Search Documents

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By C. L. Workman-Davies

Noise is a form of pollution arising mainly from the activities of man. One such activity is mining, in which man, as in many of his other activities, uses machinery of various kinds to achieve safe, healthy, and economic production. Trackless mining makes use of an advanced state of technology over that required In traditional mining methods. One of the advantages of the former, as distinct from any disadvantages it may have, is a reduction in noise levels, the number of people exposed to noise, and the duration of their exposure to noise. This paper briefly examines why noise is a problem and what various countries are doing about it in terms of standards, codes of practice, and regulations. It also investigates the extent to which noise is a problem in mining and how trackless mining alleviates this problem. The question is then posed as to whether South Africa is not setting too high a standard at this stage of its national development by comparison with what is being done by other, more-advanced countries.

Jan 1, 1989

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By M. Mokgohloa, T. R. Stacey

Boring of tunnels and shafts in hard rock under high stress conditions is becoming more common as mines and tunnels are developed at greater depths. Under the high stress conditions, fracturing of the often-brittle rock occurs in the walls, backs, and ahead of advancing faces of excavations. Fracturing can have a significant impact on boring activities: sidewall spalling, which affects machine gripper capacity, and fractures can also develop in the rock ahead of the face, leading to blocky rock conditions, which may have a significant effect on machine excavation. Fracturing may develop dynamically, leading to rock bursts manifesting in the form of strain bursts, which can be hazardous and destructive. In brittle rock, fracturing is commonly extensional in nature. The focus of this paper is on fracturing in the face of the excavation. Examples of such fracturing behaviour are described briefly in the paper. Numerical analyses were carried out to predict the initiation of extension fractures and their orientations ahead of excavation surfaces, and the resulting formation of rock slabs/plates, and the stability of these plates. The results should be beneficial for the evaluation of the conditions prior to, and during boring operations.

Nov 27, 2024

By J. Gómez-Hernández, P. K. Kaiser

Abstract The process of stress-induced fracturing around underground excavations in brittle rock is associated with dilation or volume increase of the failed, fractured rock. Different attempts to account analytically for this dilation have been made within the framework of plasticity theory. This theory has been developed mostly for metals, strain-hardening materials or soils, but brittle failure of rock-like materials is characterized by strain-softening behaviour and the volume change is dominated by geometric factors, which may violate stability principles of plasticity. In this work a semi-empirical Rock Mass Bulking Model (RMBM) was developed, using as starting concepts: dilation angle, plastic strain rates, effective deformation modulus, effective Poisson's ratio, Griffith locus, and the definition of a bulking factor BF introduced by Kaiser et al. (1996). The model was calibrated in order to obtain bulking factors that are consistent with experimental data and case studies of measured bulking around underground excavations. Résumé La fracturation provoquée par le stress autour des excavations souterraines dans le minéral friable est associée à la dilatation ou à l’augmentation du volume de la roche en rupture. Dans le cadre de la théorie de la plasticité, différents essais ont été faits dans le but de trouver une justification analytique pour cette dilatation. Cette théorie a d’abord été élaborée pour les métaux, les matériaux ou les sols d’écrouissage, mais la rupture fragile de matériaux d’aspect rocheux est caractérisée par un comportement d’amollissement et le changement de volume est dominé par des facteurs géométriques, ce qui pourrait ne pas être conforme aux principes de stabilité de la plasticité. Dans le présent ouvrage, un Modèle semi-empirique de masse rocheuse a été élaboré, dont les concepts initiaux sont les suivants : angle de dilatation, vitesse de fluage plastique, module effectif de déformation, coefficient effectif de Poisson, locus de Griffith, et la définition d’un facteur de foisonnement FF apportée par Kaiser et al. (1996). Le modèle a été calibré afin d’obtenir des facteurs de foisonnement qui soient conformes aux données expérimentales et aux études de cas sur le foisonnement mesuré autour des excavations souterraines. Kurzfassung Der Prozess von Brüchen in unterirdischen Abgrabungen in sprödem Gestein ist mit der Ausweitung oder der Volumenzunahme des gebrochenen Gesteins verbunden. Verschiedene Versuche im Rahmen der Verformbarkeitstheorie haben versucht, diese Ausweitung analytisch festzustellen. Die Verformbarkeitstheorie wurde hauptsächlich für Metalle, kalthärtende Werkstoffe oder Böden entwickelt, da sprödes Versagen von Gestein ähnlichen Werkstoffen von kaltenhärtendem Materialverhalten gekennzeichtnet ist, und die Volumenveränderung von geometrischen Faktoren beherrscht wird, die die Stabilitätsprinzipien der Plastizität übertreten. In dieser Arbeit wurde ein halbempirisches Rock Mass Bulking Model (RMBM) (Modell für das Aufgehen der Gesteinsmasse), entwickelt, für das die folgenden Anfangsprinzipien benutzt wurden: Ausweitungswinkel, plastische Fliessensätze, wirksames Verformungsmodul, leistungsfähiges Poissons Verhältnis, die Griffith Ortskurve und die Bestimmung eines Aufgehensfaktor BF1 der von Kaiser et al. (1996) eingefürt wurde. Das Modell wurde so kalibriert, dass es die Aufgehenfaktoren erzielte, die mit den Vesuchsangaben und den Fallstudien von Aufgehensmessungen in unterirdischen Abgrabungen übereinstimmen.

