Search Documents

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004

By Roger A. Blais, Michel David

"Matheron's geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By K. Sasaki, S. Kuroiwa, H. Miki, Y. Aoki, T. Hirajima, Y. Orii, G. P. W. Suyantara

Selective flotation to separate copper minerals from, for example, Mo- and/or As-bearing minerals is a continuing problem because the selectivity of current systems is imperfect. Selective Cu-As flotation is currently difficult, and the most common Cu-Mo selective flotation method uses NaHS; this must be done in an enclosed system because, under acidic conditions, this method produces hydrogen sulfide. In this paper, some novel alternative flotation processes that use redox reactions are discussed; these methods have a much lower environmental impact. Oxidation and reduction reactions can be used to make copper minerals more hydrophilic and Mo-bearing minerals more hydrophobic. X-ray photoelectron spectroscopy (XPS) analyses indicated that the copper minerals became hydrophilic because hydrophilic iron precipitated and several hydroxides covered the copper minerals’ surfaces, whereas the molybdenum minerals remained hydrophobic because their sulfide surfaces were not covered. Flotation experiments on these minerals after redox treatments indicated that excellent separation of Cu-minerals from Mo-minerals can be achieved. Possible mechanisms for this separation were investigated using detailed surface analyses and thermodynamic calculations. The additives used to initiate the redox reactions are easy to handle and make these new flotation procedures better than current processes because the new methods do not emit effluent gas and because they are commercially viable. Keywords: Flotation; chalcopyrite; molybdenite; oxidation; reduction

Jan 1, 2020

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical of these processes is that the amount of slag is quite high. The role of slag for the process is thus essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2 based with minor contents of CaO and CrOx. Slags in the FeMn process are principally similar, originating from silicate minerals but can have quite large composition range depending on the manganese ore and its gangue minerals. Characteristic of the FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOx in slag are not only divalent oxides but also contain some higher valent of Cr3+and Mn3+, respectively. In FeMn production conditions the slag consists mainly of Mn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexist in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. The thermodynamics of slags in ferroalloys, production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties

