Search Documents

By U. C. Galimidi, J. M. Stewart, A. J. Van Rensburg

The effect of body movement on convective heat transfer from a man performing a block-stepping task was investigated experimentally by direct measurements of convective heat transfer. A series of experiments was conducted in which a nude man was required to stand at rest or to block step at 12 and 24 steps per minute. Wind speed, which was kept constant during each experiment, spanned the range 0,5 to 3,5 m/so Air temperature was kept constant at 43 °C in all the experiments. The results showed conclusively that the convective heat-transfer coefficient depends on the stepping rate. The effect of body motion can be regarded as being equivalent to an increase in the velocity of the free stream. The equivalent increase in air speed was found to be 0,36 and 0,77 m/s for 12 and 24 steps per minute respectively. Data from various sources, including the present study, indicate that wind speed should be increased by about 0,30,0,55, and 0,80 m/s to account for low, moderate, and vigorous body movements respectively. These findings are of direct relevance to the practical assessment of heat stress.

Jan 1, 1979

By M. I. Mabala, B. P. Watson, M. J. Kanda

A failed and stable Upper Group 2 chromitite pillar database was collected in 2007 as part of the PlatMine 1.2 pillar strength project. The database consisted of 177 pillars, of which 33 had failed. Most of the data were collected from various intermediate-depth mines near the town of Thabazimbi. Spans between rows of chain pillars were about 30 m. Pillar loads were estimated using pseudo-3D, elastic, boundary element modelling software. The pillar-load data were evaluated using a maximum likelihood regression analysis to determine strength parameters, following a similar approach to historically acceptable practice. The original formula was named the PlatMine Formula. This paper describes re-evaluations of the database, using a linear formula and several variations of the power formula. The formula providing the lowest standard deviation to the data in the database was considered the best representation of the pillars in the database. Through this rigorous process, a new formula for peak pillar strength was developed for Upper Group 2 chromitite pillars, which is unaffected by volume. The small standard deviation provided by this formula suggests a reliable relationship between strength and w/h ratio, in the w/h ratio range between 1.5 and 4.7. Accuracy, precision, and recall analysis confirmed the efficacy of this equation to the data in the database. Importantly, the new formula provided in the paper does not predict a significantly different strength to the current PlatMine formula, within the confines of the database.

Nov 27, 2024

By C. A. Green, M. A. T. Cocquerel, R. T. Gates

"Engineering studies by Selection Trust, Limited, initially in connection with the development of a copper and nickel deposit for Bamangwato Concessions, Limited, and subsequently for several other clients, have required a large number of metallurgical design calculations. The flash smelting process, developed by Outokumpu Oy in Finland, has been selected as the most suitable method for these projects and the computer programs described in this paper have been developed to facilitate the computation.The data required by the programs arc the chemical and mineralogical analyses of the concentrate, gangue and flux materials and the specification of possible fuels. The required grade of furnace matte is set as the main design parameter and the programs calculate detailed heat and material balances for the smelting process."

Jan 1, 2014

By J. Hadjigeorgiou, Y. Potvin

In a benchmarking paper published in the SAIMM Journal, Potvin and Hadjigeorgiou (2008) reviewed ground control strategies to manage large deformations in underground hard rock mines. Significant differences were identified in the design and acceptable tolerance between civil and mining engineering practice for squeezing ground conditions. Variations were also noted in ground support strategies between Australian and Canadian mines. In this paper we review progress in design methodology and ground support practice since 2008, including the availability of more effective deformation monitoring, new design tools, greater access to yielding ground support elements, and better installation practices. An improved understanding of technical and practical issues associated with squeezing conditions has led to the development of ground support guidelines for a range of squeezing ground conditions in hard rock mines.

Jul 5, 2023

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By L. M. Tavares, H. A. Petit, P. P. Cavalcanti

Iron ore pellets experience degradation during handling due low energy impacts and stresses. These impacts lead to volume or surface breakage of the pellets, creating fine particles that accumulate along the process. Some of the particles are in contact with the air and are dragged as dust into the workplace or into the atmosphere. The aerodynamic size of the particles allows them to be potentially inhaled by the workers or to be carried to nearby communities. Dust emission becomes critical at specific locations, such as transfer chutes and stockpiles. This work models the dust generation that occurs in an iron ore pellet stockyard using a methodology that combines experiments to quantify the degradation of the pellets to mathematical modelling of the dust emission mechanisms in the stockyard. First, laboratory tests were used to characterise the amount of mass and the particle size distribution of the dust generated by degradation under controlled conditions. Second, the flow over a stockpile of an iron ore pellet company was simulated with the aid of computational fluid dynamics (CFD) simulations. Third, semiempirical equations linked the data generated by simulations and laboratory tests to estimate the dust emission in the stockyard. Finally, results were validated with measured field data, obtained with a novel online measurement tool. Results suggest that the approach is able to predict dust emission with sufficient accuracy and can be used for further implementation in the management of operations and decision making in order to reduce the environmental impact of the process. Keywords: Iron ore pellets, abrasion, dust emission, mathematical modelling

Jan 1, 2020

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By R. Kuyvenhoven, A. Parbhakar-Fox, X. Prieto, J. Quevedo, L. V. Danyushevsky

