on reconciliation across the mining value chain to ensure that the mining process occurs in a progressively more predictable manner. This will consequently improve the understanding of mine plans and their associated implementation risks, ultimately leading to increased investor confidence. In terms of geotechnical engineering, mine to design performance assessment is a critical aspect of mine to plan adherence focusing on the complex aspects influencing slope performance. A mine to design reconciliation process therefore needs to systematically track implementation and geotechnical aspects in order to review or update slope design criteria and pit layouts according to the mine planning cycle as the mine is developed. This paper describes the development and implementation of a standardized mine to design reconciliation system for operations utilizing laser scanning technology, analysis tools, as well as associated key performance indicators. Performance is evaluated on final pit boundaries in terms of geometry achieved as well as blast performance evaluation of face conditions. These aspects as well as the resulting catch berm capacity should be captured in an information system, enabling longer term trend analysis and detailed root cause analysis where unsatisfactory outcomes occur. Adverse outcomes should subsequently be incorporated into the mine’s risk management process informing risk mitigation measures including blast design adjustments, slope design changes, or rockfall protection measures. IntroductionIn order to reach the goal of optimal and safe extraction of the mineral reserve, the mining industry is increasingly focusing on reconciliation across the mining value chain to ensure that the mining process occurs in a progressively more predictable manner. This will consequently improve the understanding of mine plans and their associated implementation risks, ultimately leading to increased investor confidence. In terms of geotechnical engineering, mine to design performance assessment is a critical aspect of mine to plan adherence focusing on the complex aspects influencing slope performance. A mine to design reconciliation process therefore needs to systematically track implementation and geotechnical aspects in order to review or update slope design criteria and pit layouts according to the mine planning cycle as the mine is developed."

Jan 1, 2016

Commissioning of the Cannington processing plant began in October 1997. The nameplate capacity (of 1.55 million tonnes of ore per annum) was achieved relatively quickly. Since then (like many mines) the operation has strived to increase throughput and improve valuable metal recoveries, to offset declining head grades and lift the value of the operation. The processing plant now has the capability of treating over 3.2 million tonnes of ore per annum and in financial year 2005/06 the combined concentrate production exceeded 600 000 wet tonnes, approximately 80 per cent above concentrate output in the first full year of operation (at the design feed rate). This improved performance was achieved by making changes and additions to each of the major unit processes - primary grinding, flotation, leaching, filtering and paste fill preparation. The changes have included: adding a fines flotation circuit, expanding the grinding circuit, adding a pebble crusher, switching from continuous to batch leaching, building paste conveyors and decommissioning the column flotation cleaning circuits. This paper reviews these changes, outlines the current operating practices and discusses the challenges or opportunities that remain.

Jan 1, 2007

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By J. Bullón, A. Pérez

Some years ago, Ferroatlantica developed a new type of electrode known as the ELSA electrode. In this electrode there is a central graphite core that provides support, surrounded by an annulus of Søderberg paste that gets baked during operation. This technology has been implemented on several silicon furnaces around the world, and was reported on during the previous Infacon conference. In all electrodes, but particularly in the ELSA electrode, the quality and consistency of the paste are important for correct operation. As the type of paste varies between customers and between countries, Ferroatlantica has developed a quality control procedure for their customers of this technology. This procedure is geared to the point of view of the customer rather than the paste producer. The analysis is based on the desired flow pattern of the raw paste and on the desired mechanical and electrical properties of the baked paste, as experience has shown that these are the most important parameters to monitor in order to avoid having problems with the resulting electrodes. This paper discusses these methods of paste analysis in the light of complementary studies that have been done when there has been an electrode breakage in the different plants.

Jan 1, 2007

By K. A. G. Blendulf

The paper describes tests on horizontal-belt filters for the filtration of gold and uranium. The promising results led to the installation of 17 such filters (ten of them 120 m2 in size) in the mine&apos;s metallurgical plants, and their operation is discussed. Although several problems were encountered both in operation and maintenance, it is concluded that, with correct operation and suitable filter cloths, exceptionally good metallurgical recoveries can be achieved at filtration rates twice to three times higher than those on rotary filters.

