Search Documents

By M. Thurston

This case study shows that for a set of lognormal data with a low coefficient of variation the semi-variogram of the logs has almost the same shape as the semi-variogram of the raw data. This means that the variogram of the logs, which is numerically more stable, can be used to krige the raw data. This technique is tested on samples from a sedimentary gold deposit and the results compared to those obtained from ordinary and simple lognormal kriging.

Jan 1, 1987

By P. J. Bartlett, H. A. D. Kirsten

A two-dimensional numerical scheme for the simulation of the plastic stress-strain properties of rock, and the various components of rock reinforcement and shotcrete, was used to rigorously determine the characteristics of tunnel support under squeezing conditions. D-shaped tunnels varying in size from 2,8 to 6,5 m in height and width were considered. The four main mining stages in the BAS block cave on Premier Mine were simulated as alternative sets of field stresses. The rock reinforcement comprised 1,8 m long fully grouted rockbolts and 6,0 m long fully grouted cable anchors at various spacings, and of various tensile and bond strengths. Various thicknesses of shotcrete and footwall support configurations were also considered. It was found that shotcrete and rock reinforcement, owing to inherent differences in stiffness, do not function in unison. As monolithic application, shotcrete has an overriding avidity for the imposed loading and destructs itself unless of extraordinary thickness. Under squeezing conditions, it accordingly supports the excavation surface while the rock reinforcement contains on-going convergence. The loads in the various support components can be determined only by simulation of the shotcrete as a stress-relieved medium to represent its broken condition in the field. The loads in the rock reinforcement vary around a tunnel and are the largest in the sidewalls. The loads increase with an increase in tunnel dimensions, the increase in load in the sidewall due to an increase in height being larger than that in the hanging- and footwalls due to an increase in width. Depending on the strength of the rock, the loads in the rock reinforcement become prohibitively large beyond a certain size of tunnel. The reinforcement of footwall rock can be omitted without adversely affecting that in other walls, provided the tensile and bond strengths of the reinforcement are not limited. The resulting footwall heave may, however, result in undermining of the reinforcement in the adjoining walls. A relative depth of anchor of 1,37 provides adequate bond strength in the larger sizes of tunnel, whereas, in smaller tunnels, anchor length is determined by the allowable convergence. The lack of fun column grouting adversely affects the efficiency of rock reinforcement to a major extent. The loads in rock reinforcement are very sensitive to the strength of the rock. Owing to a lack in refinement and calculational rigour, empirical classification systems are an inappropriate means for the design of tunnel support in squeezing conditions and, as a result, grossly unclear-estimate the support requirements.

Jan 1, 1992

By J. M. Paull, J. B. See

The rate of reaction between different carbonaceous reducing agents and silicon monoxide gas was studied by the use of a technique developed in Norway by Tuset and Raaness. Argon carrier gas was used to pass a known fixed concentration of silicon monoxide gas through an I1 cm3 sample of precalcined reducing agent at 1650°c. Silicon monoxide gas was generated by the heating of a mixture of silica and silicon carbide, and the progress of the reaction was followed by monitoring the carbon monoxide in the off-gas with an infrared spectrometer. The reactivity of silicon monoxide gas towards a number of carbonaceous reducing agents (charcoal, Iscor coke, Lurgi char, and petroleum coke) was shown to be similar to results obtained with the carbon dioxide reactivity test. The silicon monoxide reactivity test was able to indicate the extent to which fines were generated when the reducing agent was converted to silicon carbide. Of the reducing agents studied, Lurgi char appeared to be the most suitable for the production of ferrosilicon because it has a high reactivity towards silicon monoxide gas and high strength when converted to silicon carbide. So that industry could be given some indication of the suitability of certain reducing agents for the production of ferrosilicon and silicon metal, a reactivity scale similar to that of Tuset and Raaness was constructed that compares the volume of silicon monoxide gas required by a reducing agent to reach a carbon monoxide content of 10 per cent in the off-gas during the conversion of the reducing agent to silicon carbide. This scale assists in the selection of those reducing agents that require less silicon monoxide gas for conversion to silicon carbide, and that give savings in material and power costs because less silicon monoxide gas need be generated in the furnace.

