Search Documents

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021

By J. W. S. Koel, T. R. Twidle, P. C. Engelbrecht

The process flows of the three flotation circuits at the concentrator of the Black Mountain Mineral Development Company (Pty) Ltd are described. Because of the complexity of the circuits and the associated reagent regime, the plant is equipped with a comprehensive range of control equipment. The different process-control strategies are discussed, and the modifications that have been necessary to the stabilizing control loops in the copper, lead, and zinc flotation circuits are shown in detail. It is concluded that the control strategies have continued to bring about benefits and improvements to the process.

Jan 1, 1986

Bateman Engineering managed the establishment of a second diamond treatment plant at the Letseng Mine in the Mokhotlong District of northern Lesotho, about 100 km from the town of Buthe Buthe. Letseng Diamonds Proprietary Limited, is owned 70 % by Gem Diamonds and 30 % by the Government of the Kingdom of Lesotho. The second plant, which commenced construction in late 2006, doubled Letseng Mines' hard rock processing capacity from 2.6 million t/yr to 5.2 million t/yr, making it the worlds' seventh largest diamond mine by throughput. Bateman Engineering provided the engineering design, procurement and construction management of the new plant.

Jan 1, 2010

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

By G. Chambovet

Applied geophysical methods such as the surface seismic method have been applied for many years and in many places, mainly for oil exploration and to a lesser extent for mineral deposits? exploration in sedimentary basins. The seismic method fundamental is based on the variations of acoustic impedance in a layered earth model and such variations at each main geological interface create reflected waves that are processed and imaged in order to output a clear picture of the subsurface structure. The geology of South Africa was historically, and even until recently, considered as unfit for seismic exploration and the mines were always reluctant to spend any portions of their exploration budgets on these techniques. Hard rocks and high P-waves velocities were creating quite a hopeless model for any mine geologist or geophysicist (if any), unsuitable for the proper use of seismic waves to image their subsurface problems. Boreholes were considered the only reliable tool to derive a geological image of the mine structural features and were linked sometimes with surface methods such as aero-magnetism. The obvious flaw of this methodology was the inability to derive a continuous image from a discrete set of measurement points. Surface 3D seismic is the tool that gives a reliable solution from the initial model extracted from the boreholes, as even the aero-magnetism mapping gives a flat image, unable to show any depth correlation from well to well. The first 3D surface seismic surveys were recorded in the early Nineties only for the gold mines of the Witwatersrand, after a series of serious new shaft sinking failures. The wrong geological locations of these shafts resulted in financial loss of several hundred million rands. The era of3D seismic just started in South Africa and till 1997, all seismic done in the country was for gold exploration with geological target depths close to the oil exploration average depth of investigation. A very important breakthrough was reached when the depth accuracy of the seismic image was tested in real scale as the stopes were surveyed. An error of amplitude of 20 m was usual when true depth was compared with the seismic image predicted depth and shape. This accuracy, completely unknown in oil exploration, started to gain supporters of seismic methods in the mining community but the cash problems and the concentration/disappearance of gold mines in the late Nineties, led to the belief that seismic would be just a very short exploration activity for the mining sector. ort exploration activity for the mining sector. But starting in 1998 with Impala, a tremendous and continuous 3D surface seismic activity occurred in the platinum mining sector. The seismic world got used to new terms such a Merensky and UG2, which have replaced the VCR and black reef. If the primary expectation of platinum surface 3D seismic was to determine and ascertain new shaft locations, as for the gold mines, the quality of seismic data led the mine geologists to require smaller and smaller imaging of geological objects. In addition to the main structural image, small faults, potholes, and shear zone were common expectations of platinum seismic. In a constant velocity environment, what saved the day was the sharp density contrast between the PGM reef and the embedding geology. A good contrast of impedance exists in the whole Bushveld and is sufficient to have enough reflected waves from the PGM main layers to build a high quality seismic image of the subsurface. Recent advances in technology have led in less than 10years to major improvements in the seismic acquisition by using high frequency vibrating seismic sources, but also in processing and interpretation. With these latest improvements, seismic can detect objects of 7.5 m size, either fault throws, flexures, etc. The PGM formations of the Eastern limb of the Bushveld Complex are now accessible for seismic imaging, with cost per square kilometre comparable to the borehole cost of the same surface unit. The economically acceptable seismic surveys can be used for UG2 structural imaging up to a depth of 210 m below surface. Linked with borehole information, 3D seismic today offers a wide range of information for mine development: structural imaging, small fault detection, pothole and shear zone identification. All users of 3D seismic have also used this technique as a tool in the process to qualify their mineral reserves and especially from the category ?inferred? to the category ?measured?. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. The current high demand on platinum, pushes the seismic towards new technologies to be implemented in order to improve the final image. Using surface and borehole seismic together or acquiring seismic surveys with multi-component receivers have been just introduced in South Africa. In less than 10 years, surface seismic by adapting its methods to the special case of the Bushveld, became a mandatory step in mine development and ore resources evaluation. As part of the ?seismic? world we are proud to be a major player the ?surge? of platinum exploration and production in these last years and we will certainly increase our synergy with the mine sectors in the exciting coming years.

