Search Documents

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

Discussion H. J. S. Kriek*: During 1956 Iscor became interested in the acid smelting in a blast furnace of siliceous ores containing 15 per cent silica. This interest was as a result of the successful acid smelting in Germany at a CaO/SiO2-ratio of between 0.4 and 0.8. Acid smelting can become an economic proposition due to a reduction in slag volume accompanied by a lowering of the coke rate. Paschke and Hannel1 found that a free flowing slag (i.e. viscosities of less than two poise) would not be obtained at C/S-ratios lower than 0.82 and that the addition of 3 to 4 per cent alkalies became necessary. In titanium bearing slags it was established that maximum fluidity is obtained with 10 per cent TiO2. Acid smelting resulted in increased sulphur pickup with decreasing O/S-ratio and desulphurization with soda-ash outside the blast furnace was necessary. At Iscor Mr B. B. Segal established that, for slags with (CaO+MgO)/SiO2-ratios of 0.5, 0.6 and 0.7, the addition of alkalies and TiO2 resulted in a substantial decrease in melting point and also of viscosity. At a (CaO+ MgO)/ ratio of 0.53 the addition of 10 per cent TiO2 is as effective as the addition of 3.75 per cent alkalies. This means that a blast furnace can be run without the addition of alkalies and consequently the detrimental effect of alkalies on the lining can be avoided; also that fluid slags with 5 to 15 per cent MgO and 8 to 10 per cent Al203 can be obtained with 10 per cent TiO present. (CaO+ MgO)/SiO2-ratios smaller than 0.5 the addition of titania resulted in a decrease in melting point and also in an increase in viscosity. In ceramic crucibles the slag did not become more viscous with time but thickened appreciably when held in graphite crucibles. No titanium carbonitride could be detected and only Ti20a was found. Prof Howat also did not obtain the TiC-TiN solid solution and therefore it appears that the thickening of the slag is not solely due to the formation of the titanium carbonitrides. This is in agreement with the work of Michailov and Belyakova2 who found that TiO2 decreased the viscosity of acid slags and increased the viscosity of basic slags; that titanium sesquioxide (Ti203) and titanium monoxide (TiO) increased the viscosity of both acid and basic slags and that titanium carbide, which is found in larger amounts in basic slags than in acid slags, considerably increases the viscosity of both acid and basic slags. Patzak et al3 describes the following oxygen deficient titanias, viz Ti2O, TiO, Ti203, Ti3O5, Ti4O7, Ti5O9, Ti6O11- Ti10O9,Ti7O13,Ti8O15 and Ti9O17. Until about 1959 a fair amount of data was available on the viscosity of normal slags to which titania was added2, 4, 5, 6, 7, 8, 9. At Iscor an electromagnetic viscometer based on the viscometer developed by Bockris10 was built. Progress was very slow as our main attention was centred around problems associated with the operation of the Rotor process. During 1962 and 1963 two papers containing fundamental work on the viscosities of slags in the systems CaO-SiO2-TiO211 and CaO-SiO2-TiO2 at 0 per cent A1203, 10 per cent Al203 and 20 per cent Al20312 appeared. The work of Ross and Ohno obviated the necessity of any further work by Iscor on the viscosity of blast furnace slags containing titania. Ross gave the following optimum compositions for blast furnace slags containing titania. Titania % Lime % Silica % Lime/Silica-ratio 20 30-42 38-50 0.6-1.10 30 27-36 34-43 0.63-1.06 40 24-32 28-36 0.66-1.14 The optimum temperature is 1,500°C because at this temperature the largest workable composition range exists. Higher temperatures result in narrower optimum composition ranges and in increased rates of thickening. The factors affecting the rate of thickening were also investigated by Ross and Ohno, as the main problem with slags containing titania is not finding compositions which are fluid at operating temperatures but the thickening due to a lack of oxygen. With these slags when there is insufficient oxygen to co-ordinate each silicon atom with its own individual shell of four oxygen ions, some sharing of oxygen ions must occur, resulting in the formation of large silicate ions and a rise in viscosity. The formation of oxygen deficient titania can be prevented as long as iron oxide or manganese oxide remain in the liquid slag. Iwase13 and also Viens, Camp bell and Rogers14 obtained in the experimental smelting of ilmenite ores fluid slags with more than 3 to 5 per cent manganese oxide and ferrous oxide in the slags. It appears that titaniferous ores can be smelted in blast furnaces under the following conditions: (1) Acid slag operation, i.e. at C/S-ratios from O.6-1.0. (2) Dolomite can be used as a flux as MgO is a network modifier. (3) The Al2O3-content must be less than 15 per cent as alumina promotes thickening of the slag and decreases the optimum composition range. (4) The hearth temperature must not exceed 1,500°C. According to Ross a definite amount of energy is required for each ton of iron produced and in order to increase production an increase in heat

