Search Documents

By B. M. Wainstein

An extension of lognormal theory and its application to risk analysis models for new mining ventures by B. M. WAINSTEIN*, B.Sc., M.B.A. (Witwatersrand) (Visitor) The lognormal distribution, which remains the most popular distribution model for ore values, is investigated. The T-distribution, an integral part of this theory, is dependent on the sample size, n, and the unknown population parameter, o2, which cannot be integrated out. Hence, o2constitutes a nuisance parameter. In this study, the robustness of the T-distribution to changes in o2 is examined. It is found that the T-distribution is robust for 0,1 <= o2 >= 2,5, a domain covering most practical applications of the lognormal theory. By the use of o2 = 0,7, multiplier factors, which facilitate the computation of the confidence limits, are derived for a comprehensive set of confidence levels.

Jan 4, 1975

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By Z. T. Bieniawski

Estimating the strength of rock materials by Z. T. BIENIAWSKI, Pr.Eng., D.Sc.(Eng.) (Visitor) A practical approach for estimating the strength behaviour of rock materials is presented. The demand for data on rock properties in engineering design is considered, and it is shown that, based on the trends observed in the South African mining industry during the last twenty years, simple and easy-touse methods for the estimation of the uniaxial and triaxial strength of rock materials are needed. It is shown that the uniaxial compressive strength of rock can be conveniently determined from the pointload strength index, which is obtained underground on unprepared rock cores. The triaxial strength of rock can be estimated for most practical purposes from empirical strength criteria. Two such criteria are proposed that allow estimation of the triaxial strength for rock materials to about 10 per cent. The only input required for these criteria is the uniaxial compressive strength. The validity of the practical approach outlined in this paper is confirmed from the experimental tests conducted on some 700 rock specimens representing five rock types. A practical example for the prediction of rock strength is given.

Jan 3, 1974

By F. Riedel

In May 2009 a test work programme was carried out at the sorting laboratory of CommodasUltrasort in Germany which was aimed at establishing the efficiency of X- ray transmission sorting for the recovery of unliberated diamonds in a size range of +8mm. A PRO Tertiary XRT belt sorter with a working width of 600mm and a belt speed of -3mJs was used for the test work. Dual energy X-ray transmission sorting is a type of sensor-based sorting which uses an X-ray scanning system, The attenuation of the transmitting X-rays is measured at two different energy levels, Thereby it is possible to eliminate the effect of the particle thickness on the measurement result. The effective measurement results in a classification by elemental order based on the periodic table.

Jan 1, 2010

With a number of new mines at the feasibility stage and beyond and with several pellet capacity expansions well underway to reduce sintering activity, Alex Broad looks at the impact of worldwide environmental legislation on the iron ore industry. &apos;Environmental impact assessment&apos; has become something of a buzz term in the metals and mining industry over the last few years and is sure to be an integral part of any green or brown-field project worldwide by the turn of the century, if it is not already. Given the number of iron ore projects springing up, most notably in deposit-blessed Australia, it is not surprising that the subject of environmental approval has been raising its green head. At the very least the process can slow down a new mine project, or at worst have it deemed unfeasible but in general a government is unlikely to put up unnecessary barriers to a project with the beneficial financial implications of an iron ore deposit.

Jan 1, 1996

By I. R. Phimister

&apos;Ancient&apos; mining near Great Zimbabwe I. R. PHIMISTER. B.A. Hons. (Nottingham). B.A. Spec. Hons. (Rhodesia) (Visitor) In proposing reasons for the geographical location of Great Zimbabwe, the paper re-examines the popular assumption that Zimbabwe is comparatively remote from the known areas of &apos;ancient&apos; goldmining. The lack of &apos;ancient&apos; workings in the neighbourhood of Zimbabwe is pointed out, and it is suggested that the mining of placer deposits of gold may have played some part in the development of Zimbabwe on its particular site.