Jan 1, 1997

By J. P. Hoffman

This paper describes the metallurgical aspects and properties of a duplex austenitic-ferritic steel SAF 2205. As well as having high yield strength and hardness, SAF 2205 combines the high resistance of ferritic stainless steels to chloride-induced stress-corrosion cracking and the excellent resistance of austenitic stainless steels to hydrogen-induced stress-corrosion cracking. Its alloying elements contribute to its mechanical and corrosion properties as follows: nitrogen increases its pitting potential and improves its strength, nickel increases its resistance to pitting and its toughness, chromium and molybdenum give improved resistance to pitting and crevice corrosion. SAF 2205 has better resistance than steel types 316 Land 317 L both to pitting corrosion and to stress-corrosion. This makes it a very good material for pipes, tanks, and pumps in harsh environments such as those in petrochemical and desalination plants.

Jan 1, 1986

By A. Smith

After the introduction of mechanized bord-and-pillar development at Dumacol in 1958, pillars were being developed at a much faster rate than they could be extracted by hand loading methods. Efforts were therefore made to increase the rate of pillar extraction by mechanization. Following two partially successful mechanized stooping trials in 1964 and 1971, it was decided that mechanized pillar extraction with 1 m3 cable-reel front-end loaders should be introduced. The first section to employ the new equipment started production in May 1979, and the mine now has four mechanized pillarextraction sections in operation. Considerable improvements in production, productivity, safety, and percentage extraction have been achieved.

Jan 1, 1985

By S. Selmer-Olsen

New trends and developments in the production of ferro-silicon, ferro-manganese and ferro-chrome alloys are discussed, with emphasis on the general trend to the adoption of large production units. Problems which arise, both of a metallurgical and an electrical nature, due to the use of large electric furnaces, are outlined with specific reference to the limitations imposed by the power carrying capacity of Soderberg electrodes, the furnace resistance and the furnace reactance. The implications of combining high resistance within the furnace with good metallurgical operating conditions are illustrated by considering the production of ferro-silicon and ferro-manganese. The possibility of replacing electric furnaces used for ferro-manganese production, by large low shaft blast furnaces using oxygen enriched blast, is mentioned. The continued use of small electric arc furnaces for ferro-chrome production is also mentioned, and is ascribed to lack of ore suitable for treatment in large furnaces. Agglomeration of chromite ores appears to be a possible answer to this problem.

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By P. R. Janisch

This paper reviews the sources, production, and technology of gold in South Africa. First of al it details the geographical distribution of gold-bearing materials, together with the mineralogy and distribution of gold within those materials. It goes on to the geological origins, and to the discovery and early exploitation, of the gold deposits. The laws relating to the mining and disposal of the metal are explained, after which an outline is given of gold exploration, processing, and refining. The economics of gold production are discussed briefly, and it is concluded that, although present expertise in the financial and technological aspects of a gold-mining venture have largely reduced the risks involved, one severe risk remains: that the rate of cost inflation will not be matched by the rate of escalation in the gold price.

Jan 1, 1986

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By S. Subramanian, L. Mweene