Jan 1, 1979

1. New books 1979 Louisville Coal Conference proceedings. Epping (England), Bowker Publishing Co., 1980. 4 vols. $43.00. Proceedings of a joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME, held in London, 27 to 30 May, 1980, by M. J. Jones (ed.). London, Institution of Mining and Metallurgy, 1981. 350 pp. £46. Economic mineral deposits, by M. L. Jensen and A. M. Bateman. 3rd ed. New York, John Wiley, 1981. 752 pp. $22.95. E & MJ intErnational directory of mining and mineral processing operations. Epping (England), Bowker Publishing Co., 1980. 1314 pp. $67.00. Physical methods in modern chemical analysis, by T. Kuwana (ed.). New York, Academic Press, 1980. Vol. 2. 432 pp. $38.25. English translations of DIN standards. Availablefrom the SABS, Private Bag 191, Pretoria 0001. Mining international year book. London, Financial Times, 1981. 730 pp. $90.00 airmail, £37.50 surface. Analytical atomic absorption spectroscopy. Selected methods, by J. V. van Loon. New York, Academic Press, 1980. 360 pp. $35.00. 2. NIM reports Report no. 1848 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. I. The cathodic deposition of gold. (First issued 7th Jul., 1976.) Report no. 1844 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. 11. The anodic dissolution of gold. (First issued 7th Jul., 1976.) Report no. 1846 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. 111. The gold(II1)- gold(I) eaction on platinum and the disproportionation of gold(I). (First issued 7th Jul., 1976.) Report no. 1979 An electrochemical investigation of the behaviour of gold in chloride solutions. I V. Results obtained from Phase 2 of the investigation. (First issued 30th Jun., 1978.) Report no. 2093 The measurement of electrical variables in a submergedarc furnace. Steels for pipelines Since welding was first introduced as a method of joining pipelines, gas-pipeline engineers have taken the opportunity to increase gas pressures, and hence increase the efficiency and economy of transporting gases. Envitec '83 The International Trade Fair and Congress for Engineering in Environmental Protection - the ENVITEC '83 - will take place in Diisseldorf from 21st to 25th February, 1983.

Jan 1, 1981

By P. R. Jochens, D. D. Howat, R. B. Atmore

INTRODUCTION The Miller chlorination process has assumed a preeminent position in the refining of gold bullion, a position it has maintained for over half a century. In the early sixties considerable interest was aroused by the idea of producing a consistently high grade bullion at the mine smelthouses themselves. However, as the use of chlorine in industrial plants is associated with considerable hazards, oxygen was considered a natural alternative, apart from bing less expensive than chlorine. Partial refining at the mine smelthouses would considerably decrease the requirements made on Rand Refinery Limited as well as indicating the possibility of reducing final refining costs. An added factor would be the purer silver chloride obtainable, after prior removal of the base metals by oxygen injection, which would facilitate the production of high-purity silver. The free energies of formation of the oxides of the metals;- silver, copper, lead, zinc, iron and bismuth indicate that, with the exception of silver, these metals should be capable of removal as oxides by oxygen injection. Rose1 had shown that during injection of gold bullion, considerable loss of silver to the boraxsilver slag occurred and, furthermore, that copper removal was not efficient and oxide attack on the refractories was severe. Plant test work2 had confirmed the difficulty of copper removal, but had shown that zinc and lead were almost completely removed. The difficulty of copper removal by oxygen injection warranted further investigation. Also, the high decomposition pressure of silver oxide suggested that by suitable control of the slag composition it might be possible to reduce to very small proportions the silver carried into the slag as oxide. The oxidation of copper by oxygen injection and subsequent dissolution of the oxide in a slag may occur according to the following reactions; Reactions 4 and 5 were considered because of the relatively high solubility of oxygen in molten silver and silver alloys. Thermodynamic data indicate that there is little possibility of any reaction involving the formation of CuO occurring at temperatures above 1 000 °C. To ensure that the operative reactions 1 and 4 take place to the maximum extent, the following factors He significant. (a) an increase in the activity of the copper in the bullion, (b) an increase in the partial pressure of oxygen in the system, (c) an increase in the activity of the oxygen in solution in the metal, (d) a decrease in the activity of cuprous oxide in the slag. From practical considerations, the operative variable most easily susceptible to control is the composition of the slag. SOLUBILITY OF COPPER OXIDES IN BOROSILICATE SLAGS Very scanty information exists on systems containing copper oxides but the indications are that slags containing considerable amounts of boric oxide would possibly prove to be the best solvents for cuprous and cupric oxides. This is attributed to the fact that the activities of copper oxides are much lower in boric oxide slags than in slags in which silica is the main network former. The number of possible slags containing boric oxide was limited by consideration of liquidus temperature, viscosity, corrosive action on refractories, volatilization, and ultimately cost (for industrial application). Slags in the systems soda-boric oxide-silica and lime-boric oxide-silica were selected paying due attention to the above limitations. Additions of 5, 10 and 15 per cent cupric oxide were made to the finely ground, premelted slags. These mixtures were then reground and 2g quantities held in re crystallized alumina crucibles at temperatures of 1150°C and 1 250°C respectively for 30 minutes. The crucibles were removed from the furnace, rapidly cooled, cut in half longitudinally, and a thin section taken from one half was subjected to microscopic examination.