Jan 1, 2003

By N. Kernahan, T. Zaniewski

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Sep 1, 2001

By Xu H.

In recent years, the mineral applications dealing with more complex data in distributed environment have grown rapidly. Many mineral and mining organizations have to organize internally and globally distributed manufacturing and experiment sites, which share the roles of databases and other multi-services like software programs. Thus, there are commercial and technical pressures pushing the mineral software vendors to move their current service toward Web service. XML has gained wide acceptance for representing, storing and transferring structured data and documents of many kinds, especially in scientific communities. However, so far there is no such a Markup Language in mineral industry. A XML-based uniform encoding, which is called MineML(Mineral Markup Language), is proposed and developed in this project. The framework of the MineML specification is created. MineML will play the role as shared protocols within mineral domain for archiving, transferring the multi-nature data between the software packages on the desktop over the Internet and sharing the services between users at different sites. Inspired by MLA’s (Mineral Liberation Analyser, JKMRC, University of Queensland, Australia) Mineralogical Data Presentation Program, a proof-of-concept prototype of Web Service is developed here to validate and demonstrate the MineML specification. Certain strategies, specific technologies and tools are adopted to create such an environment. To accomplish that, a set of experimental MineML documents including correlated XML, XSD (schemas) and XSL(stylesheets) documents have been elaborated for archiving, presenting and transferring the mineralogical data information, with the persistence on flexibility and extensibility for generic mineral and mining data handling.

Jan 1, 2003

By Q. C. Reynolds

Keywords: Pyrometallurgy, plant, photography, GIS, satellite images, Google Earth Google Earth is a piece of software able to display an interactive three-dimensional map of the world, combining aerial and satellite photography with maps, terrain, and user-generated geographical information systems (GIS). Many structural features of the planet, both natural and man-made, are of great interest to the mining and metallurgy field, and in this paper a study is made of the current state of the art of data accessible by Google Earth.

