Search Documents

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

By I. Grigoriev, A. Yolkin, E. Freiberg, A. Fedchun, A. Kolichko

Abstract: The paper describes the engineering-geological conditions and the structural decisions of the underground machine hall of Rogun HPP under construction in Tadjikistan on Vaksh river as well as the results of physical model studies and long-term in-situ investigations of the variation of the stress-strain state of the surrounding rock mass and the supports of openings, and the assessment of the stability of openings during and after the construction. The analysis of the results of long-term in-situ observations and previous model studies permitted to make the assessment of the present-day state of the machine hall and give recommendations of its further use. Zusammenfassung: Im Vortrag werden die ingenieurgeologischen Bedingungen und konstruktiven Lösungen für die unterirdischen Maschinenhalle des in der Republik Tadshikistan am Fluss Wachsch im Bau stehenden Rogunskaja-Wasserkraftwerkes, die Ergebnisse von experimentellen Forschungen (in physikalischen Modellen) und Naturbeobachtungen der Spannungs-Verformungszustandsänderungen des umliegenden Felsmassivs und Ausbaues von Untertagebauten, sowie Ergebnisse der Bewertung der Standfestigkeit von Untertagebauten während des Bauvorganges und nach der Bauperiode beschrieben. Auf Grund der Analyse von Ergebnissen der dauernden Naturbeobachtungen und früher durchgeführten geomechanischen Modellversuche wird der heutige Zustand der Maschinenhalle des Wasserkraftwerkes bestimmt und werden die Empfehlungen für ihren weiteren Benutzung angeführt. Annotation: L’exposé décrit les conditions d’ingénieur et celles géologiques, et les solutions constructives de la salle des machines de la Centrale hydroélectrique (CHE) Rogounskaya sur le fleuve Vakhch, les résultats d’études expérimentales (sur des modèles physiques) et d’observations extérieures sur place concernant des changements de l’état de tension-déformation d’un massif environnant et du cuvelage des excavations, ainsi que les résultats d’évaluation de la stabilité de l’excavation au cours de la construction et à la période post-construction. A la base de l’analyse des résultats des observations de longue durée et des études préalables géomécaniques sur des modèles, l’évaluation de l’état actuel de la salle des machines de la CHE est effectueé, et les recommandations sur son utilisation ultérieure sont présentées.

Jan 1, 2003

By Q. Fu, Q. Wang, L. G. Wen, M. X. Jia, J. J. Zhao, J. W. Zhou

The BGRIMM process mineralogy analyser (BPMA) is a new automated mineralogy software platform developed in China. This system consists of the BPMA software platform, controlling a combination of commercially available scanning electron microscopy (SEM) and energy dispersive Xray spectrometry (EDS). The BPMA software controls SEM and EDS through their application programming interfaces, to form an auto-SEM and EDS system that automatically acquires BSE images and X-ray spectra, respectively, and classifies minerals by spectrum-matching. After automated measurement and mineral identification, various quantitative process mineralogical data (e.g., mineral composition, mineral abundance, mineral liberation and intergrowth relationships, mineral associations, particle and grain sizes, particle density distributions, calculated assay, elemental deportments, mineral grade recovery and elemental grade recovery, etc.) would be calculated quickly, accurately and automatically. The BPMA could be used for ore characterisation as a new advanced automated mineralogy technology. Keywords: BSE image; X-ray spectrum; automated mineral identification; quantitative mineralogical investigation; automated mineralogy

Jan 1, 2020

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

By A. R. Miller

A fuel cell locomotive incorporates the advantages of its competitors, namely catenary-electric and diesel-electric units, while avoiding their disadvantages. It possesses the environmental benefits, at the vehicle, of an electric locomotive but the higher overall energy efficiency and lower infrastructure costs of a diesel locomotive. The natural fuel for a fuel cell is hydrogen, which can be produced from many renewable sources or via nuclear energy, and thus a hydrogen-fuel cell locomotive will not depend on imported oil. Hydrogen produced from renewable primary energies or nuclear energy would provide a totally zero-emissions vehicle, that is, with zero carbon in the energy cycle. A project partnership among Vehicle Projects Inc of the USA, and South African partners Anglo American Platinum, Ltd, Trident South Africa, and Battery Electric, has designed and is launching a series of five prototype fuel cell-powered mine locomotives.

Jan 1, 2012

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By Brian W. Mackenzie

The mineral exploration environment has observable economic characteristics, the assessment of which provides guidelines for exploration planning in the mining company. The long-term survival of the mining company is directly dependent on successful exploration. Exploration planning contributes to successful exploration through the development of exploration strategies. The objective of exploration planning is to select exploration environments which will enable the mining company to realize best possible profit and corporate risk conditions. Thus, the formulation of exploration strategies is based on profit and corporate risk criteria. Strategic considerations include the selection of commodities as exploration targets, geographic concentration of exploration effort, the realization of acceptable survival conditions, and the structuring of an exploration programme to optimize the economic benefits of the exploration investment process.

