Search Documents

By M. D. Dolan

In this study, the development of a new method for investigating the diffusion of metal cations in multi-component slag systems, using microprobe analysis is discussed. This method allows the analysis of the diffusion of multiple species within a single system. This project has focused on the diffusion characteristics of manganese, iron, calcium and silicon in silicate slags, in order to simulate industrial steel and ferromanganese production. The diffusion behaviour of transition metals is of particular interest because of the effects of their variable valence. This study identified the variation in diffusivity of slag components with changes in composition and temperature of multi-component slag systems. The molecular structure of the experimental calcium-aluminosilicate slags was investigated to determine the chemical and physical properties that influence diffusion behaviour. This experimental data was used to develop predictive models for diffusivity. These models enable the estimation of the diffusivity of many slag components in complex slags, over a range of compositions.

Jan 1, 2004

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By S. A. Villalobos, F. A. Villalobos, and L. E. Aguilera

Rockburst events have been a serious problem for many years in many mines worldwide, and in particular at El Teniente mine in Chile. El Teniente is the largest copper mine in the world, located in the Andes Cordillera where high stress levels are present due to intensing mining activity in addition to complex geology. Consequently, the study and management of the rockburst threat are necessary. In this work, the case of the Diablo Regimiento (DR) mine within El Teniente is studied. The energy capacity of dynamic support systems is determined for different tunnel geometries based on two kinetic methodologies, using data from DR. Initially, rockburst potential is determined by means of a stress analysis around different tunnel geometries through the boundary elements method. In the first methodology a yielding zone (YZ) is estimated for each excavation geometry using the finite element method FEM. The second methodology involves the definition and determination of a critical strain energy (SE) around each excavation geometry using a FEM numerical analysis. In both cases, peak particle velocity PPV is estimated by a scaling law, which is subsequently adjusted due to tunnel amplification effects. According to the results, and knowing the working energy capacity applied in DR mine, it was found that the values of energy capacity for the rock dynamic supports were better estimated by the YZ-PPV approach than by the SE approach.

Sep 1, 2022

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By P. R. Jochhens

The Past. In the past, large metallurgical companies (for example the mining houses) had the necessary infrastructure both to develop metallurgical flowsheets and to undertake the construction and project management of metallurgical plants. Effectively, the sole contribution by contracting companies was the supply, and possibly the installation, of specific items of equipment. OBITUARY: AUSTIN WHILLIER (1927 - 1981) On Thursday, 13th August, 1981, Dr. Austin Whillier passed away peacefully in Johannesburg after a long illness. This event has been a serious blow indeed, and its effects will be felt, not only by the Chamber of Mines of South Africa and the South African mining industry, but also throughout many scientific and technical spheres both in South Africa and further a field.

Jan 1, 1981

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African Platinum Group Metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef-types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky reef is low in chromium and do not pose significant melting problems. Concentrates from the UG-2 reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8-10-9bar at temperatures of 1550°C to 1600°C). During the converting process care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation ofFe2NiO4(trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3. A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Key words: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium.

Jan 1, 2004

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

By M. Berger

The ‘Metallurgical Operations’ Department of Grinaker-LTA Process Engineering (GLTA) currently undertakes then primary mining as well as the re-deposition of tailings forTicor South Africa (Ticor) at their Hillendale mine near Empangeni, KwaZulu-Natal, South Africa. The mining plant, which was designed by GLTA on a Build, Own, Operate and Transfer (BOOT) basis, is capable of mining 780 000 tons per month of ROM material which is then pumped to the Primary Wet Plant for treatment by Ticor. Hydraulic mining via high pressure water cannons and subsequent transfer of the heavy mineral slurry at an RD of between 1.35 and 1.48, has never before been undertaken successfully at this level of production on an in situ reserve. The presentation will take the form of a case study in which the unique site operating conditions will be detailed and discussed, as will the innovative process and engineering solutions employed by GLTA to overcome the engineering and production challenges encountered. In order to protect the intellectual property involved in this operation, this paper is fairly general in nature, and attempts merely to provide the reader with a broad perspective understanding of the operation, and some of the difficulties encountered during the early stages of production.

Jan 1, 2003

By L Singheiser, W. Willenborg, M. Mueller, K. Hilpert

The limitation of fossil fuel resources and the necessity of reducing CO2emission require an increase of the efficiency of power plants by using combined cycle power systems. Pressurized Pulverized Coal Combustion (PPCC) is a potential concept to realise these objectives. The direct use of hot flue gas for driving a gas turbine requires a hot gas cleanup to achieve corrosion prevention of the turbine blading. One of the main problems is the alkali release during the coal combustion process. Molten coal ash slag has a high potential for alkali retention which depend son the alkali oxide activity in the slag. Knudsen Effusion Mass Spectrometry (KEMS) was used to determine thermodynamic data of alkali gas species over molten coal ash slags and of alkali oxides in molten coal ash slags. The main interest of the investigations focused on the structural dependence of the thermodynamic properties of the alkalis. It was found that there is a strong correlation between the thermodynamic properties and the ratio of nonbridging oxygen to tetrahedral oxygen (NBO/T). An increase of the polymerization of the slag results in a decrease of the alkali oxide activity in the slag and thus a decrease of the alkali partial pressure over the slag. Keywords: coal ash slag, structure, alkali oxide activity, alkali vapour pressure, PPCC, KEMS.

Jan 1, 2004

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By Q. X. Yun

This paper provides a new approach to optimize the production planning in underground mines by means of evolutionary algorithms. Firstly, genetic algorithm is used to reach the global optimization in planning. Then, evolutionary programming is employed to obtain the partial optimization for each year. The application proves that the new approach is reasonable and useful. Keywords: Evolutionary algorithm, Genetic algorithm, Evolutionary programming, Optimization, Mining engineering.

Jan 1, 2003

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003