Jan 1, 2006

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

"Chairman: Mr W. S. GALLAGHERRapporteur: Professor A. M. STARFIELDPapers:Long-term mine production scheduling by G. C. S. BurneAn application of linear programming to investment analysis by A. ErlandssonOptimizing medium-term operational plans for a group of copper mines by M. Splaine, D. C. Atkinson, W. Davison and L. SmithThe simulation of underground stoping and transport operations in gold mining by F. H. Touwen and N. C. JoughinProduction planning is a subject that lies at the interface between the computing centre and mine management. Discus¬sion during this session was thus largely concerned, directly or indirectly, with communication between computing and mining personnel, and as such was relevant to the symposium as a whole.Mr A. Weiss set the tone of this discussion by referring to `user-orientated systems'. He congratulated Mr Burne in this regard, pointing out that his long-term production scheduling program, as a computer system, was similar in approach to the manual system it replaced, and was therefore easily understood by planning engineers. He asked whether the schedule engineer had his 'hands on' the system, to which Mr Burne replied that the engineer did in fact spend several days running alternative schemes through the computer. Mr Weiss commented on the advantage of having terminals on site for this sort of engineer-computer interaction. He also commented on the flexibility of Mr Burne's approach to scheduling and how preferable this was to a one-step optimization package. This was brought home by a question from Mr H. D. Small: Mr Burne's program sometimes found it necessary to temporarily halt an advancing face, and he asked whether the logic of the program could be altered to avoid this (e.g. by suitably slowing down the rate of face advance). Mr Burne replied that it was in fact easier for the planning engineer to sort this problem out manually. The way in which the computer results were presented made it particularly simple for the production engineer to see how to avoid or remedy a stopped face.On the technical side, both Mr Weiss and Mr H. M. Wells questioned Mr Burne on the handling of grade control by his program. From answers by Mr Burne and his colleague Mr K. H. Thomson it emerged that a spot-check on grade every now and then was all that was necessary at Mufulira, and that the idea of actual grade control was more a question of short-term than of long-term planning."

Jan 1, 2014

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By Lutz Markworth, Wolfram Jaspers, Johannes Kottmann

PNEUFLOT® technology has been applied for the past 20 years in coal, ore and other minerals processing plants. During the last two years this technology has achieved a breakthrough with some 42 units being sold signifying a rising trend. »Humboldt Wedag Coal & Minerals Technology« has performed extensive research and development work over the last five years. The results of which were used to design a new fourth generation aerator. Humboldt Wedag, through its association with EKOF, can offer a holistic solution encompassing both flotation equipment and reagents. It is the only company in the world able to offer such a package. The association with EKOF strengthens the Humboldt Wedag product offering, especially as the company in-troduced pneumatic flotation cells to the South African market in the form of the PNEUFLOT®. Before starting pilot scale test work, a mineralogical analysis has to be carried out to determine the mineral com-position as well as the liberation grade. HW-CMT works together with independent institutes. Different reagent regimes can be tested in laboratory scale. Pilot machines, each packed in a 20? container, are available to carry out extensive test work at customers? processing plants. A group of engineers from HW-CMT is involved in the pilot test work. The flexible pilot machines are designed to cater for coal, ores and other minerals. The small feed rates of 7 ? 12 m³/h only means the pilot machines do not disturb the operation of process plants. Batch tests have to be carried out to determine the numbers of PNEU-FLOT® stages. New applications in iron ore, copper ore, platinum group minerals, rock phosphate and potash were suc-cessfully tested in the last three years. In applications where the feed material is very fine, PNEUFLOT® technology is able to achieve high recoveries with particle sizes where conventional technology failed.

Jan 1, 2007

By J. D. Steenkamp, G. E. Williams

Keywords: Ilmenite, titania slag, pig iron, rutile, zircon Located on the eastern shores of South Africa, 180 km north of Durban, Richards Bay Minerals (RBM) produces approximately 2.0 million metric tonnes of product annually making RBM a leading producer of titania slag, high purity pig iron, rutile and zircon. Heavy minerals are extracted from the nearby dunes by dredging and concentration on a floating gravity separation plant, followed by separation of the ilmenite, rutile and zircon at the mineral separation plant located at the smelter site. The ilmenite is processed through an oxidizing roast followed by magnetic separation and is then partially reduced to an 85 per cent TiO2 slag in one of four six-in-line a.c. electric arc furnaces. The slag is milled and then classified into two product sizes suitable as a raw material for both the sulphate and chloride pigment processes. The high quality iron produced during the reduction process is further processed to produce various grades of low-manganese iron. Around 95 per cent of the products are exported, yielding a world market share of about 25 per cent of titania slag, rutile, high quality pig iron, and zircon.

Jan 1, 2006

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007