Search Documents

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

NOTICES The Institution of Mining and Metallurgy The Institution is to hold a one day meeting entitled "Sampling in the mineral and metallurgical processing industries" at Imperial College, London, on 2nd July, 1973. International Conference on Air Pollution This Conference is organised by the Department of Health and the National Association for clean air. Consas 74 The Fifth Conference of Southern African Surveyorswill be held in Salisbury, Rhodesia, from 3rd to 9th February, 1974.

By M. Mbonami, R. Pretorius, J. Miller, P. Kyony, B. Nel, N. Mautsa

Challenges due to the formation of stable froth in acid leach systems is common at many copper and Ccbalt producers. Stable froth affects downstream process, critical equipment, and operational parameters. In severe cases the froth present safety and environmental risks and increased operational costs. Solids reports in the pregnant leach solution, accumulates, and clogs launders resulting in a potential costly safety and environmental risk. Solvent extraction is operationally affected by crud formation, organic solvent and extractant losses, reduced mass transfer due to the solids carried downstream. This article reviews the generally inadequate mechanical and hydraulic solutions of froth elimination employed over the years. The recent introduction of a chemically based solution able to eliminate froth problems that can potentially turn around the situation for those who adopt the technology.

Jan 1, 2023

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

By J. van Zyl Visser

The advancement in Information Technology has resulted in a change in workflow practice in our Mineral Resource Management (MRM) offices on the mines and at our corporate office. This paper discusses the AngloGold approach in defining an IT strategy for MRM, a brief overview of systems usage and benefits. AngloGold has gone through a transformation phase and has positioned itself as a world-class, low cost producer. To support this objective, an initiative has been launched to provide the MRM division with an integrated MRM technical suite of systems with support of a Management Information System. Technical systems for a tabular orebody are not freely available and hence it took AngloGold almost seven years and a significant amount of capital to develop an integrated suite of technical systems. AngloGold MRM IT adopted the typical Zachman framework (value chain) approach in the analysis process and formulated the final deliverable in terms of AngloGold’s strategy. Major benefits have been realized through the ability to change planning scenarios in a short period of time and hence be able to increase reserves and NPV. The development of MRIS, which will become the flagship in AngloGold’s portfolio of systems is in phase two and this system will allow AngloGold to publish Resources and Reserves as per SAMREC and the JORC Code at will. The availability of information at all levels of the operations has made making decisions easier and hence some specialized reports such as the Basic Mining Equation were developed from the Corporate Data warehouse and from the MRM reporting database. Decision Support Systems(DSS) such as Business Objects and Oracle Express are now being used to assist in the process. The decision to use Business Objects to replace SAS reporting as the core reporting tool has resulted in the empowerment of the user and major cost saving as far as the use of consultants to set up standard reports.

Jan 1, 2003

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By A. Basçetin

Equipment selection in mining engineering is one of the most important decisions that affects the mine design, production planning and economic parameters in open pit and underground mining. Mine planning engineers generally use their intuition and experiences in decision making. Mostly, linguistic variables (the weather is raining, soil is wet, etc.) come into question and decision-makers may not know how these variables are computed. Since the advent of the fuzzy set theory, these uncertainties are easily interpreted in the decision-making process. The development of computer technology and programming of colloquial language with expert systems have considerably reduced decision-makers? burden. This paper reviews the development of a computer programme software called EQS (EQuipment Selection) that automates equipment selection in mining engineering using fuzzy set theory. The EQS with an introduction of the concepts and theories of multiple attribute decision-making, the fuzzy set theory, and EQS applications to mining industry problems with case studies are presented

Jan 1, 2006

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

From 19 November 1996, South African companies will be able to manage the impact their activities have on the environment in terms of international standards. The establishment of a registration scheme for environmental management systems was formally announced by the South African Bureau of Standards (SABS) (19 November 1996). At a function held at the SABS head office in Pretoria, Dr Jean du Plessis, President of the SABS, announced the launch of the SABS ISO 14001 registration scheme which is based upon ISO 14001, 'the internationally recognized yardstick for environmental management'.