Jan 1, 1974

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

Scientific and technical research is becoming an expensive business, and needs to be managed as well as directed. Regardless of whether it operates under public or private auspices, a research-and development organization should not tolerate inefficiency or irrelevance. Its true worth is ultimately decided by the impact it makes on its environment. Doing the right things is preferable to merely doing things in the right way. Clear definition and the setting of goals form the crux of the Management by Objectives (MBO) system. This system provides the research establishment with a profound sense of purpose and direction, which is essential for effective planning and control. Performance standards, in association with costs and manpower, value assessment, feedback, and improvement, tend to follow naturally once the principle of a results-oriented management system is adopted. MBO is a participative management system, leading to decentralization and self-control of the individual rather than imposed control. If wisely implemented with the necessary respect for creative work, it can enhance the job satisfaction of the research worker as well as the overall productivity ofthe research establishment.

Jan 1, 1982

By D. Moradkhani, S. M. Javad Koleini, M. Abdollahy, F. Soltani

"The objective of the study was to determine the type and distribution of rare earth elements (REEs) in the phosphate flotation concentrate from the Esfordi flotation plant in central Iran, in order to understand their leaching behaviour. Samples of the concentrate were prepared and analysed using XRF, XRD, ICP, and EMPA. The Ce, Nd, La, and Y contents were 5608, 2227, 1959, and 679.7 mg/kg, respectively. The main REEbearing minerals in the concentrate are fluorapatite, monazite, and xenotime. Apatite is the chief mineral of the concentrate and the ratio of apatite to monazite is greater than 60. From EMPA analysis, monazite contains a much higher proportion of REEs than apatite, but more than 50% of the REE content of the concentrate is in apatite, as this is the main mineral constituent of the concentrate. During the leaching of REEs in the phosphoric acid production process, more than 99% of the total rare earth values report to the large amounts of phosphogypsum (CaSO4·2H2O) formed during the dissolution reaction. Accordingly, two process options are suggested for treating the Esfordi concentrate. In the first option, the concentrate is treated with 98% H2SO4 at 200–300°C. After digestion and water leaching, phosphorus and REEs are precipitated out of solution. In the second option, the concentrate is treated in a pre-leach stage. The process residue from the pre-leach stage is then subjected to acid digestion at elevated temperature for phosphoric acid production.IntroductionThe rare earth elements (REEs) comprise a set of 17 chemical elements in the periodic table, specifically the 15 lanthanides plus scandium and yttrium. REEs and alloys that contain them are used in devices such as computer memory, rechargeable batteries, cell phones, catalytic converters, magnets, fluorescent lighting, and many more (Krishnamurthy and Gupta, 2004). China supplies about 94% of the REE demand, with the remaining 6% coming from Russia and Estonia, the USA, India, Malaysia, and Brazil (Zhanheng, 2011). Increased industrial development in China has prompted the Chinese government to limit annual export quotas to approximately 35 kt of rare earth oxides (REOs), while non-Chinese annual demand is expected to reach 80 kt by the year 2015. This constriction of supply is being met by the development of many new rare earth mining projects, each of which has its own unique mining and processing challenges (Jordens, Cheng, and Waters, 2013). One of these projects is the Esfordi phosphate project, which is located in Yazd Province in central Iran. The concentrate from the Esfordi flotation plant contains 1.2–1.5% REEs."

Jan 1, 2017

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project&apos;s life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

By J. de Korte, Z. Loubser

"SynopsisThe aim of a blending stockpile is to minimize the natural variation in properties of a material. Two simulation models were written, for coneshell and chevcon stacking, and used to investigate the influence of different stockpile parameters on blending efficiency. The coneshell model is used to show that blending efficiency is highly sensitive to stacked height, with lower output variances observed for higher capacities. Output variance in both models also decreased when the stacker movement increment was decreased. For chevcon stacking, increasing stacker speed significantly increases the blending efficiencies. Increasing the length of the blending tail also reduces output variation, but this parameter would need to be weighed against the accompanying decrease in buffer capacity.IntroductionEven in the most uniform deposit of materials in nature, material properties will vary. The degree of variation can be measured, and usually resembles a normal distribution. The aim of blending and homogenization operations is to minimize the standard deviation of this normal distribution (De Wet, 1994). In general, the reduction in variation will result in a more efficient and cost-effective downstream process. Cement plants need a precise blend of raw materials to ensure desired kiln performance; boilers used in power generation are optimized for fuels of a constant specification; and even though the separation density in a coal washing plant can be adjusted, a constant product quality cannot be produced from highly variable feed (Denny and Harper, 1962). The process efficiency, product quality, and environmental compliance depend on consistency of characteristics in the material fed (Kumral, 2005) Many industries involved in"

