Search Documents

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

A new system for granting access to mineral rights is proposed in the recently released White Paper, ?A Minerals and Mining Policy for South Africa?. Official policy states that ?Government?s long-term objective is for all mineral rights to vest in the State for the benefit of and on behalf of all the people of South Africa?. In order to achieve this objective, government is presently investigating the feasibility of imposing a financial or tax-related disincentive to holding mineral rights. The paper aims to present the pros and cons and to examine the alternatives which will cause minimal disruption to the minerals industry in the period during which mineral rights are transferred to the State. South Africa is a country whose economic and political history is embedded in the development of its mineral resources and has inherited a system which cannot simply be wished away. Hasty or radical decisions will compound the problem, rather than provide a lasting and widely acceptable solution. Mineral rights ownership and its impact on access to mineral deposits are discussed. Taxation as a possible economic disincentive is also evaluated. Finally, the value of mineral resource related information as a prerequisite to mineral policy decisions and as an alternative to mineral rights taxation is emphasized.

Jan 1, 1999

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publicatiol1 of technical notes taking up to three pages (maximum 3000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute asa body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

By R. B. Khumalo, F. K. Mulenga

Sampling in a continuous flotation plant is always a challenge as these plants are meant for production and not research work. The continuous flotation operation used in this work produced three sets of data: the first was based on overall plant performance, done by sampling the feed, concentrate, and tails; the second was based on the roughers row cell-by-cell; the third set of results came from the cleaners/recleaners row cell-by-cell. The highest recovery results in all sets of data obtained lie in the particle size ranges of 40 μm and 100 μm, which is in agreement with results by other researchers in the same field. King’s theoretical (model) recovery proved to be able to fit the experimental data but there is still room for improvement as the sum of squared error ranged between 400– 1200. Data obtained in continuous flotation operation could be used with batch flotation test-work to characterize scale-up of flotation cells.

Jan 1, 2023

By G. Heymann, T. Grobler

Many tailings storage facilities in the Rustenburg region of South Africa’s North-West Province are founded on reworked residual norite derived from the weathering of the Bushveld Igneous Complex. With the implementation of the Global Industry Standard on Tailings Management, increased emphasis is placed on robust material characterisation, but laboratory testing is challenging. The results of Oedometer and undrained triaxial shear testing support a nonlinear failure envelope for effective stresses below the yield stress, transitioning to linear behaviour at higher stresses.

Apr 8, 2026

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for the expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated ?risk? via the discount rate and other assumption contingencies around gold price expectations, operating parameters etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Carbon Modelling Technology and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. 44 percent chance of project finance loss.

Jan 1, 2012

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012