Search Documents

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By J. H. Potgieter

The method used to assess the reactivity of lime was evaluated to gauge it usefulness as a quality control tool. The effect of particle sizes, different lime and water masses for a fixed s:l ratio and the same for various s:l ratios on the reactivity values obtained, were investigated. An attempt to introduce the amount of grit produced during the slaking reaction as an additional measure of limeís quality and reactivity, proved to be unsuccessful. It was also found that the relative amount of lime slaked during the different tests was independent of the reactivity value of the lime. The investigation confirmed the usefulness of the accepted test procedure as are liable method to measure the reactivity of lime, despite various reservations expressed from a theoretical point of view.

Jan 1, 2002

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By N. Tatalias, P. Ilunga, M. Lampi, J. Edwards, K. Valkama, M. Nicolle, D. Samal

"Developing a greenfield mining project is a complex exercise: doing so in an increasingly volatile, uncertain, and ambiguous global economy adds significantly to this complexity. In the context of an elevated cobalt price, this paper outlines the metallurgical and process development of the Mutoshi copper–cobalt project for copper cathode and cobalt hydroxide production in the Democratic Republic of Congo. Chemaf has a long production history on the Copperbelt, a region widely perceived to be tough to operate in. This history stretches back to 2001, during which time the company has developed two copper–cobalt processing facilities. The experience gained in the development and operation of these two facilities has been used extensively in the Mutoshi copper–cobalt project. The metallurgical test work, process design, and project delivery approach are presented. Additionally, the decisions taken to minimize risk and maximize upside to the project are discussed. IntroductionChemaf (Chemicals of Africa), a mining company located in Katanga province of the Democratic Republic of Congo (DRC), has been operating since 2001 with two major copper– cobalt processing facilities: the Usoke and Etoile plants. In 2016, Chemaf acquired the Mutoshi mine, which belonged to Gecamines and had been explored by Anvil Mining since 2004 under a joint venture with Gecamines. Chemaf appointed African Mining Consultants Ltd (AMC) to undertake a preliminary economical assessment, then develop a JORCcompliant Mineral Resource estimate and finally a full life-of mine feasibility study. Both a Mineral Reserve and Mineral Resource were developed and the final life-of-mine feasibility study is to be published shortly. A metallurgical test work programme was initiated and carried out by Chemaf’s research and development laboratory with assistance from the Chemaf process team. After completion of the initial test work, Chemaf developed a process design criteria document for a 20 kt/a copper cathode and 8 kt/a cobalt in hydroxide production plant, followed by a flow sheet and supporting METSIM mass balance. As the drilling progressed, the plant design capacity was revised to 16 kt/a cobalt production. The life of the mine at this production rate is over 40 years."

Nov 1, 2018

By B. Genc, C. Gous

Spontaneous combustion during coal mining operations is a major problem that affects the health and safety of workers and causes environmental problems. The phenomenon is associated with the presence of coal, coal shale, and pyrite. In 2020, a premature detonation incident occurred at an iron ore mine where the waste material contains black carbonaceous shale units known to be associated with pyrite. The spontaneous combustion propensity and properties of samples of the black carbonaceous shales from the mine were examined and compared with samples from the Witbank Coalfield. The spontaneous combustion liability indexes of these samples were correlated with X-ray fluorescence (XRF) and proximate and ultimate analyses using linear regression. The Wits-Ehac Index classification results show that the samples were between medium and high risk. The linear regression analysis showed very poor correlations between the Wits-Ehac Index results and the XRF and proximate and ultimate results. The most valuable relationship found is between the presence of relatively high sulphur (greater than 3%) and ground reactivity with nitrate-bearing explosive emulsion.

Jun 5, 2023

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By S. Schutte, J. Pelders

Worker participation in equipment development can result in improved user acceptance and product quality. This paper focuses on worker engagement in equipment development processes in the South African minerals sector. Qualitative data was gathered during interviews with original equipment manufacturers (OEMs) and industry experts. A lack of inclusion in equipment design from workers from all organizational levels in mines was reported. Meanwhile, the historical context and workplace culture of the mining industry (including leadership, trust, training, performance, and remuneration factors) were evident barriers to the implementation of new technology. Worker engagement processes should include securing management commitment, creating multidisciplinary teams, effective facilitation, shared understanding of needs, training and development, and iterative design. Human-centred design approaches and independent platforms for engagement on equipment design requirements are recommended.