Jan 1, 2015

By E. M. Sacris

The semi-autogenous grinding mill is the bottleneck whenever treating hard and finely fragmented ore at Benguet Corporation&apos;s Kaline Concentrator. Low milling rates result from very high and fluctuating mill power draw. Attempts to use a mill horsepower control loop to regulate feed rate were unsuccessful because of operational upsets caused by fluctuations in feed rate on downstream operations. The objective of the computer control was to maximize tonnage throughput by stabilizing the power draw at a high but safe level without upsetting subsequent operations. The semi-autogenous mill is operated in closed circuit with a stationary screen. Instrumentation consists of a feed weightometer, a power transmitter to measure mill load, a headwater flowmeter and an ultrasonic level sensor to measure the mill discharge sump level. A 64 k-byte FOX-3 Foxboro computer processes field data from various sensors and manipulates the input control variables. These variables are the fresh feed rate and the headwater flowrate. Feed rate is controlled through a supervisor-type computer program aimed at maximizing and stabilizing power draw. The control scheme was according to how the operators responded during an operator-directed automatic control mode. Mill dilution is similarly controlled. Results achieved reflect a 3% increase in tonnage milled because of the reduction in control variability that ensued.

Jan 1, 1987

A knowledge of the steady-state mass and energy requirements of a particular process is essential to a determination of the economic feasibility of that process. A predictive simulation technique can be of great value in this respect. A versatile computer program based on a fundamental thermodynamic approach has been developed for the prediction of process requirements. The equilibrium composition of a multiphase system is determined by the technique of free energy minimization. Energy-balance calculations are performed using the appropriate thermodynamic data for the chemical species present in the composite materials used. All models for the process units under consideration are written in modular form, the output being calculated from the input and the specified operating conditions. The computer program is written in such a way that it can be used easily by anyone familiar with the processes involved, even though he may have no previous experience with a program of this type. The program is structured so as to facilitate the varying of one parameter without any alteration to the others, thus simplifying the investigation of the effects of any parameters considered to be important. The program has the advantage of being able to compare existing and new processes on the same basis, namely from the ores to the molten metal.

Jan 1, 1987

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By FT Cawood

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

By R. P. King

"A model of the flotation process can be used effectively for design and control. For design purposes it can be used to predict the performance of a large plant from laboratory and pilot plant data. It can be used for control purposes to assess the utility of any proposed operating modification to an existing plant, and it can also be used to determine optimal control settings for best operating performance.A model has been developed that will allow for variations in feed properties and for variations in fineness of grind. The model can be used to assess the effects of reagent addition rate, aeration rate and pulp level on plant performance and these are the control variables that are used individually or together in all operating flotation plants. The model provides for a distribution in the values for flotation rate constants, particle size and mineral fraction, and, because of its complexity, requires a large computer when it is to be applied to a typical plant configuration. The computational method that is used to apply this model to such configurations is described in this paper, and particular attention is paid to the problem of allowing for feedback of tailings from cleaners and recleaners."

Jan 1, 2014

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By J. Lamb

Project managers must juggle many aspects to bring their project in on time, on budget, and in accordance with the aims of the project owner. Whether the project is a mining feasibility study, a technology implementation or a construction project, it falls to the project manager and his or her team to deal with risk from two standpoints, which may be at odds with one another. First, a project team must deal with risks to the project itself - that is, risks to on-time, on-spec and on-budget delivery against the value promise made to the customer. Second, there is the management of risks within the subject matter of the project, undertaken on behalf of the customer. The project manager cannot dodge this responsibility; yet there is a tendency (particularly in smaller, in-house studies) to avoid digging too deep, possibly for fear of what may be uncovered! This paper investigates the responsibilities of project teams in regard to risk management and reporting. It examines ownership of project risk; the nature of risk management activities undertaken by the team during the course of a project; and outlines some controls to ensure that the two opposing arms of project risk are reconciled for the benefit of both the project team and the project owner.

Jan 1, 2007

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012