Search Documents

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

By C. Aldı, O. Yaral

For the more economical excavation of tunnels in underground mining activities, the selection of mechanised excavation machines (such as roadheaders, electro-hydraulic drills, etc.) and the analysis of performance prediction that can be used in estimating machine energy consumption have been subjects of research from past to present. One of the parameters to be considered in studies examining these methods, is the grinding process. The success of increasing efficiency in grinding is expressed by a reduction in energy consumption. The goal of a grinding process is to maximise the grinding amount at the appropriate grinding size while minimising the energy consumption per tonne of the fragmented material. Today, the depletion of high-grade ore deposits has largely directed the mining industry towards low-grade but large reserve ore deposits. This shift has particularly increased the importance of the grinding process, as it is dependent on particle liberation. Grinding is a critical step in reducing the mineral to the appropriate size, and energy consumption poses a significant challenge in this process. As a result, researchers have conducted various studies focusing on energy efficiency and cost optimisation in this field. In this study, the grindability of 7 different coal environment rocks (sandstone, siltstone) from the Zonguldak Basin, Uzulmez Region was investigated. For this, Hardgrove Grindability Index and Bond Work Index tests were conducted. While determining the relationships between grindability and other parameters, the results obtained from the Hardgrove Grindability Index (HGI) test were used. The energy values found in the Bond Work Index (BWI) test were used to evaluate the excavatability of the rocks. Additionally, tests for strength, hardness, drillability, and abrasiveness were conducted to observe the impact of other parameters on grindability. Considering the results obtained from the experiments, significant relationships were found between the grindability of the rocks and other parameters.

Mar 30, 2026

By T. Grewar

"South Africa is a water-scarce country, rated as one of the 30 driest countries in the world. Worryingly, government expects water demand to outstrip supply as early as 2025. The South African government believes that substantial volumes of water can be made available through the reuse of treated mining-impacted water. Currently, however, large volumes of treated mining-impacted water are produced, often with no end use in mind other than discharge or disposal, when these treated effluents may have further uses in applications which are currently and unnecessarily using high-quality water. Treating the wastewaters to levels that meet ’fitness-for-use’ guidelines for alternative applications such as agriculture, sanitation, or industrial processes will reduce the treatment cost burden compared to potable water production. The primary conclusion of this review is that the most suitable option for re-using treated mine-impacted water is in agriculture, for irrigation of crops (food, forage, or energy crops), which currently and unnecessarily makes use of the majority of South Africa’s high-quality resources or potable water. Other findings include the realization that although guidelines and legislation for water re-use in South Africa exist and are readily available, they tend to be contradictory and confusing in many cases. It is imperative that these ambiguities and incongruities in the available guidelines and legislation for water re-use be clarified and updated swiftly IntroductionSouth Africa is a water-scarce country and is currently rated as one of the 30 driest countries in the world, with an average rainfall of 490 mm/a, approximately half of the global average. As an indicator of the degree of regional variability in South Africa’s water supply, it has been shown that 70% of all runoff is from approximately 20% of the land area. Regardless of the water scarcity faced in South Africa, our water conservation track record is poor, with an average consumption of 280 L/d per person, almost 60% more than the global average of 175 L/d per person. Around 40% of this allocation is utilized in watering lawns and gardens (Zhuwakinyu, 2017).The South African government predicts water demand to outstrip supply as early as 2025. On an international scale, the situation appears just as dire, with the United Nations High Level Panel on Water (HLPW) expecting a 40% water shortfall by 2030, which may affect up to 1.8 billion people based on current water demand trajectories (Zhuwakinyu, 2017)."

Mar 1, 2019

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10?15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed, and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2013

By F. M. Ramadhan, M. R. Pratama

Monitoring open-pit mine road conditions has become very critical nowadays. There are several benefits to in conducting research on this field such as opportunity to improve truck’s speed which directly influences truck’s productivity. This research aims to provide a semi real-time, and sensors-based automatic road damage detector that predicts the road quality through road damage exact location tracing, road damages auto-classification, and real-time instruction in the form of work order format to mining road maintenance, and repair authorities through mobile apps and maintenance unit’s in-cabin display. It will also provide the maintenance/repair activity performance evaluation via integrated dashboards. The artificial neural network algorithm is applied during the process of data training regarding classifying road damages and severities which resulted in a valid model. The road damage classification model has a precision level of 80.5% in predicting whether the road is damaged or not. Using this approach, we are expecting to visualise a road quality map of all active roads on mine site.