By B. J. Coetzee, P. W. Sonnendecker

The quality control of a two-stage coal washing process involves several complex components that need to be modelled accurately, to enable autonomous control of the process. The first objective is to develop a method to track the material through the washing process, while ensuring accurate washing prediction models are used. This was achieved through a digital twin model of the Grootegeluk 1 coal processing plant. The model is the amalgamation of manipulating and combining of data-sets from the plant historian, geological wash tables, and mining dispatch servers. This information is then used to control and set the processing medium densities of all 15 modules on the plant, 10 modules in the primary wash and 5 modules in the secondary wash. This controller has been successfully implemented and controlled the plant for 10 days.

Aug 2, 2022

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology's financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested into developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late eighties and early nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2003

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By A. Koursaris, Y. N. Turan

A series of experiments was caried out in a vacuum-induction furnace to investigate the solubility of nitrogen in stainless steel type 3100S. Melts were made under constant and variable partial pressures of nitrogen so that the absorption of nitrogen from the atmosphere could be examined. Additions of nitrogenized ferochromium were made to give high nitrogen contents in the steel. Nitrogen contents of up to 0,16 wt per cent were obtained under gaseous atmospheres. With additions of nitrogenized ferochromium, nitrogen contents of up to 0,525 wt per cent were obtained. Comparisons of the later value with existing data indicate that the equilibrium concentration of nitrogen was reached for the experimental conditions used.

Jan 1, 1992

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By W. Bleloch

In the process described, hydrogen is used to generate high-temperature steam and oxygen in the molten bath. Steel is decarburized to low levels to produce a pearlite-free steel suitable for deep drawing. The process makes use of the favourable thermodynamics in the reactions between steam, carbon, and iron, as well as providing high-temperature oxygen for the decarburizing reaction. The process can easily be incorporated in existing BOF (basic oxygen furnace) plant but can also be contemplated as a greenfield process.

Jan 1, 1987

A dual rate kinetic model consisting of differential equations is used to describe the kinetics of the adsorption of gold cyanide on activated carbon. The partial differential equation describing the material balance in the liquid phase is written for the special case of a fixed bed system. It is shown that an isotherm for the case of a closed system is required to yield accurate simulations of the equilibrium in a column of activated carbon. Whereas the equilibrium loading of gold cyanide is influenced by the free access of oxygen to the system, the traditional open batch stirred tank experiments, which are used to estimate parameters for the calculation of breakthrough curves for organic solutes, cannot be used here. The program solves this model at incremental heights in the column at a specific future point in time. Runge-Kutta and backwards- difference methods are used in the numerical solution. A Von Neumann method is used to show that the solution is stable. Kinetic parameters can be estimated either from batch experiments or from short column runs. In the latter method the column should not be long enough to contain the concentration wavefront for the system of interest. Results obtained from bench scale continuous column experiments were used to verify the computer model. Pure gold solutions as well as real leach liquor were used in both short column and countercurrent moving bed experiments.