Jan 6, 1969

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

The following comment has been received from Mr A. D. Osche* on the above paper, which was published in the Journal in October 1977 (vol. 78, no. 3, pp. 51-62). Obituary: T. K. Prentice The Institute records with deep regret the death on 30th January of its senior surviving Past President, Mr Thomas Kennedy Prentice, at the age of 83. Book reviews R. A. Rich, H. D. Holland, and U. Petersen. Hydrothermal uranium deposits. (Developments in Economic Geology, vol. 6). Amsterdam, Elsevier Scientific Publishing Co., 264 pp. with 77 illustrations and diagrams, 30 tables. U.S. $34,75. M. David. Geostatistical ore reserve estimation. Amsterdam, Elsevier Publishing Company, 1977. 364 pp. World mineral industry The Australasian Institute of Mining and Metallurgy is celebrating its sesquicentenary in 1979. A conference will be held in Perth from 13th to 18th August, 1979, as part of the celebrations, the theme being 'Australia's Role in the World Mineral Industry'. Engineering teaching staff UNESCO has extended its technical assistance to the Venezuelan government in the training of engineers to suit the rapidly developing economy of the country. UNESCO vacancy Vacancy for a post of expert under the UNDP. (1) Title of post: Expert in metallurgical engineering. (2) Duty station: Instituto Universitario Politecnico of Ciudad Guyana (Venezuela). Shell Design Awards The annual Shell Design Awards, organized by the Design Institute and sponsored by Shell South Africa (Pty) Ltd, focus attention on achievements in South African design.

Jan 1, 1978

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By L. Archambeault

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had it speak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

Council for 2002/2003 President S.J. Ramokgopa President-elect T.R. Stacey Vice-presidents Senior F.M.G. Egerton Junior W.H. van Niekerk Immediate Past-president A.A.B. Douglas Honorary Treasurer J.A. Cruise

Jan 1, 2003

Council for 1999/2000 President J.R. Dixon President Elect M.H. Rogers Vice Presidents Senior Dr L.A. Cramer Junior A.A.B. Douglas Immediate Past President R.P. Mohring Honorary Treasurer J.A. Cruise Members of Council B.C. Alberts Dr N.A. Barcza N.J. Barkhuysen R.D. Beck M.J.P. Bierman Prof. A.N. Brown D. Cockcroft Dr M.B. Cortie Dr L.A. Cramer J.A. Cruise E.G. de Villiers J.R. Dixon A.A.B. Douglas F.M.G. Egerton J.P.W. Fisher C.E. Fivaz K.J.R. Ford Prof. G.A. Fourie R. Graham Dr R.G. Gürtunca Dr R.V.R. Handfield-Jones* M.C. Harris J.P. Hoffman H.E. James P.J. Knottenbelt R.P. Mohring H.G. Mosenthal G.Y. Nisbet N.M. O'Brien R.G.B. Pickering Prof. R.P. Plewman S.J. Ramokgopa Prof. R.E. Robinson M.H. Rogers D.A.J. Ross-Watt Prof. R.F. Sandenbergh Dr H. Scott-Russell C.B. Sheppard D.A.A. Smith Dr T.R. Stacey Dr O.K.H. Steffen D.J. van Niekerk J.C. Viljoen J.N. Wallington

