Search Documents

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By N. Andersen

During the preliminary design phases and feasibility study of a proposed vertical shaft, a vertical diamond drill-hole is normally drilled on the site. This paper outlines how rock mass characteristics, in-situ rock stress, rock strength, hydrological characteristics, and structural parameters can be determined using wireline logging of this borehole. In addition, a rock mass classification scheme is developed, based on published work, and in particular the Q-factor is adapted to assess the stability of raise-bored shafts. The ‘stick plot’ is introduced, which combines all geotechnical parameters applicable to the stability of a vertical shaft into a colourcoded format where cross-correlations can readily be made on a day-today basis during the shaft-sinking process.

Jan 1, 2015

By E. Pizarro, A. Videla, G. Compan

One of the main problems related to mining investment decisions is the use of accurate prediction models. Metallurgical recovery is a major source of variability, and in this regard, the Chuquicamata processing plant recovery was modelled as a function of geomining-metallurgical data and ore characteristics obtained from a historical database. In particular, the dataset gathered contains information related to feed grades, ore hardness, particle size, mineralogy, pH, and flotation reagents. A systemic approach was applied to fit a multivariate regression model representing the copper recovery in the plant. The systemic approach consists of an initial projection of the characteristic grinding product size (P80), based upon energy consumption at the particle size reduction step, followed by a flotation recovery model. The model allows for an improvement in the investment decision process by predicting performance and risk. The final geometallurgical model uses eight operational variables and is a significant improvement over conventional prediction models. A validation was performed using a recent data-set, and this showed a high correlation coefficient with a low mean absolute error, which reveals that the geometallurgical model is able to predict, with acceptable accuracy, the actual copper recovery in the plant.

Jan 1, 2015

By G. Hangone

Paper written on project work carried out in partial fulfilment of MSc thesis This paper investigates the effects of thiol collectors: xanthates, dithiophosphates, dithiocarbamates and mixtures of these on the froth flotation performance obtained with a bornite-rich copper sulphide ore from Okiep Copper Mine with a feed grade of 1.8%copper. Batch flotation tests were used to assess the performance in terms of mass-water recovery, sulphur grade-recovery and copper grade-recovery relationships and the Klimpel rate constant for copper recovery. The results showed that the di-ethyl-dithiocar-bamate (di C2-DTC) was the weakest collector of copper sulphide minerals. Highest copper recoveries were obtained with the di-ethyl-dithiophosphate (di C2-DTP), which were accompanied with more watery froths and lower copper grades demonstrating frothing properties in addition to collector action. Superior copper recoveries were obtained with the 90% ethyl xanthate (C2-X):10% di-ethyl-dithiophosphate (di C2-DTP) and 90% ethyl xanthate (C2-X):10%di-ethyl-dithiocarbamate (di C2-DTC) collector mixtures compared to that obtained with ethyl xanthate at an equivalent collector dosage of 0.139 mol/ton ore (a dosage equivalent to 20 g sodium ethyl xanthate per ton ore). A superior copper grade was obtained with the 90% ethyl xanthate: 10% di-ethyl-dithiocarbamate collector mixture at a dosage of 0.0695 mol/ton ore compared to that obtained with ethyl xanthate at the same equivalent dosage. Keywords: flotation, collector mixtures, copper sulphide ore

Jan 1, 2005

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006

By D. B. Swanepoel

Hulamin Rolled Products (Ltd) developed a high Mn and Si containing alloy, EN 4017 as a scrap consuming alloy from the waste generated in producing their range of clad products for brazing of inter alia automotive heat exchangers. The multifaceted composition of this alloy (Al -1.2 wt% Si -1.1 wt% Mn -0.2 wt% Mg-0.26 wt% Cu) suggested that it might display some degree of strengthening via precipitate formation of the Mg2 Si-types. The aging isotherms constructed showed that EN 4017 with 0.19% Mg reached a lower peak strength (YS~210 MPa and UTS~260 MPa)compared to the EN 4017 material with 0.43% Mg (YS~270 MPa and UTS~325 MPa). The higher Mg variant of EN 4017 was comparable with the age-hardenable reference alloy EN 6061. Selected area electron diffraction (SAED) studies proved that the microstructure of age hardened EN 4017 contained a combination of ß', ß" and U2 phase after being aged at 175ºC for 65 h. The general microstructure contained precipitate free zones as well as grain boundary Si films, although these did not lead to significant embrittlement. The role of Mn dispersoids in the fracture mechanism of 4017 is also discussed. The article will compare the behaviour of EN 4017 with that EN6061. Keywords: Age-hardening, dispersoids, magnesium silicide, precipitate free zones

Jan 1, 2009

By J. A. Cruise

With the end of the official apartheid legislation in the early 1990s, South Africa was heralded as a non-racial country. However, racial awareness has been reintroduced into the country with the Affirmative Action and Black Economic Empowerment legislation. Gender and racial transformation are the current order of the day. All organizations are required to reflect in their make-up the demographics of the population as soon as possible. Scorecard shave been drawn up to measure the rate of transformation for gender and race in organizations. The mining industry in South Africa has been in the forefront of this transformation legislation and scorecards. This paper seeks to show the effect of gender and racial transformation on mining engineering education and professionalism by analysing the changing demographics of graduating mining students at both the South African universities offering a degree in mining engineering, the professional registration of mining engineers with the Engineering Council of South Africa (ECSA), and the membership of the Southern African Institute of Mining and Metallurgy (SAIMM), the vocational institute for mining engineers. It also demonstrates the absurdity of gender and racial quotas based solely on the demographics of the current population of the country. This paper shows the degree to which mining engineering has transformed in both gender and race.