This paper presents the results of a study focussed on determining the distribution of cobalt in different types of pyrite of the La Estrella IOCG deposit in Chile. In the IOCG mineral deposits, where copper is the main product, the quantification and distribution of cobalt is required to correctly define the technical and economic viability of recovering cobalt as a by-product. In the La Estrella mineral deposit, seven alteration and mineralisation events were recognised through both optical and automated electronic mineralogical analysis. Of these seven events, five different types of pyrites were identified, each with unique characteristics of the pyrite crystals. Through advanced elemental analysis of these five types of pyrites, it was determined that the concentration and distribution of cobalt within the pyrite crystal is dependent on the mineralisation event. The results indicate high cobalt concentrations in the early pyrite mineralisation events, associated with relatively fine pyrite grains, and cobalt generally occurring in a solid form in the pyrite core. The late pyrite mineralisation event exhibits the lowest concentrations of cobalt, with cobalt predominantly present along the outer periphery of the pyrite. These results are relevant from a metallurgical point of view because the preferential location of cobalt within the pyrite crystal will influence the maximum metallurgical recovery of cobalt. For this, a cobaltiferous pyrite concentrate must be formed which, according to the characteristics of pyrite, must be processed with the optimal solubilisation method. The overall objective is to ensure both good cobalt recovery and a high concentration of cobalt in the leach solution resulting from pyrite leaching. Keywords: Cobalt, pyrite, IOCG, copper, metallurgical recovery, solubilisation, Chile

Jan 1, 2020

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By P. Minkkinen, R. C. A. Minnitt

Particle size distribution analysis is important to many industries for assessing product quality, process efficiency, and compliance with contractual standards, while ensuring sample accuracy, and representativeness. Inaccurate particle size distribution results, arising from fines due to excessive handling can lead to penalties and buyer-seller disputes. A non-representative particle size distribution means samples will not accurately represent the chemical components either. Sampling blasthole cuttings poses challenges due to large material volumes, segregation, and uneven settling of particles in dense gold bearing ores. Commonly used sampling methods, such as spear or sectoral sampling, may lack representativeness. Particle size distribution analysis is crucial for evaluating sampling methods by comparing test sample representativeness against a reference standard derived from multiple particle size distribution analyses. Acceptable samples must fall within the 97.5% confidence intervals of the standard; deviations analyses lying outside these boundaries indicate a strong likelihood of segregation errors. A case study demonstrates this approach by using a 6.005 kg benchmark sample to assess two additional samples (1 kg and 5 kg), highlighting particle size distribution’s role in detecting sampling errors and refining protocols. An example of three test samples collected from reverse circulation drill cuttings compared to a standard reference sample is presented to illustrate a quality assurance/quality control procedure for reverse circulation drilling.

Oct 2, 2025

By D. F. Caicedo, I. A. Brum, L. A. Betancourt

Ferricyanide ()()*is one of the most stable cyanometallic complexes present in the gold mining effluents. This cyanocomplex is hard to degrade by natural attenuation and generates a negative impact on aquatic environments. Although free cyanide (CN-) can be obtained by acidifying the solution, the CN- is lethal for all forms of life. The oxidation of ()()* in a typical photocatalitic system was evaluated with the addition of H2O2. To verify the degradation, chemical parameters, such as free cyanide, the formation of ammonia, nitrate, and total iron were analysed at the end of the process. The degradations obtained were up to 70% in a heterogeneous photocatalysis system with TiO2, and a low rate of dissociation was observed by photolysis. The best result was achieved with the H2O2 and TiO2 photocatalytic system, and the stoichiometric concentration was about 2.5 times less than the peroxide used in the real gold mining industry, reaching 83% degradation. The photocatalytic process obtained less toxic byproducts than the original synthetic ferricyanide used as mining wastewater. Keywords: Cyanide, heterogeneous photocatalysis, titanium dioxide, UV radiation, gold wastewater

Jan 1, 2020

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

By V. Borissenkob, L. D. Ropera, M. J. Danielc

Eccentric High Pressure Centrifugal Comminution (eHPCC) is a novel comminution device that provides a single step to achieve a desired target grind size. The mechanisms within the unit mirror particle breakage that is akin to high-pressure-grinding rolls (HPGR) and high-intensity-attrition with air classification. eHPCC receives lump and can produce a product P80 such that the progeny are at or less than natural grain size of the feed. The unit operates in either closed or open-circuit. The grinding zone is dry and free of steel grinding media. This paper presents evidence of eHPCC-2 capable of selective and preferential mineral liberation. A recent test campaign on a blend of underground quartzgold- vein ore was completed. The feed to eHPCC-2 trial was SAG mill trommel oversize (low-grade pebble rejects). eHPCC-2 operated open-circuit with air-fluidisation in the rotating-grinding-chamber, classifying particles based on terminal velocity of the air-swept product particles, displaying size and mineral composition classification taking place at the same time. There is an opportunity for future industrial research targeting eHPCC as an advanced integrated comminution and classification technology. Keywords: High pressure, high intensity, compression, attrition, comminution, classification

Jan 1, 2020