Search Documents

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020

By W. K. Brinsden

In August 1965, the late Mr Alan Smith, then Mill Superintendent at Gold Mines of Kalgoorlie (GMK), Australia, asked me to investigate the planting of vegetation on the GMK slimes dams in order to ease the dust problem in urban and industrial areas-a problem that is caused largely by dust from these barren slimes dams. My early sources of information were the comprehensive papers in various issues of the Journal of The South African Institute of Mining and Metallurgy. However, the climate of Johannesburg differs from that of Kalgoorlie. The average Johannesburg rainfall, which falls mostly in summer, is 730 mm, and the average maximum summer temperature is 26°C (top 34°C). The winters are cool, the average maximum being 18°C (low -7°C). Kalgoorlie, on the other hand, receives, on average, 257 mm of sporadic rainfall, has hot dry summers with an average maximum of 35°C (top 45°C), and cool winters with an average maximum of 18°C (low -2°C). My obvious choice was to look at established trees growing on the GMK lease. A number of Athel pines were growing vigorously adjacent to the Oroya mining and geology offices and also on a nearby sand dump. The Athel pine (Tamarix aphylla), which is native to North Africa, Asia, and India, was originally introduced into Australia in 1936 by Mr Essington Lewis, then manager of BHP. His cuttings were planted in Whyalla, where some difficulty had been experienced in finding trees and shrubs that would flourish despite the district's low rainfall. In August 1965, cuttings of approximately 20 cm length and 1 cm diameter were taken from the GMK trees, stripped of leaves, and placed in jars of water in the sun. When the cuttings had sprouted both leaves and roots, they were planted in local soil in tins (about 20 cm high and 10 cm in diameter), and watered daily. In October 1965, when the new shoots were about 8 cm long, the trees were transplanted onto a lower flat section¬approximately 30 m wide, 30 m long, and 2 m high-of the Trafalgar slimes dam. No additional soil or fertilizer was used, and the trees were planted in their tins, the bases of which had been removed (the tin would eventually rust away). A few common varieties of non-prickly cactus and two native salt bush (spp Atriplex) were also planted, but did not survive, probably because of the acidity of the slime. During the summer of 1965/1966, Kalgoorlie's rainfall was 88 per cent above the average, and this probably helped the trees to survive. The moisture content was usually about 2,5 per cent from about 10 cm below the surface, and the pH value of the slime (d80 approximately 75 µm) was about 6. The trees were watered twice a week for the first four months and then left untended. By 1974 they had grown to only about 0,7 m, which indicated that their growth in slime was very slow. Other Athel pines were planted on the wall of the dam, but did not survive beyond 1974, probably because of the steep (about 500) slope and the hardness of the walls, which were initially formed by hand-shovelling of the slime as the height of the dam was raised. Five of the six Athel pines planted in 1965, which probably reached maturity (approximately 5 m in height) in 1981-16 years after being planted-have survived. In the early 1980s, waste rock had to be dumped on the dam, but the management of KMA (now KCGM) took care to ensure that the trees were not buried. Trials are being conducted on other tailings dams so that the performance of cuttings taken from the trees on Trafalgar dam can be compared with that of cuttings taken at various sites in Western Australia. It might also be worth while for an attempt to be made to strike cuttings from Trafalgar dam in pots containing different mixtures of soil and slime.

Jan 1, 1991

2nd CONGRESS OF THE INTERNATIONAL SOCIETY FOR ROCK MECHANICS The 2nd Congress of the International Society for Rock Mechanics will be held in Belgrade, 21-26 September, 1970. The Congress will include: working sessions, study tours, receptions, excursions introduced in the working sessions and post-congress excursions and special programme for accompanying persons. Anyone interested in rock mechanics and its applicarion may take part in the 2nd Congress. Official languages of the Congress are: English, French and German. Simultaneous translation service will be provided during the Congress. All the correspondence concerning the 2nd Congress of the International Society for Rock Mechanics should be addressed to: Sekretarijat 2. kongresa Medjunarodnog drustva za mehaniku stena Institut za vodoprivredu "Jaroslav Cerni" Bulevar vojvode Misica 43, Postanski fah 530 Beograd - Jugoslavija NINTH INTERNATIONAL SYMPOSIUM TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of June 14-19, 1970, follows the Computer Symposium held in Salt Lake City this year. The purpose of the Symposium is to define the role of decision making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-allows a complete picture of the mineral industry in its public policy, corporate, financial and technological environment to emerge. This is another of the series of symposia on this and related subjects started in the early 1960's at the University of Arizona. Sponsorship has included a number of Universities and the Society of Mining Engineers of the American Institute of Mining. This 1970 symposium is the first to be held outside of America, and is being sponsored by the Canadian Institute of Mining, McGill University and Ecole Polytechnique. A number of delegates from South Africa have participated in these symposia and several have already arranged to attend this symposium in Montreal. Enquiries should be directed to: Secretariat, The 9th International Symposium, Department of Mining Engineering, Ecole Polytechnique, P.O. Box 50l, Snowden, Montreal 248, Quebec, Canada. 24th INTERNATIONAL GEOLOGICAL CONGRESS This Congress is to be held in Montreal, Canada, from August 21 to 30, 1972. A very detailed and extensive programme has been proposed, and includes a number of excursions. Copies of the first circular are obtainable from: The Organizing Committee, 24th International Geological Congress, 601 Booth Street, Ottawa 4, Ontario, CANADA. SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg on 12th to 13th June 1969 are now available. Copies may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal at a cost of R10.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). 'The world sulphur position,' by W. C. J. van Rensburg (Member). 'The South African sulphur position,' by D. L. Taylor (Member). 'The recovery of pyrite at Government Gold Mining Areas Limited,' by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. R. Carlisle (Member). 'Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment,' by W. A. Gilbert (Visitor) and E. A. Nugent (Member). 'The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process,' by D. J. Tutt (Associate Member). 'Pyrite recovery by jigs at Durban Roodepoort Deep Limited,' by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). 'The storage of pyrite concentrates,' by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). 'The flotation plants of the Anglo- Transvaal Group,' by L. A. Bushell (Member). 'Pyrite flotation with amines and cyanidation of the products,' by E. H. D. Carman (Member). 'Gold recovery by cyanidation from mill products obtained after pyrite flotation,' by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). 'The influence of sulphydral and cationic flotation reagents on cyanidation of native gold,' by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). 'Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector,' by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy).

