Search Documents

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By J. A. L. Napier, J. S. Kuijpers

SYNOPSIS This paper demonstrates that the horizontal stresses induced by the creation of a tabular scope in a single mining step are always tensile at the centre of the stope span, but that compressive stresses are actively generated in hangingwalls and footwalls during sequential mining. A stress-distribution mechanism is introduced, and is used to explain the results for elastic behaviour, and for inelastic behaviour both during a single mining step and during multiple mining steps.

Jan 1, 1991

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

By J. Palarski

Long waling is used in most Polish coal seams, with backfilling to support the roof, to create an artificial hanging wall to prevent movement if the rockmass, and to eliminate the fire hazard in abandoned mine workings. This paper discusses the results if tests conducted on 7 different backfill mixtures, and gives equations for the estimation if the flow if backfill slurries through gravitational pipelines.

Jan 1, 1994

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By T. G. Maepa

"The creation of mine excavations alters the stress distribution in the surrounding rock mass. In modern mining, resin-grouted rockbolts are used as a means of support in order to redistribute stresses and reestablish equilibrium in the rock mass. The success of resin-grouted rockbolting depends on the design of the system and the correct installation of the support units.The support design and rockbolt installation procedure at a platinum mine in the Bushveld Complex were investigated. A number of issues that resulted in poor installation were identified, including resin admixture, incorrect length and orientation of support holes, over- or under-spinning of the resin, and incorrect rockbolt tensioning. The support design used at the mine was reviewed and its limitations identified. A number of recommendations were made for optimizing the support design by reducing the diameter of the drill bit and reducing the length of the support holes. These changes will enable the mine to use different combinations of resin capsules. Implementation of the proposed changes will lead to a significant reduction in the cost of installation per support hole, as well as improve productivity and safety.IntroductionThe creation of any mine excavation disturbs the virgin state of stress in the Earth’s crust. This results in stress concentrations that interfere with the stability of the rock mass surrounding the excavation. It is essential to modify the internal behaviour of the rock mass surrounding excavations in order to reinforce the ground and stabilize excavations. Resin-grouted rockbolts are extensively used for this purpose. Esterhuizen (2014) stated that when effectively installed, the rockbolt exerts a clamping force and a bonding strength that keeps the rock mass together. This increases the cohesive strength of all discontinuities in the rock mass and enhances the stability of the excavation. Poorly designed and installed ground support is ineffective and constitutes a safety hazard. It is therefore crucial for every mine to ensure that any form of ground support is designed and installed correctly. This research evaluates the installation of resign-grouted rockbolts and identifies challenges and solutions for improved safety as observed at an operating hard rock mine. The support design used at the mine was reviewed and the design parameters optimized. The outcomes will enhance the efficiency of support and minimize the costs associated with the installation of resingrouted rockbolts."

Jan 1, 2017

The finite element method of stress analysis is nowadays widely used in the fields of mining, mechanical and civil engineering. This paper presents a short description of the three-dimensional method, in which the elements used are arbitrary hexahedrons. Two examples of the application of the method are presented, namely, calculation of the elastic stress distributions in a coal pillar and in an opencast mine.

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By M. J. Southwood

SYNOPSIS Experiments carried out under atmospheric pressure and temperature (25°C) and sterile conditions show that the dissolution rate of nickel and copper from a pyrrhotite-pentlandite-chalcopyrite ore in a lixiviant of sulphuric acid is greatly enhanced in the presence of pyrite. At a pH value of 1,8 and in the presence of pyrite of equal mass to that of the ore, the recoveries of nickel and copper improved dramatically (21 and 80 per cent respectively). At a pH value of 4,0 the recovery of nickel was enhanced, but the chalcopyrite was refractory. A galvanic mechanism is probable, but cannot be proved from these experiments. The economic implications of the results are discussed.

Jan 1, 1985

By V. P. Kolosyuk, A. M. Bryukhanov

Occurrences of hazardous events (explosions of methane or coal dust, fires, outbursts) have been investigated and presented as a flow of events in time. It has been shown that flows of hazardous events in a long time span are homogeneous, stationary and no-after effect flows and can be considered as stationary Poisson flows. A flow of CH4/coal dust explosions that had happened for the last 27 years in Ukraine was analyzed. The explosions have been statistically processed. Practicability of agreement of statistical and theoretical data on mathematical expectation and mean square deviation of time interval between explosion and the explosion intensity has been stated. Probability of an emergency event in time is expressed through an exponential function, while mathematical expectation of an accident and mean square deviation of time interval between successive explosions are in inverse proportion to the accident intensity. Accident probability for practical purposes can be determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By J. Sjöberg, P. Lundman, E. Nordlund, C. Quinteiro

Abstract In the Kiirunavaara underground mine, crude ore is transported through ore passes from the production levels to the main haulage level. Failure and stability problems have occurred in some of these ore passes, with increasing frequency as mining depths increase. In this paper, selected results are presented from a research project run by LKAB. The presentation focuses specifically on stability analysis. Numerical models were used to identify failure mechanisms, in conjunction with empirical data and engineering judgment. The most important controlling factors governing failure and damage in ore passes were quantified. A causative model was established in which failure mechanisms and failure development were described. This model was used to formulate a prognosis of future ore pass stability, and for recommending remedial measures. Résumé Le transport du minerai entre les niveaux de production et le niveau principal de transport, à la mine de fer de Kiruna, se fait par des passes à minerai. Avec la profondeur d&apos;extraction grandissante, les problèmes de stabilité au niveau de ces passes à minerai se sont multipliés. Les résultats d&apos;un programme de recherche sur la stabilité des passes à minerai à la mine de fer de Kiruna sont présentés dans cet article. Les mécanismes de rupture ont été identifiés à l&apos;aide de modèles numériques, de données de terrain et du jugement empirique des ingénieurs. Les facteurs principaux controllant l&apos;instabilité des passes à minerai ont aussi été quantifiés. Un modèle a été établi dans lequel les mécanismes de rupture et le développement des dommages ont été décrits. Ce modèle a été utilisé à fins prédictives et remédiatives. Zusammenfassung In der Grube Kiirunavaara wird das gewonnene Erz über Sturzschächte von den Abbauebenen zu der Hauptförderebene gefördert. Mit zunehmender Tiefe des Abbaus sind vermehrt Standsicherheitsprobleme in den Sturzschächten aufgetreten, die teilweise zu Verbrüchen geführt haben. In dem vorliegenden Beitrag werden ausgewählte Ergebnisse einer Forschungsarbeit des LKAB präsentiert. Dabei wird der Schwerpunkt auf die Standsicherheitsuntersuchungen gelegt. Zur Ermittlung der Bruchmechanismen wurden numerische Modelle in Verbindung mit empirischen Daten angewendet. Die wichtigsten Einflußfaktoren für das Versagen der Sturzschächte wurden ermittelt. Es wurde ein Modell zur Beschreibung der Bruchmechanismen und des Versagensablaufs aufgestellt. Dieses Modell wurde verwendet, um die Standsicherheit zukünftiger Sturzschächte zu prognostizieren und um Sanierungsmaßnahmen zu erarbeiten.

Jan 1, 2003

By B. K. Cross

This paper, which adopts a philosophical approach, attempts to analyse the contribution that the computer is capable of making in geological analysis, financial evaluation, and mine project control. Also examined are some reasons for non-utilization of these capabilities. As with most computer associated problems, the cause is primarily human and not mechanical. The paper gives one numerical example of the analysis of geological data and one of the evaluation of mine-design data. The values used in the examples are intended only to emphasize certain points and are not necessarily reproducible.

Jan 1, 1980

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.