Feb 2, 2021

By R. Nyirenda, B. Besa, N. Dzimunya

The accurate estimation of peak particle velocity (PPV) is crucial during the design of bench blasting operations in open pit mines, since the vibrations caused by blasting can significantly affect the integrity of nearby buildings and other structures. Conventional models used to predict blast-induced vibrations are not capable of capturing nonlinear relationships between the different blasting-related parameters. Soft computing techniques, i.e., techniques that are founded on the principles of artificial intelligence, effectively model these complexities. In this paper, we use the random forest (RF) algorithm to develop a model to predict blast-induced ground vibrations from bench blasting using 48 data records. The model was trained and tested using WEKA datamining software. To build this model, a feature selection process using several combinations of Attribute Evaluators and Search Methods under the WEKA Select Attributes tab was performed. The correlation coefficient of the actual data and RF model-predicted data was 0.95, and the weighted average of the relative absolute error (RAE) was 10.9%. The RF model performance was also compared to the equivalent-path-based (EPB) equation on the testing data-set, and it was seen that the RF model can effectively be used to predict PPV. The study also demonstrates that the EPB equation is a suitable empirical method for predicting PPV.

Mar 30, 2023

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By J. Guerrero, O. Pavez, N. Toro, A. Nazer

In the 19th century, mining in northern Chile was of great economic importance. Today, the ruinsof the copper smelters and abundant fragments of refractory bricks from their furnaces remain. Therefractory materials have not been previously studied. the origin, physical and chemical properties, and compressive strength of 10 different samples of historical refractory bricks collected on-site were investigated. The characterization results showed that the bricks are silico-aluminous, unlike the magnesium-chromium bricks used by current foundries. It was determined that 90% of them were produced in the UK and 10% were manufactured in Chile. The phases present are mullite, quartz, cristobalite, and tridymite, and the chemical composition corresponds mainly to SiO2. The compressive strength of the historical bricks is similart to those currently used,. These results may contribute to the knowledge of the 19th century mining and metallurgical historical heritage of Chile and the UK.

Jul 5, 2023

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

"Chairman: Dr W. S. RAPSON Rapporteur: Mr J. W. WILSONPapers:Computer applications in rock mechanics by F. H. Deist, E. Georgiadis and J. P. E. Moris Rock mechanics in the design of mine layouts by K. Hodgson and N. G. W. Cook Automated regulation of mine ventilation by P. NiskanenThe rock mechanics papers, because of their complementary nature, were presented in succession and discussion on both followed directly. The paper on automated ventilation control at a mine in Finland was then presented and the session was closed with several contributions to this paper.By and large the papers and discussions which followed in this session showed how a classic tie-up had developed between the use of computing techniques in important fields of mining, and their practical application. In fact, the dis-cussion following the rock mechanics papers showed clearly that without the aid of high-speed digital computers the rate of progress in applied research in deep-level hard-rock mines, would have been severely hindered. Furthermore, it became apparent from the comments made by several contributors that the rock mechanics techniques and computer progress described in Deist's and Cook's papers could be used to provide useful data in the solving of rock mechanics and design problems on mines other than flat dipping deep tabular deposits.The paper by Niskanen, which described an automated ventilation control system at a mine in Finland, showed how effective computers could be in areas where the reversal of mine ventilation occurs due to severe seasonal temperature ranges. Although the system described in the paper could not be introduced easily in complex underground mines, several contributors gave examples of similar ventilation problems that could be solved mechanically,In introducing his paper, Dr Deist said that the purpose of the paper was to give a brief account of some of the programs designed by himself and his co-authors to aid in the solution of rock mechanics problems,The first system presented by Dr Deist was known as MINSIM in the South African mining circles. This system was designed specifically to aid in the solution of rock mechanics problems in the South African gold mining industry. It was particularly designed to handle tabular deposits at great depth but it has been used satisfactorily on a number of occasions to obtain at least approximate solutions in other mining situations. Dr Deist said that the principles embodied in the programs were easily extended and, in fact, there was a project in progress at that time which was aimed to do this. He said that the principles could easily be extended to shallow-depth mining at steep or very steep inclinations."

Jan 1, 2014

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By M. Z. Emad, N. Abbas, Y. Majeed

Room-and-pillar mining is commonly employed for the extraction of rock salt in undergroundmines. Pillar stress is a major concern in these mines as it is directly related to stability and mineralrecovery. In this study a flat jack method was used to measure pillar stresses in three undergroundrock salt mines in Pakistan. The field work included determination of in-situ stress, in-situ elastic modulus, recording of field variables (pillar length and width, height and width of opening, opening width to height ratio, extraction ratio, and overburden height) and collection of salt block samples. The geomechanical properties of rock salt (uniaxial compressive strength, Young’s modulus, Brazilian tensile strength, and density) were also determined to estimate overburden stress, pillar strength, and factor of safety (both estimated and actual). It was found that the measured pillar stresses are proportional to the overburden stress values, with their magnitude ranging from 6.05 MPa to 11.97 Mpa, and the pillars were found to be stable. Regression analysis was performed to develop statistical models for in-situ stress and in-situ elastic modulus. Finally a quick guideline chart was developed to determine the suitable length of pillar for a given span and required level of safety.

Jun 5, 2023