Search Documents

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

By X. M. Prevost

A computer system to store, retrieve and process coal borehole and analytical data together with other geological, geographical or topographical information is described. As a result of the large volume and variety of data stored since its inception in 1979, as well as the basic versatility of the system, the National Coal Data Base has been performing a number of new tasks for which it was not originally designed. As considerable sets of data are used on almost every project, the use of statistical application programs has become an important processing tool.

Jan 1, 1987

By P. G. Mason, H. T. Brown

Electrowinning of nickel at the Bindura Smelting and Refining Company by H. T. BROWN, B.Sc. (Member) and P. G. MASON, B.Sc. (Member) After a brief discussion of theoretical considerations in the electrowinning of nickel, an account is given of the electrowinning process and plant used at the Bindura Smelting and Refining Company.

Jan 2, 1977

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions.

Jan 1, 2012

By D. Menne

An empirical dimensionless correlation is presented that relates system variables to the superficial slip velocity between solid mineral products and an interstitial fluid. The correlation is valid within engineering accuracy for all solids and fluids at all concentrations. The particular usefulness of the correlation is that it provides explicit equations for both slip velocity and voidage.

Jan 1, 1983

By D. H. Batchelor

Efficient modern-day mining operations are turning increasingly to technology to combat rising operating costs in an adverse economic climate for the industry. Computerised truck dispatching is one such technological advance that has enhanced the efficiency of the mining operation at Palabora. The economic incentives, basic operation and general system benefits of Palabora's computerised truck dispatching system are considered.

Jan 1, 1987

By R. Hope, C. van Heerden

In any process or organization inefficiencies are costly. In times of abundance this reality often does not receive much attention. During such times the focus is rather on increasing capacity to increase production. However, there is a growing awareness in the world of tougher economic, social as well as environmental conditions, and enterprises find themselves facing greater demands for accountability towards shareholders, the environment and the public, as well as growing competition for market share and limited global resources. This reality is no different in ensuring a sustainable mineral sands operation. In order to achieve this, any operation needs to be stripped of all process as well as operational inefficiencies. In this context it has become essential for any Mineral Separation Plant (MSP) to have the necessary process monitoring and control systems in place to continually monitor and optimize the production of on-spec products and maximize operational efficiency and consistency. The MSP Grade Control Solution developed by Crusader Systems and running on top of the CSense platform contributes towards these goals by improving the consistent production of on-grade product. This allows the process to operate closer to the maximum allowable product grade constraint, which in turn maximizes production.

Jan 1, 2003

By Kurt RP Petersen, Hendriena van der Walt

With the decline in fine diamond production from the Argyle mine in Australia, there is a greater emphasis on efficiently treating the finer size fractions through a DMS circuit. Although it is generally well understood that smaller diameter cyclones are more appropriate for this application, practical results do not necessarily meet this expectation. In this paper the operational performance of particular sized cyclones throughout the group was compared. Based on the results there is evidence that under certain practical operating conditions, small cyclones are not necessarily best for fine size particle treatment, particularly given the production pressures faced by all mines. However, there seems to be considerable merit in using larger sized cyclones, which tend to exhibit less performance variability, irrespective of operation conditions.

Jan 1, 2006

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By A. B. Stewart, I. J. Barker

Traditionally it has commonly been believed that the only problem with inductive reactance in a submerged-arc furnace is that it leads to difficulties with the electricity supply as a result of the Iow power factor. This paper sets out to show that inductive reactance can also give rise to the following problems in the metallurgical operation of a furnace: (i) dead and live phases (fairly well known in openarc furnaces), (ii) lack of sensitivity to electrode movement, (iii) interactions between electrodes. These problems increase with increasing inductive reactance relative to resistance, and thus they increase with furnace size. Each of these effects is discussed in detail, and suggestions are made for their alleviation.

Jan 1, 1980

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By S. Neilson, M. G. Demmer, K. McCarogher

The Phoenix Programme takes the Mining and Mineral Processing Industry into the Science Classroom In the early years of mining, methods were crude, simple, labour-intensive, and very slow. Human resourcefulness, however, created innovations (mechanization, and computerization), that resulted in faster development, greater tonnages of ore, more efficient separation, and a superior final product. This expansion occured an ever-increasing rate, and resulted in a booming mining industry and a growing economy.

Jan 1, 1989

By R. T. Muller

Contribution to the above paper by R. T. Muller (Visitor) Demands are being made and pressure is being brought to bear on employers in South Africa to narrow or eliminate the wage gap between their White and Black employees. Few thinking people will dispute the fact that a constant improvement in the wages of Black personnel is essential, but this cannot be done merely by a redistribution of income in South Africa.

Jan 7, 1974

By M. G. Spengler

Mr More O'Ferrall must be complimented on a paper that will be a useful reference for the re-working of previously abandoned workings. His paper so closely mirrors experiences at East Rand Proprietary Mines, Limited, that it could well have been based on occurrences in that mine. Corrosion The Scientific Society of Mechanical Engineers is organizing the 115th event of the European Federation for Corrosion in Budapest, from 18th to 22nd October 1982.

Jan 1, 1981

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006