Jan 1, 2006

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By A. Dienenthal

"The casthouse floor has always been one of the most dangerous working places on a blast furnace or a ferro-alloy/nonferrous furnace. Apart from working in an atmosphere including toxic gases, fumes, and dust, the workers have to perform hard and heavy manual work close to runners and ladles filled with hot liquid metal and slag.Before the invention and installation of tapping equipment the tap-holes were opened and closed manually. Opening was done by means of steel bars and sledgehammers, whereas the tap-hole was closed by repeatedly ramming small amounts of clay or refractory material into the tap-hole, again with the help of long, heavy bars. In addition, on blast furnaces the blast had to be stopped, since it was impossible to close the tap-hole properly against the blast furnace pressure. This stoppage of the blast resulted in regular losses of production. Around 1900 a major change in technology occurred. Samuel W. Vaughen, superintendent of the blast furnace department of the Cambria Iron company at Johnstown, Pennsylvania (USA), invented the first clay gun in 1895 (Wiley, 1896) (Figure 1)."

Jan 1, 2014

By D. F. Malan

This paper provides an overview of the concepts of citations and journal impact factors, and the implications of these metrics for the Journal of the Southern African Institute of Mining and Metallurgy (JSAIMM). Two key research literature databases publish journal impact factors; namely, Web of Science and Scopus. Different equations are used to calculate journal impact factors and care should be exercised when comparing different journals. The JSAIMM has a low impact factor compared with some of the more prestigious journals. It nevertheless compares well with journals serving other mining sectors, such as the Canadian CIM Journal. The problems associated with journal impact factors are discussed. These include questionable editorial practices, the negative impact of this concept on good research, and the problem of a few highly cited papers distorting the journal impact factor. As a consequence, there is growing resistance to the use of journal impact factors to measure research excellence. The San Francisco Declaration on Research Assessment is a global movement striving for an alternative assessment of research quality. As a recommendation, the Editorial Board of the JSAIMM should adopt a pragmatic approach and not alter good journal policies simply to increase the journal impact factor. The focus should remain on publishing excellent quality papers. Marketing of the Journal, the quality of the published papers, and its open access policy should be used to counter the perception that journals with high impact factors are better options in which to publish good research material.

Sep 1, 2022

By R. Armstrong

The stability of rock slopes is significantly influenced by their curvature in plan view. The importance of this in open pit mining is indicated by the fact that, in a deep pit, steepening of the slopes by 1° may save as much as $100 million. It is considered that there are two significant factors that play a part in the influence of plan curvature. These two factors are the effect of stress, and the effect of geological structure. The scant literature that pertains to this aspect of rock slope design was reviewed. The geometrical influence of the plan curvature was then investigated. It was seen that it has a parabolic effect on the maximum possible wedge that can fail into a circular pit, where the tighter the concave curvature the smaller the wedge. The plan curvature also affects the volume of a particular wedge, where concave slopes result in an exponential decrease in the volumes and convex slopes have exponentially increased wedge volumes. A change in the strike of the wedge did not affect the curvature’s influence on the volume, but the volumes of shallower dipping wedges were affected more by the influence of the plan curvature. La stabilité des talus des roches est très influence par la courbure de celles ci dans la vue en plan.Son importance de l peut arriver à sauver même $100 millions. Il est considère qu il y a deux facteurs importants qui jouent une influence sur cette courbure. Il s’agit de l’effet des contraintes et l’effet de la structure géologique. La brève littérature qui se réfère à cet aspect du conception sur le talus des roches a été revue. L’influence géométrique de la courbure des plans a été investiguée. Il a été vu que cela un effet parabolique sur la bosse ou le su relèvement maximum possible qui peut faillir dans un puits circulaire, ou le plus resserre est la courbure concave, le plus petit est su relèvement (bosse). La courbure plane aussi affecte le volume d’un particulier su relèvement ou les talus concaves résultent dans une décroissance exponentielle en volume alors que les talus convexes accroissent la volume de ces su relèvements (bosse). Le changement de l’orientation de la bosse (su relèvement) perpendiculairement ou obliquement n’ a par affecte l’influence de al courbure sur le volume mais les volumes des bosse (su relèvement) peu profonds étaient affectes par la courbure des plans. Die Stabilität der Felsensteigungen wird erheblich durch ihre Biegung im Plan beeinflußt. Der Wert von diesem in der Tagebaugrube wird durch die diese Tatsache, in einer tiefen Grube, steepening der Steigungen durch 1° angezeigt; kann soviel wie $100 Million speichern. Es wird betrachtet, daß es zwei bedeutende Faktoren gibt, die eine Rolle im Einfluß der Planbiegung spielen. Diese zwei Faktoren sind der Effekt des Druckes und der Effekt der geologischen Struktur. Die dürftige Literatur, die diesen Aspekt des Felsensteigungdesigns betrifft, wurde wiederholt. Der geometrische Einfluß der Planbiegung wurde dann nachgeforscht. Es wurde gesehen, daß es einen Parabolischen Effekt auf dem maximalen möglichen Keil hat, der in eine kreisförmige Grube ausfallen kann, wo, das fester die konkave Biegung, das kleiner der Keil. Die Planbiegung beeinflußt auch das Volumen eines bestimmten Keils, in dem konkave Steigungen eine exponentiale Abnahme an den Volumen ergeben und konvexe Steigungen exponential Keilvolumen erhöht haben. Eine Änderung im Schlag des Keils beeinflußte nicht den Einfluß der Biegung auf das Volumen, aber den Volu

Jan 1, 2003

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023