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

Branch Minutes of the General Meeting held at President Steyn Gold Mine canteen on Wednesday, 10th May, 1978, at 4.00 p.m. Erratum We apologize to Mr J. G. Taylor for the error in one of his qualifications. Bio-engineering monograph The selection of papers presented at the International Bio-engineering Conference at the University of Cape Town organized by the South African Institution of Mechanical Engineers and held in April 1977, and which are appearing in The South African Mechanic al Engineer during April to June this year, will shortly be available in book form. Mathematics The Institute of Mathematics and Its Applications is planning the following conferences and symposia: The Nand F Proposals in Relation to Mathematics, 1st July, 1978: London School of Pharmacy. NIM reports Report no. 1917 The instrumental neutron-activation analysis of granites from the Bushveld Complex. (31st Mar., 1978.) Report no. 1951 Potentialities and limitations of four-parameter equations for the correlation of formation constants of metal-ion complexes in aqueous solution.(15th May, 1978.) Report no. 1963 An evaluation of the methods used at the National Institute for Metallurgy for the analysis of base-metal concentrates. (28th Apr., 1978.) Report no. 1964 The separation, by anion exchange, of noble metals on substituted cellulose. (28th Apr., 1978.) Guide To The Preparation Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1978

By B. B. Tati

The project report is based on vacation work done by the writer at the Khutala Colliery during December/January 2009?2010. The purpose of this report is to explain and describe the design process in a multi-seam mine design for coal extraction at the Khutala Colliery. The multi-seam design will focus on the No. 2 and No. 4 seams as these are the seams that are currently being mined by underground methods at Khutala Colliery. The seam thicknesses and the parting thickness between the seams provide suitable conditions for designing a multi-seam mine design. An investigation into the pillar design aspects is carried out followed by a numerical modelling analysis of various scenarios. This analysis validates the first principles approach provided by multi-seam design guidelines. The design results from the analysis of the selected pillar design indicate sufficient parting for primitive conditions between seams, thus illuminating the need for superimposing in-panel pillars. This multi-seam mine design confirms the potential for the extraction of coal in a new panel. The design indicates that significant amounts of power station coal are present and suitable for extraction by room and pillar mining methods. The panel block indicates 401 625 tonnes of ROM coal. This block has a life of panel that will be mined just over a 4-month period. This 4-month period is assumed to mined at a production rate of 48 000 tonnes per month. The total capital cost required for the new panel is R48 281 127.05. Keywords Multi-seam mining, panel design, ventilation flow, superimposition.

Jan 1, 2011

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

Written contribution by J.F. Curtist The paper is an interesting exercise in the application of mathematics to a theoretical situation presumed to oc¬cur underground. However, some of the assumptions on which the calculations are based are unlikely to occur in any actual mining situation. Assumptions made in the paper Objections to these assumptions are noted seriatim. (1) `it is assumed that any loading-rate effect will be small and can be ignored' (p. 3). A loading rate of the order of 50 kN-12 per cent of the maximum load-is customary to prevent the props being dislodged by the blast. (2) `it is unlikely that all the props will be installed with their full stroke available, but for the purpose of this analysis, it is assumed that this is the case' (p. 3). A more reasonable assumption would be that, with the most careful selection of prop length and the most rigid control of stope width, the available stroke length would on average be reduced by the order of 70 mm on installation-20 per cent of full stroke. (3) `each support unit supports a block of 3,3 m2 bound¬ed by vertical fractures with zero cohesion that are parallel and at right-angles to the stope face respec¬tively' (p. 5). Joughin and Jager have shown this to be an unwar¬ranted assumption in respect of the positioning, the direction, and the dip of the fractures present in a stope in rockburst conditions. If, as assumed, there was `zero cohesion' between such blocks, the removal of a hydraulic prop in row 3 supporting such a block would ensure that it fell out before a profile prop could be installed in the same position. (4) `the height of each of these blocks is 3,0 m, the volume of each block is 9,9M3, the mass of each block is 27 225 kg' (p. 5). The concept of individual props being affected by dis¬crete blocks of known and uniform dimensions of relatively low ground velocities (less than or equal to 2,16 m/s) acting in line with the axis of the prop is one that lends itself to neat mathematical calcula¬tions. It does not, however, bear much similarity to the actual conditions that are exposed underground in excavations where rockbursts occur. Ortlepp and co-workers concluded that `the impulse of the shockwave can cause the displacement of the

Jan 1, 1991

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as the capacity of the laboratory to process the samples within a given timeframe. In general terms, grab sampling is known to be problematic because samplers tend to over sample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five percent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given with respect to the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2009

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004