Jan 1, 1999

By J. Stacey

This study was undertaken to generate a locally relevant guideline for the socio-economic aspects of mine closure for South African closure practitioners and decision makers. It should also represent a resource for interested and involved stakeholders. Mine closure, and its related post-closure social, environmental and economic characteristics, is part of the lifecycle of mining operations, given the finite nature of the ore resource. Many coal mines are anticipated to close in the next ten to fifteen years in Mpumalanga, as the epicentre of the industry shifts towards the Waterberg. Social aspects of mine closure have been historically underplayed, and under researched. Coaltech thus commissioned two studies, the first of which examined the closure dynamics of 36 mines in Mpumalanga and KwaZulu-Natal in 2006. A follow-up study (July 2007) focusing on Mpumalanga3,4 confirmed some of the results of the first study. It also contained broad guidelines for mine closure covering social and labour planning, job creation, the use of mine infrastructure, developmental incentives, and environmental rehabilitation.

Jan 1, 2010

Council for 2001/2002 President A.A.B. Douglas President-elect S.J. Ramokgopa Vice-presidents Senior F.M.G. Egerton Junior Prof. T.R. Stacey Immediate Past-president Dr L.A. Cramer Honorary Treasurer J.A. Cruise

Jan 1, 2002

By A. W. S. Schumann

A. W. S. Schumann The first reason for todays success lies in the very high standard which was set by our speakers today and I think that we owe a very special vote of thanks to Messrs P. M. C. Wilson, A. A. Oakes, M. J. Deats, A. C. Coetzee, R. E. Burnton and J. G. Ferguson. This, however, cannot account for the fact that there was a tremendous response even before anyone knew who was going to speak or what they were going to speak about. I suggest that the response was enthusiastic because people expected a more informal gathering with a greater opportunity for feedback, for an exchange of views and for questions and answers. The very popularity of the idea has defeated its own ends to some extent. This gathering is too big and many people must have been left with questions unanswered. Possibly one should arrange for a number of meeting places-there are many in the Chamber and the surrounding mining houses-and then have separate meetings in the morning with joint reporting session in the afternoon. Alternatively, we could have a symposium after the colloquium, using Webster's definition of a symposium as as 'a drinking party of merry fellows'. We all know that it is easy to discuss mining into the small hours. Obviously one cannot summarise todays papers and discussions, but I would like to make a few comments on technical matters and after that I would like to speak for a moment about what I see as major trends or tendencies which arise from discussions of this nature. Regarding the question of placing a village on a mine or away from a mine, I would mention that there is quite a body of literature on the adverse sociological effects on the development of children in any community in which the great majority of parents share the same occupation. It is something to be avoided if possible. We discussed the concept of the moving stockpile. If this is proved to be successful, it could save a considerable amount of money for Escom who could then avoid the construction of very large and costly staithes which are now regarded as parts of power stations. One does not see why both a moving stockpile and a staith should be necessary. By the way, speaking of Escom, I see that Mr Bob Scott is here; he has stopped pulling my leg by saying that we sell stone to Escom; perhaps someone has told him that if this is true, it must be the cheapest stone you can buy in this country. My next point relates to the use of epidiascope. It struck me again that this instrument which provides a visual image to accompany your message, can be very effective if it is properly used. These papers speak of a great deal of hard work which went into their preparation, and one really feels that the authors should have taken a few minutes more to prepare their drawings specifically for the epidiascope. There should be nothing on the drawing which is not necessary to illustrate a particular point and there should be nothing on the drawing which is not visible from the back of the hall. In particular, if one cannot read the figures along the sides, then one