Jan 1, 2011

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By M. R. Khalesi, Y. Kianinia, A. Seyedhakimi, F. Soltani

"The feed ore to Agh-Darreh gold processing plant (Takab City, Iran) contains 2 ppm Au, 7 ppm Ag, and 120 ppm Hg. After cyanide leaching of the feed at pH 10.4, 80% of the total mercury (in the form of cinnabar and metacinnabar) goes to the tailings dam. In this research, separation of mercury from the tailings by flotation was investigated. The effects of collector type and dosage, pH, and the number of cleaner stages were studied. The results showed that after two stages of cleaning a 40–62% recovery of Hg at a grade of 14.3% Hg is attainable. Recycle water from a test in which 50 g/t amyl xanthate and 30 g/t pine oil was used in the flotation stage showed no adverse effect on the leaching and adsorption of gold onto activated carbon.IntroductionMercury, most commonly found in the nature as the mineral cinnabar (HgS), is a hazardous substance because of its mobility and toxicity (Kyle et al., 2012). Roasting is the wellestablished treatment method for mercury ores, in which the sulphur is burned and volatilized and mercury recovered subsequently by cooling and condensation. However, for low-grade ores, flotation is mainly applied for primary concentration due to its comparatively low costs, low environmental hazards, and flexibility regarding feed variations (Bulatovic, 2007). Particularly, cinnabar can be easily recovered by flotation using pine oil and a collector such as xanthate (Bulatovic, 2007; Crozier, 1991). Floatability of cinnabar is reduced due to surface oxidation when it is exposed to the atmosphere after crushing. This problem can be eliminated by adding copper sulphate and lead nitrate or acetate. The best pH for cinnabar flotation is in the range of 6.5 to 8.5 according to Erspamer and Wells, (1954), who reported that cinnabar and stibnite can be floated with long-chain xanthate collectors and an alcohol frother, with cumulative recoveries of 97.8% and 94.7%, respectively. Lead acetate was used as an activator."

Jan 1, 2017

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By E. Harris

Frithia humilis is an endangered succulent plant species. Its distribution range overlaps with the coal fields of Mpumalanga and it is therefore threatened by opencast mining activities in particular. One of the 11 known populations of F. humilis was translocated from a licensed coal mining site to three suitable receptor sites within the species? distribution range. A longterm monitoring programme was initiated to track the progress of the newly established populations. Temporal trends in population demography, size classes, and fecundity were recorded. Population numbers of size classes fluctuated annually. However, flower frequency increased over time and seedling recruitment contributed significantly to population growth. Receptor sites with similar geological conditions to the donor site had more persistent cohorts, which suggest that such sites should receive priority during the translocation of endangered edaphic specialists. This study not only confirms that a Frithia humilis population can successfully establish after a translocation, but also serves as an important baseline for future comparative purposes to gauge the long-term success of the translocation effort.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

By G. M. Evans, S. Mitra, A. V. Nguyen

As an alternative to the conventional flotation method, there has been continual research in an effort to enhance base metal ores and combustibles recovery using ultrasonics. These studies however were largely limited to the pre-treatment of ores for the removal of surface contaminants while the effect of ultrasonics on the bubble and pulp-phase interactions remained somewhat unexplored. Noting this deficiency, this study aimed to investigate the mechanistic effect of an ultrasonic field in an impeller less flotation cell specifically focusing on the bubble-particle interaction dynamics. A lab-scale flotation cell (capacity 1 litre) was designed, involving a vertically oriented ultrasonic probe (20 kHz, rated at 1.2 kW) and operated in the output power range from 1 to 20% with continuous liquid recirculation. Particle suspension was achieved by the combined action of recirculation and ultrasonic pulses. Interactions of coarse size glass ballotini particles (D32 = 314 μm) with bubbles (< 1 mm diameter) in the presence of a surfactant were studied, using high-speed imaging. Application of an ultrasonic pulse in the aqueous medium resulted in the generation of numerous microbubbles which increased with increasing input power and duration of the ultrasonic pulse time. Such periodic pulses introduced at a high level of turbulence in the pulp phase facilitated adequate bubble-particle contacts. Microbubbles played a key role in forming particle clusters which were observed to be floatable even in the absence of any carrier bubbles. When carrier bubbles were introduced, some of these particle clusters attached to the bubble surface and conveniently floated. It was noted that a favourable state of bubble-particle interaction was achievable to produce stable bubble-particles aggregates by suitably controlling the input power and period of the applied ultrasonic pulse. Keywords: Flotation, bubble-particle interactions, collision, attachment, detachment, ultrasonic pulse

Jan 1, 2020

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

Despite the media&apos;s use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996

By P. G. Henderson

Coalbrook Collieries has produced approximately 2 million tons of coal by retreat longwalling since April 1976. Strata control. support. stone intrusions. coal conveyance, and the inflow of goaf and water between the face supports have been the major operational problems experienced to date. The progressive percentage availability of the total system (moves between panels excluded) for the first three panels mined was 40 per cent. Satisfactory solutions have been evolved for these problems. and the availability in the present panel (fourth panel) has increased to approximately 60 per cent. It is envisaged that longwalling will become the most economical method of ensuring optimum heat values, greater recovery. and reduced geographic expansion. as well as safer roof conditions. at Coal brook.

Jan 1, 1980

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys&apos; experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003