Jan 1, 1987

By C. I. Ware

The phrase ?back to basics? is used to describe the fundamental principles and philosophies on which a successful mining operation is based. At Richards Bay Minerals (RBM), ?back-to-basics? (BTB) has been implemented as a continuous process to probe operational functions with a view to increase production without capital expenditure. It also ensures that the fundamentals of dredge mining are understood and adhered to. BTB is based on the principle that people drive organizations, necessitating an interactive implementation approach. At the RBM mine this entails a three-pronged approach, namely practical training, teamwork initiatives and the use of lean Six Sigma methodology. It is the latter on which this paper will focus. The lean Six Sigma methodology is successful in identifying, managing and documenting BTB projects, while team work initiatives are integral to successful project implementation. This paper describes two examples of how the Six Sigma methodology can be applied to a dredge mining operation. The first example focuses on the improvement of Mining Pond Echo (MPE) plant throughput by reducing the lost opportunity (non-production) due to tails downtime. The project was successful in increasing plant throughput by 4.5%. This was achieved by increasing the tails disposal system availability by running MPE as a four tails lines operation and focusing on causes of tails production downtime. Subsequently, the tails system at MPE is no longer the production bottleneck. Second, the Six Sigma methodology was successfully applied at Mining Pond Charlie (MPC) to increase the primary dredger throughput by 4.6% through focusing on the dredging technique and maintenance issues. This project highlighted the need for trend analyses to ensure an effective dredging technique, coupled with simple production documentation, which also ensures a focus on maintenance. Keywords: Back to basics, Six Sigma, training, teamwork, throughput improvement, tails, dredger.

Jan 1, 2007

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

[Consider the situation where we wish to estimate the value of a block of ore W from the values of n samples wt (i = 1, 2.... n). The samples can be located anywhere inside or outside W. The blocks and the samples can have any size or shape (Fig. 8.1). We define ws as the set of all the samples wi: WS = Iw1; W2; W3.. . wn and we wish to estimate the block W using the samples ws. Let xi be the value of the ith sample and µw the unknown average value of the block. We can estimate µw from the average value of all the samples. Let µw be the estimator of µw. As the samples need not be of equal size, the sample average is: µw = wi xi/~ wi. (8.1) The mean squared error made when estimating µw by µw is known as the variance of estimation of W by ws. It is the error made when giving the value of the sample set ws to the block W and is written o2E (WS to W). By definition: o2E (ws to W) = E [(µw - µw)2]. (8.2) If n = 1, this error is known as the extension variance. Since the sum of the weights given to the sample values is equal to 1,0, the estimator µw is unbiased (the question of the absence of bias is studied in more detail in Chapter 9): E [( µw - µw)1 = 0. (8.3) The error (µw - µw) has zero mean and a variance o2E = E (W8 to W). If we assume that this error is normally distributed, we can define confidence limits for µw. Let tP be the value of the standardized normal variance t such that the probability that t is less than tP is p: (t,) = .\/27T f exp (- t2/2) dt = p (8.4) The probability that µw is larger than µw + t1-P oE is p. The probability that µw is smaller than µw- t1-P oE is p. The following approximation formulae are often used to calculate 2p central confidence limits for the block value: 68% central confidence limits (p = 16%): µw - o2E, and µw + o2E. 95 % central confidence limits (p = 2,5 %): µw - 2 oE, and µw + 2 oE. Tables of the function 0 can be found in any textbook on statistics (for example, Fraser, 1958, p. 388) (see Table 7.2). [ ] The last line of Table 2.2, corresponding to f = 00, also contains the value of tP for p = 80, 90, 95 and 97,5 %.]

Jan 1, 1978

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By S. Ndlovu

To investigate the influence of orientation of crystal lattice on the bacterial leaching of pyrite crystals, single crystals of 100, 111 and110 plane orientations were used for the study. Experiments were carried out in the presence of a Thiobacillus ferrooxidans culture. The different corrosion patterns observed on the surfaces of the bioleached samples suggests a variation in cell-surface interaction from one crystal plane to the other. The surface corrosion patterns generally reflected the influence of the symmetrical arrangement of the atomic planes in the lattice on which they formed. The results indicate that the surface properties of mineral sulphides may control the evolution of corrosion patterns and consequently the initial oxidation process in acid bacterial leaching.

Jan 1, 2004

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By H. A. D. Kirsten

The paper reports on loading tests conducted on shotcrete reinforced with mesh and various types of steel fibre, and compares the results with the energy absorbing capabilities of 16 mm rebar shepherd's crooks. It is concluded that mesh-reit1forced shotcrete has sufficient energy-absorbing capabilities to contain rockbursts of significant magnitude, having greater energy absorbing capabilities, even at a thickness of 50 mm, than 16 mm rebar shepherd's crooks. Fibre-reinforced shotcrete has energy absorbing capabilities of the same order as, or better than, those of 16 mm rebar shepherd's crooks, but its performance is erratic.

Jan 1, 1995

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005