A siliceous low-grade copper ore from Mpanda Mineral Field (MMF), located in south west Tanzania consisting of SiO2 (58.3%), Fe (10.4 %) and Cu (0.9 %) was initially subjected to selective dispersion-flocculation using sodium trisilicate (STS) as a dispersant and xanthan gum (XG) as a flocculant. Subsequently, the selectively flocculated fraction was floated using a collector combination of potassium ethyl and amyl xanthate (1:1) in the presence of poly-ethylene oxide (PEO) as a silica depressant, to get a copper concentrate. The mineralogical investigations confirmed that the MMF ore was mainly composed of quartz, chalcopyrite and pyrite. Adsorption studies indicated that the adsorption density of XG on MMF ore decreased with an increase in pH, while that of PEO was independent of pH. The adsorption isotherms of XG and PEO on MMF ore exhibited Langmuirian behaviour. The zeta potential studies of MMF ore indicated that the iso-electric point (IEP) was located at pH 2.6, presumably due to its high silica content. In the combined presence of XG and STS, the zeta potential of MMF ore became more negative, with an increase in the concentration of STS. However, in the presence of PEO, the zeta potential of MMF ore became less negative with an increase in the concentration of PEO beyond the IEP, without shifting the IEP. Selective dispersion-flocculation of MMF ore improved the flocculated chalcopyrite grade to 19.8 %, yielding a degree of flocculation and a maximum separation efficiency of 12.1 % and 85.7 % respectively, after three desliming stages in the presence of 30 ppm of STS and 30 ppm of XG. A copper concentrate of 29 % grade and 90 % recovery containing silica of 0.9 % grade and 1.7 % recovery was achieved by flotation of the selectively flocculated component, using PEO as a depressant for quartz. Keywords: Flotation kinetics, flotation machines, flotation bubbles, particle size

Jan 1, 2020

By A. McCracken

Probabilistic methods for assessing the reliability of engineering systems in mining are the way of the future. So agreed the delegates of a recent short course on the subject, entitled &apos;Reliability-based Approach in Mining engineering Design&apos;. This was a very successful five-day technical course sponsored by The South African Institute of Mining and Metallurgy and held at Mintek from 7th to 11th March, 1988. The main lecturer for the course was Milton E. Har, Professor of Geotechnical Engineering at the School for Civil Engineering of Purdue University, Indiana, USA. Professor Har was ably assisted by Dr Dirk van Zyl, a former student. Science quiz Teams of pupils from 37 schools within a radius of 12 kilometres of the Council for Mineral Technology (Mintek) competed in a science quiz held by Mintek at its headquarters in Randburg on Tuesday, June 7th, 1988.

Jan 1, 1988

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By N. C. Joughin, H. Wagner

Research is a business activity, and is as different from other business activities as banking is from mining. attempting to use research to solve their problems, managers do not always recognize its unique features, are frequently disillusioned with the outcome. With a view to enabling managers to use research more effectively, an outline is given of the features of research as applied to mining. Types of research are distinguished, and stages in the research-and-development process are identified. The time-scales and resource requirements of the various types and phases of research are explained. Examples of research that have reached implementation in gold mining are given to illustrate the features mentioned. Practical and economic considerations are discussed, and pitfals and recommendations in the use of research are highlighted.

Jan 1, 1989

By S. Curry

The Objana Cement Plant is located in central Nigeria, approximately 200km south of capital city Abuja (figure 1). It is the second largest cement plant in Africa, and the fifth largest in the world [1]. The selected mining location is unique as it has all the major raw materials (except gypsum) in close proximity. This includes limestone, clay, marl, laterite soil, and laterite iron. [ ] The plant has a capacity of 5 million metric tones per year (~15,000 tones per day). A 135 megawatt gas-fired power plant, with 90 km of natural gas pipeline, was constructed to power the plant. The total project cost is approximately 1.2 billion US dollars. The lifeline of the plant is two overland conveys totalling 7.7km in length. The first 800m conveyor is relatively mundane. The second conveyor however, is unlike any other troughed belt conveyor in the world. It 6.9km length transports 2,400 T/H and operates at 5.0 m/s. Its ?snake? profile consists of 11 vertical cuvees, and four horizontal curves. The last of which is 2,000m in radius, has a length of 2.2km, and is located at the high tension head end of the conveyor. Although these specifications are noteworthy, the unique feature of this system is that it is entirely elevated from head to tail using a triangulated truss gantry structure (figure 2).

Jan 1, 2008