Jan 1, 2004

By Y. H. Hatzor

ABSTRACT: A fully dynamic, two dimensional, stability analysis of a highly discontinuous rock slope is demonstrated in this paper. The studied rock slope is the upper terrace of King Herod’s Palace in Masada, situated on the western margins of the seismically active Dead Sea Rift. The dynamic deformation of the slope is calculated using a fully dynamic version of DDA in which time dependent acceleration is used as input. The analytically determined failure modes of critical keyblocks in the jointed rock slope are clearly predicted by DDA at the end of the dynamic calculation. It is found however that for realistic displacement estimates some amount of energy dissipation must be introduced into the otherwise fully elastic, un-damped, DDA formulation. Comparison of predicted damage with actual slope performance over historic time span window of 2000 years allows us to conclude that introduction of 2% kinetic damping should suffice for realistic damage predictions. This conclusion is in agreement with recent results of Tsesarsky, Hatzor and Sitar (2002) who compared displacements of a single block on an inclined plane subjected to dynamic loading obtained by DDA and by shaking table experiments. Using dynamic DDA it is shown that introduction of a simple rock bolting pattern completely stabilizes the slope. RÉSUMÉ : On présente dans cet article une analyse bidimensionnelle complète de la stabilité d’une pente rocheuse très fracturée. La pente rocheuse étudiée est la terrasse supérieure du Palais du roi Hérode à Massada, située sur la rive Ouest du Rift sismiquement actif de la Mer Morte. La pente est constituée de blocs de dolomite raide présentant une stratification sub-horizontale et des joints sub-verticaux. La déformation dynamique de la pente est calculée en utilisant une version entièrement dynamique de l’Analyse de Déformation Discontinue (DDA) où l’accélération dépendant du temps est utilisée comme donnée. Les modes de rupture déterminés analytiquement des blocs clés dans la pente rocheuse fracturée sont clairement prévus par l’approche DDA à la fin du calcul dynamique. On trouve cependant, que pour obtenir des estimations réalistes du déplacement, il faut introduire un facteur de dissipation énergétique sans lequel la formulation DDA serait totalement élastique et sans amortissement. En comparant l’endommagement prévu avec les caractéristiques de la pente sur une période historique de 2000 ans, nous pouvons conclure que l’introduction d’un amortissement cinématique de 2% suffit pour obtenir de prévisions réalistes. Cette conclusion est conforme aux résultats récents de Tsesarsky, Hatzor and Sitar (2002) qui ont comparé les déplacements d’un bloc isolé sur un plan incliné sous chargement dynamique obtenus avec l’analyse DDA et à partir d’essais sur table vibrante. ZUSAMMENFASSUNG: En utilisant une modélisation DDA dynamique on montre que l’introduction d’un système simple de boulonnage stabilise la pente.In dieser Veroeffentlichung wird eine vollstaendig dynamische, zweidimensionale Stabilitaetsanalyse eines hoechst diskontinuierlichen Steinhangs dargestellt. Der untersuchte Hang ist die obere Terrasse des Herodespalastes in Massada, welche in den westlichen Randgebieten des seismisch aktiven Toten Meer Grabens liegt.Die dynamische Deformation des Berghangs wird mit Hilfe einer vollstaendig dynamischen DDA-Version berechnet, in welcher als Input die zeitabhaengige Beschleunigung eingegeben wird. Die analytisch bestimmten Versagensarten kritischer Schluesselbloecke in diesem zerkluefteten Steinhang werden durch Anwendung von DDA am Ende der dynamischen Berechnung klar vorausgesagt. Es zeigt sich jedoch, dass fuer realistische Dislozierungs-Abschaetzungen ein gewisses Mass an Energieverlust in der sonst vollstaendig elastischen, ungedaempften DDA-Fassung einbezogen werden muss. Der Vergleich des vorhergesagten Schadens mit dem aktuellen Verhalten des Berghangs waehrend einer historischen Zeitspanne von 2000 Jahren erlaubt uns zu schliessen, dass ein Zusatz von 2% kinetischer Daempfung fuer eine realistische Vorhersage des Schadens ausreichen sollte. Diese Schlussfolgerung steht im Einvernehmen mit neuen Ergebnissen von Tsesarsky, Hatzor und Sitar (2002), welche die Dislozierung eines einzelnen Blocks auf geneigter Ebene unter dynamischer Belastung – unter Anwendung von DDA und “shaking table”-Versuchen – verglichen. Mit Hilfe der dynamischen DDA wird gezeigt, dass der Steinhang durch Anwendung einer einfachen Steinschraubenstruktur vollkommen stabilisiert werden kann.

Jan 1, 2003

Instability in rockpasses at deep levels often initiates as a result of stress induced fracturing of the rock on the walls of the pass. This may then progress to a stage at which the geological structure of the rock mass becomes dominant and permits large joint-defined blocks and slabs to become unstable. In this paper, a technique is described in which jointing parameters and their variabilities?orientations, spacings and lengths?are taken into account in estimating the extent of failure that may develop around a typical unsupported deep level gold mine rockpass. The results of this prediction are compared with the results obtained from a review of pass performance in the gold mining industry.

