Search Documents

By J. J. Swanepoel

Titanium nitride in upgraded nitrided ilmenite (bulk of iron removed) can selectively be chlorinated to produce titanium tetrachloride. Except for iron, most other components present during this low temperature (ca. 200°C) chlorination reaction will not react with chlorine. It is therefore necessary to remove as much iron as possible from the nitrided ilmenite. Hydrochloric acid leaching is a possible process route to remove metallic iron from nitrided ilmenite without excessive dissolution of species like titanium nitride and calcium oxide. Calcium oxide dissolution results in unrecoverable acid consumption. The leachability of nitrided ilmenite in hydrochloric acid was evaluated by determining the dissolution of species like aluminium, calcium, titanium and magnesium in a batch leach reactor for 60 minutes at 90°C under reflux conditions. The hydrochloric acid concentration (11%, 18% and 25%), initial acid-to-iron mole ratio (2:1, 2.5:1 and 3.3:1), and solid-to-liquid mass ratio (1:8.33 to 1:2.13) were varied. The results indicate that a hydrochloric acid concentration of 25 wt% supplied in a 2:1 acid-to-iron mole ratio would produce the most favourable upgraded nitrided ilmenite product. The dissolution of iron in this solution reached 97 per cent after only 60 minutes. The total dissolution of calcium and titanium species was 0.01 and 0.11 wt% respectively. Hydrochloric acid can therefore be used as lixiviant to remove metallic iron from nitrided ilmenite. Keywords Titanium nitride, upgraded nitrided ilmenite, hydrochloric acid leaching, metallic iron dissolution.

Jan 1, 2011

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By Pieter de Waal

The beneficiation equipment under the control of plant metallurgists exploits the differences in the physical properties between valuable and waste mineral components. In many cases, laboratory results are too late for process control and can only serve the purpose of "post" reports, the calculation of a mass balance and the issue of a quality certificate. As a result, experienced operators regularly adjust separation equipment based on the colour and texture of the various product streams in the beneficiation plant. Metallurgists quickly learn to recognise the different minerals in their ore body. The stereo microscope has been a valuable tool used by operators to quantify known mineral species. For many years it was the only practical method available for the purpose of process control and even for quality contro1. The modem spectroscope is far superior to the human eye and can rapidly detect a change in mineral composition. New generation optical scanners and digital signal processors can provide useful signals, related to mineral composition that can readily be applied for the purpose of process control. Successful case studies, covering dry in-line and slurry applications as well as in-plant fast spot analysers are presented.

Jan 1, 2014

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

By M. Kumral, Y. A. Sari

Underground mining operations tend to have higher operating costs than surface mines. When metal prices decrease, profitability is jeopardized due to the high costs. Therefore, mining management harnesses new practices that increase operational efficiency. One way to manage this challenge is to invest in new mine planning practices. Stope layout optimization as a part of underground mine planning aims to identify a portion of the orebody in the form of production volumes (stopes) to maximize profit under roadway and stope dimension constraints. In this paper we propose a novel approach based on identifying ore-rich areas of the deposit and prioritizing their extraction through an iterative heuristic clustering approach. The proposed approach is compared with and validated by an exact method through a small mining example. The heuristics produced nearly identical results in a very short time. Finally, a case study was carried out using a larger data-set. The cluster-based iterative approach generated nearoptimal stope layouts in a computationally effective manner.

Mar 1, 2021

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003