Jan 1, 1997

By M. J. Kahn

A new Scramble has hit the African continent. This Scramble has many drivers: the 1978 Deng Xiao Ping liberalizations in China; the 1989 collapse of the Soviet empire; the ICT revolution; the ease of global communications. The underlying dynamic is the end of the bipolar world of the Cold War and its replacement with multipolarity. According to HSBC (2011), in 2050 China will be the world?s largest economy, with India number 3 and Brazil number 7. Russia will be 15th (below its old rival, Turkey). South Africa maybe ranked 30th, yet has been invited to join the exclusive (BRIC) club. One has to ask, why? It is sad to note how low South Africa is assessed to be?currently it is around number 24 in the world; the reason for the fall is that the HSBC model includes population growth, and it is in this domain that South Africa is a loser, being constrained by the impact of HIV/AIDS on its life expectancy. The original four BRIC nations include the factory of the world (China), the garden of the world (Brazil), the gas station of the world (Russia), and the back office of the world (India). South Africa comes to the club both as jeweller of the world and as gatekeeper. China, Brazil, and Russia all have considerable expertise in mining exploration, extraction, and processing.

Jan 1, 2011

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By D. François-Bongarçon

When it comes to sampling theory, a bad sampler is a bad sampler, no matter what, and a sampler is either bad or good. It also is of critical economic importance to tell and understand the difference, especially in a metallurgical plant. In this paper, the grand principles of Sampling Theory are first recalled, then the most popular types of sample cutters for plants are critically reviewed. It is concluded that the industry has a lot of progresses to make in that direction, although improvements usually pay for themselves very quickly.

Jan 1, 2002

Book reviews Natural gas substitutes from coal and oil, by S.A. Qadar. Amsterdam, Elsevier Science Publishers, 1985. U.S.$83.25. Reviewer: U. Grimsehl High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metalurgy, 1985. 593 pp. £30. Reviewer: S.A. de Waal 2. Recent publications Uranium recovery from phosphates and phosphoric acid, by S. Huwyler. 3rd edition. Wirenlingen (Switzerland), Swiss Federal Institute of Reactor Research, EIR-Bericht (C) no. 1. Apr. 1985. 56 pp. Geological aspects of mining productivity. Canada's base metal resources, by B.W. MacKenzie. Kingston (Canada), Centre for Resource Studies, Queen's University, Technical Paper no. 6, Aug. 1985. 115 pp. $10.Taxation policies in the Canadian minerals industry, edited by M. Wojciechowski. Kingston (Canada), Centre for Resource Studies, Queen's University, 1985. Mineral policy update 1984: Policy and program changes afecting the Canadian mineral industry, by M.l. Wojciechowski and M.L. McAlister. Kingston (Canada), Centre for Resource Studies, Queen's University, 1985. $12. 3. Mintek reports Report MU7 The selective solvent extraction of pal/adium by the useof di-normal hexyl sulphide. Report M218 Modification of the design of screen boxes for carbonin-pulp and resin-in-pulp plants. Report M225 The commissioning, operation, and maintenance of an on-line corosion-monitoring station for the mining industry. Report M231The determination of selected lanthanoid elements by atomic-absorption spectroscopy using electrothermal atomization. Report M233 A computer programme for the prediction of hydrocyclone performance, parameters, and product size distributions. Report M234 The solvent extraction of base metals by mixtures of carboxylic acids and non-chelating oximes. 6 The efect of particle size and coloid stability on the wet high-intensity magnetic separation of uranium from cyanidation residues. Report M238 The beneficiation of fine coal. Report M240 The spectrophotometric determination of tin in silicates and tungsten-bearing materials. Report M242 Wear and performance of materials in pipelines for the hydraulic conveyance of fused ash. IPMI award for distinguished achievementThe International Precious Metals Institute has announced that Professor Henry C. Taube, Nobel Laureate, wil be the recipient of their 1986 Distinguished Achievement Award. Dr Taube is Professor of Chemistry at Stanford University, Palo Alto, California.

Jan 1, 1986