Jan 1, 2005

INFACON conjures up many things for many people. For the fortunate few who have been actively involved with this event since its inception, it brings back memories of far places, stimulating debates and above all, the people who have over the years contributed to the outstanding success of the Congress and who have added to the wealth of knowledge on all aspects of ferroalloys. The International Ferroalloy Congress (INFACON) has been held every three years since 1974. INFACON X will be held in Cape Town in February 2004. Simple arithmetic shows that next year?s Congress should in fact be INFACON XI. Thus, one Congress was skipped. INFACON 74, as the name implies, was held in 1974, in Johannesburg, South Africa. The event was sponsored by the Ferro Alloy Producers? Association of South Africa (FAPA), the National Institute for Metallurgy (NIM - Mintek as it is known today) and the South African Institute of Mining and Metallurgy (SAIMM). You will see some of the same sponsors involved in INFACON X. Dr. Robbie Robinson, renowned academic and past president of the SAIMM, was the Chairman of the Organising Committee. The editor was Dr. Helen Glen. Anyone fortunate enough to possess a copy of the proceedings of this first Congress will agree that from a literary and technical perspective, it is still the benchmark for subsequent events. A unique feature of INFACON 74 was the use of rapporteurs (my first duty) to ensure that the discussions following the presentations were recorded (in direct speech) as accurately as possible. This involved time-consuming correspondence (can you imagine life before e-mail?) to all parts of the world between the author and the person posing the question, with the rapporteurs acting as go-betweens. It is understandable that the much-awaited proceedings only saw the light in 1975. The names recorded in the proceedings as the members of all six committees read like the who?s-who of the South African ferroalloy industry at the time: Dr. Peter Jochens, Mr. Harvey Reid, Mr. Piet Streicher, Prof David Howat, Mr. Sigurd Selmer-Olsen - to name but a few. The Congress was held in the new, very fashionable and upmarket Carlton Hotel in the CBD. In the Foreword of the proceedings, Dr. Robinson provides an insight into the event. Three hundred and thirty six delegates from twenty two countries attended the Congress, which was opened by the Honourable P.G.J. Koornhof, Minister of Mines. Again, the opening address makes fascinating reading. During the Congress an ad hoc committee was convened as the first International Committee on the Organisation of Ferroalloys Congresses, with representation from the main ferroalloy associations of the world. The following decisions were recorded: ? The Congress would be continued at three-yearly intervals under the name of INFACON ? Every third Congress would be held in South Africa ? NIM (Mintek) would provide the permanent secretariat. Six technical sessions were held, each preceded by a plenary address with a closing address by the session chairman. In all, thirty technical papers were presented. Prior to the closing address, a panel discussion on factors affecting the future of the ferrochromium industry provided stimulating debate in the form of a question-and-answer session. The hosting country for the next INFACON would be announced. Eventually, word got round that the next INFACON would be held in Japan. However, due to unforeseen circumstances, the event was cancelled ? thus no INFACON 77. INFACON 80 was subsequently held in Lausanne, Switzerland from 12th to 16th October 1980. The event was organised by IFPEO, Institut des Producteurs de Ferro-Alliages d?Europe Occidentale. The Congress was officially opened by the President of IPFEO, Mr. R. Björklund, who was also President of the Organising Committee. The technical sessions were held in the Palais de Beaulieu. The Congress was well attended by 400 participants from 28 countries as well as 100 accompanying ladies. A total of four plenary addresses and 18 technical papers were presented. As with the first event, an international panel discussion (questions and answers) preceded the closing address. In his closing address, Dr. Louw Alberts, Chairman of the International Committee on Ferroalloys and President of NIM, presented an insight into the factors affecting growth in the industry and where growth was likely to take place. Twelve exhibitors had stands at the Congress. Attendees could choose from four post-event tours to Belguim/France (SADACEM/Compagnie Universelle d?Acetylene et d?Electro-Metallurgie), France (CUAEM), Finland (Outokumpu Oy) and Norway (Elkem Fiskaa plant).

Jan 1, 2004

The rising tide of environmentalism has adversely affected many mineral producers, but it has also provided them with a number of opportunities for mineral applications. These markets are as diverse as water treatment, waste disposal, and flue-gas desulphurization. Whilst legislation is forcing up the industry&apos;s environmental standards, the advent of environmental management provides an opportunity for producers to display its &apos;green&apos; credentials. The picture painted of the extractive industry by environmentalists is undeservedly black, because the more efficient a producer is, the more effectively that producer conserves the very resources he exploits. The 1993 IM Forum examined these issues and how they affect the mineral producer, and this publication comprises the papers presented at that meeting.