Jan 1, 2014

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By P. L. Ngwenyama, I. Maubane

Soundless chemical demolition agents (SCDAs) are proving to be the future of sustainable and environmental-friendly mining. These expansive chemicals become critical when there is a need to break rock close to communities, environmentally sensitive areas, and critical structures and infrastructure. Unlike explosives, the SCDAs do not generate air-blast, ground vibrations, flyrock, noise, dust, and noxious fumes, which can negatively affect the environment, surrounding communities, sensitive areas, and critical structures and infrastructure. Over the years, several types of SCDA products have been used successfully in the civil and construction industries for the demolition of old and dilapidated buildings near vibrations and environmentally sensitive areas. They have also been used to fragment boulders in the mining and construction industries. However, to date, no study has investigated the applications of soundless chemical demolition on a large-scale in opencast mines. Therefore, this study evaluated whether soundless chemical demolition can break large volumes of in situ rock. This was done by conducting five trials using Nex-Pand soundless chemical demolition agents in four different surface mining sites. Trial 1 was unsuccessful as it was unable to break the rock due to the large confinement between the drilled holes and the use of a hole diameter that was 182% larger than recommended. Trial 2 was a success as it was able to fracture the rock with a crack width that reached 110 mm after 72 hours. Trial 3 generated cracks at the biggest hole diameter of 102 mm. The cracks developed and ceased to increase after 96 hours at a crack width of 100 mm. Trial 4 achieved the smallest crack width due to a very competent rock compared to the other sites. Trial 5 generated cracks at a slower rate than other trials because of the use of Nex-Pand powder at lower ambient temperatures than recommended. These trials proved that soundless chemical demolition agents can replace explosives in areas closer to sensitive infrastructure and communities. This will ultimately enable mines to unlock value and access deposits in these areas.

Jul 23, 2025

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By L. A. Maseko

"As part of the mining engineering curriculum, students are required to be placed in industry for vacation work or work-integrated learning (WIL). In this paper we review work-based placement as done at the four South African mining schools: the University of Johannesburg, the University of Pretoria, the University of the Witwatersrand, and the University of South Africa.Key aspects of past and current WIL (pre- and post-graduation) practices that may need attention are highlighted for consideration by all universities that provide professional qualifications. Work-directed theoretical learning, problem-based learning, project-based learning, workplace learning, and simulated work experiences are discussed as legitimate approaches to WIL.Regardless of the choice each institution makes, commitments of universities, preparedness of university teachers, and the desire for equity and excellence will play an important role in the provision of WIL.DefinitionsAccredited Qualification: a qualification awarded on successful completion of an accredited programme.Advisory Boards (or Committees): are essential infrastructure for a WIL curriculum that is built on the integration of the workplace and the university. This requires the collaboration of experts from both environments. Workplace advisors are critical to the success of the academy as they embody expert knowledge of the ‘real world’.Assessment: the process of determining the capability or competence of an individual against standards by evaluating performance.Category: a mode of registration defined in or under the ECSA Act which has a distinctive purpose, characteristic competencies, defined principal routes to registration, and educational requirements.Experiential learning: (in South Africa sometimes used synonymously with work placement or cooperative education) is a term used with a great variety of meanings in the international literature. More broadly, it may refer to learning that has meaningful learner involvement. It is the process of generating meaning from direct experience. In the international literature, experiential learning is learning through reflection on doing, which is often contrasted with rote or didactic learning."

Dec 1, 2018

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By N. A. Barcza

Pointing out that South Africa needs to utilize its wealth-creating activities, together with local and international investment, to further develop its industries, the address asserts that the mining and minerals industries, especially in the manufacture of beneficiated products, offer the greatest potential for South Africa to achieve its goal. As many mineral-beneficiation processes are based on pyrometallurgical routes, the address goes on to describe some historical - pyrometallurgical operations and to indicate probable developments in the future. These include growth in the fields of both precious and base metals. After discussing environmental and recycling matters, together with manpower requirements, the address concludes that the major growth in the mining and minerals industries will occur in the manufacture of steel, stainless steel, ferro-alloys (particularly ferrochromium), aluminium, and titania slag.

Jan 1, 1996

By J. Wills

The use of drilling rigs to increasingly mechanize stope drilling has been acknowledged as important for the S.A. mining industry in it ís efforts to tackle the challenges of low productivity, AIDS and an ageing driller workforce. The spin-offs of increased safety, cost-effectiveness and better mining performance provide advantages to all?from the driller to the shareholder. However, implementation or product rollout has varied from outright success to dismal failure. A study of various cases by Novatek and Anglogold TDS showed clear reasons for these differences. Whereas the successes were characterized by clear objectives, accountability, user buy-in, a commitment to make the technology work and no-nonsense reporting, these were typically absent in failed implementations. The attitude at unsuccessful mines was to ?trial? the equipment?even subconsciously, a ?trial? is a test where failure becomes an acceptable outcome. During the study it became clear that mining management are not adequately trained to manage the often-tricky rollout process. They are often also not empowered or clearly mandated to deal with the organizational, human and technical issues that must dovetail to create a success. The output of the study was to develop a basic rollout process that could be used to formally manage the implementation of new drilling technology. Creating an alignment between the mine, workforce and supplier promotes a win-win situation that will not otherwise spontaneously arise.

Jan 1, 2002