Jan 1, 1995

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l&apos;affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d&apos;affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d&apos;affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By A. T. Visser

"SynopsisAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads was conducted in South Africa. This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential.These principles have been implemented worldwide, and it is useful to review the lessons learned. The objectives of this paper are to present a critical review of the status of mine haul road design and management, and the impact that these principles have made on operations, particularly the cost-effectiveness. The paper briefly reviews the principles of the haul road design and management and the extent to which they are applicable. Case studies of a number of implementations are presented to demonstrate that the principles are sound and have been applied effectively. For example, at an international operation the transport cost of coal was 40% more expensive than anticipated in the feasibility stage, and this made the mining operation uneconomic. Correction of this problem resulted in a viable enterprise. Although designed for opencast operations, the principles are equally valid for underground operations, and initial development work will be discussed.The main conclusions are that the research approach is valid and its effectiveness has been demonstrated in a number of applications. The anticipated financial benefit has been derived, and has made the mining operations that used the principles more effective. Of major importance is the application of opencast haul road design principles to the future thrust of using driverless vehicles in opencast and underground mining, where the road quality is not negotiable as there is no driver that can avoid obstacles or severe road deterioration.IntroductionAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads in South Africa (Thompson and Visser, 1996a, 1996b, 1998, 1999, 2000a). This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential."

Jan 1, 2015

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

A new method, localized uniform conditioning (LUC), was proposed in 2006 for modelling grades of small blocks of ore when data spacing is too broad for their accurate modelling by the linear regression based techniques, such as kriging (Abzalov, 2006). It represents a modified uniform conditioning (UC) technique that calculates the grade distribution functions for the large panels. LUC uses partitioning of the panels onto the small blocks and then ranks them in increasing order of grade. Based on the block ranks, a single grade value can be deduced for each block from the UC model of the gradetonnage relationships of the corresponding panel. After being first presented in 2006, the LUC method has been implemented in ISATIS© (commercial software) and became one of the common approaches for grade estimation when data spacing is broad in comparison with the estimated block size. Several years of study on the LUC method and its application to different geological environments, have allowed identification of the strengths and weaknesses of the method, which are as follows: ? The method produces accurate grade-tonnage functions, which are in a good accordance with a volume-variance relationship principles ? An initial ranking of the selective mining unit (SMU) blocks can be made by direct kriging from the sparse data grid. Therefore, the LUC method can be particularly useful at the early stages of exploration and mining project evaluations when sparsely distributed data is often the only available information ? Accuracy of the local estimation depends on the SMU ranking techniques. When ranking performed by direct kriging of the SMU blocks their spatial distribution is approximate. When the variogram of the studied variable is characterized by a large nugget effect, the block ranks produced by kriging can significantly differ from their ?true? distribution ? Block ranking can be improved using auxiliary data, either geophysical or geochemical. This allows use of the LUC method for integrating different data sets. In particular, LUC can be used for grade control in open pits by integrating resource definition data (e.g. drill-hole assays) and blast-hole assays. The latter are used for the block ranking.

Jan 1, 2014

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By L. van Dyk

The project was aimed at evaluating the double-header trains implemented at Great Noligwa mine, looking at the changes from the old conventional trains to the new trains, and identifying possible improvements to obtain an even better and more productive tramming system. The methods used to evaluate the double-header trains at the mine included personal observations, time studies, personal interviews, technical research, safety analysis, cost analysis, production analysis, breakdown analysis, break test analysis, comparisons and working closely with engineering department and manufacturers. Issues that were evaluated are the improvements in safety, cost reductions, tramming congestion reductions, better efficiencies, labour optimization, enhanced driver safety and maintenance. Shortcomings of the double-header trains were identified and recommendations made to improve on the shortcomings. Findings of the evaluation study indicated the following: ?Drastic improvement on safety ?Extreme cost reductions ?Reduction in tramming congestions and bottlenecks ?Better tramming efficiencies ?Optimized labour placement ?Enhanced driver safety ?More effective maintenance. Although there is room for improvements, the double-header trains were implemented with great success at Great Noligwa mine. It is currently the preferred tramming methodology at Great Noligwa mine, and is also implemented at other Anglo Gold Ashanti?South Africa shafts. This tramming system has huge potential for growth, not only in Anglo Gold Ashanti, but in all other older mines that experience major tramming problems.

Jan 1, 2008