Sep 1, 2021

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By W. J. van Wyk, W. I. Mahne, G. Priest, C. du Toit, W. A. Liebenberg

Prior to the Coalbrook disaster in 1960, bord-and-pillar mining of the number two seam in the Witbank coalfields often resulted in small pillars with low factors of safety. At the Goedehoop Colliery, number two seam pillar stability is also affected by top and bottom coaling, while at Greenside Colliery, stability was further reduced by additional loading from a surface mineral residue deposit. This compromised the stability of the number two seam workings, impacting the safe mining of the overlying number four seam reserves. To extend the life of mine of both operations, an alternative risk management approach using designated enhanced monitoring districts was implemented to safely mine the number four seam reserves. This paper presents the use of geophone arrays to monitor micro-fracturing in number two seam pillars and the interburden between number two seam and number four seam, thereby enabling early detection of potential instability during overmining of the number two seam. Risk was assessed using fault and event tree analyses to determine acceptable failure probabilities. Automated seismic data processing distinguished micro-fracturing from noise, supported by extensive evacuation procedures for effective risk management. This approach facilitated the safe extraction of 4.70 Mt of number four seam coal. The study quantifies the efficacy of geophone monitoring in optimising coal recovery over low factors of safety pillars and assesses the application of Van der Merwe’s (2019) time-based formulae for pillar stability analysis for this project.

May 8, 2026

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

By M. Dhainaut

This paper presents computations of the electric field inside a furnace. We first look at the effect of contact between two coke particles from an electrical point of view. We give values for the amount of contact resistance in the total resistance of the system formed by the two coke particles. We show that the effect of contact resistance decreases rapidly with increasing contact area. We then look at the complete electric field inside a full scale furnace. The aim is to evaluate the amount of current that short-cuts the metal bath for different vertical positions of the electrodes. We show that electrodes high above the metal bath are undesirable since they offer a larger surface of conductive charge materials where current can flow through. On the other hand, deeper electrodes force the current to go the whole way down to the metal bath. Ohmic heating along this path ensures a high temperature of coke and slag that are beneficial for metal recovery.

Jan 1, 2004

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024

By P. J. H. de Graaf, S. D. N. Wessels

"Rio Tinto’s Western Australian expansion, combined with mining within structurally complex geology and increasingly below the water table, presents challenges in effective slope management to ensure safe and economic mining.The Geotechnical Management System (GMS) was developed by Rio Tinto Iron Ore (RTIO) to manage geotechnical risks identified during the design process and implementation, and to ensure feedback based on the ‘as-found’ conditions. The GMS utilizes a risk-based approach to geotechnical risk management and is centred on the geotechnical risk and hazard assessment management system (GRAHAMS). GRAHAMS is used to assess pre- and post-control risk for future potential risks (planned slopes), current risks (as-built slopes), and actual geotechnical hazards (realized risks) identified in the pit. This serves as a core operational risk management tool in identifying and prioritizing key risk sectors and management of critical controls. The system’s database reporting functionality supports effective communication of operational risks to operational personnel, as well as reporting the risk profile across operations to management.A rigorous engagement process between design engineers and sitebased engineers is implemented to ensure that key design assumptions, limitations, risks, and opportunities are understood by the site teams. This information, together with mine plan schedule details, is used to assess the design risk and develop appropriate controls. These controls typically include slope performance monitoring and slope reconciliation. The design feedback loop is closed through sharing of key slope performance and reconciliation data with the design teams.The GMS has been successfully implemented in RTIO pits and is fundamental to successful geotechnical slope management. Improved characterization of design assumptions has allowed for re-assessment of the pit design and improved hazard management in high-risk pits. The GMS, GRAHAMS, and other processes reduce the incidence of unexpected slope instability. Improved understanding of rock mass conditions has allowed for economic optimization through redesign of slopes, allowing for an improved understanding of risk and fewer unexpected conditions (surprises), hence an increased realized value."

Jan 1, 2016

By F. T. Cawood, T. Chikande, H. R. Phillips

Underground mines require electricity to operate both the main surface fans and auxiliary systems, with primary ventilation systems typically accounting for approximately 40–60% of the mine’s overall electricity consumption. The primary reason for this considerable expense is that most underground ventilation systems are designed for peak demand, regardless of the actual demand, which is commonly dictated by diesel equipment usage in trackless mining operations. Most platinum mines on the Great Dyke in Zimbabwe tend to operate their ventilation systems at this peak level, despite the mine’s air quantity being well in excess of the ‘true’ ventilation needs. This is due to a lack of appropriate ventilation controls. The authors designed and installed a ventilation-on-demand system at one of the bord and pillar platinum mines to minimize the use of redundant air in underground operations. Fourth industrial revolution techniques were applied to the environmental monitoring and tracking systems thereby optimizing air quantity demands. The mine managed to reduce its annual power consumption by 23% through the implementation of manual control and time-of-day scheduling levels of the ventilationon- demand concept. There was also a 6% productivity improvement, mainly attributable to an increased face time as a result of the significant reduction in the re-entry period following a blast. This paper introduces a novel concept of ventilation optimization through digital transformation targeting mainly room and pillar platinum mines. A system was designed, installed, and commissioned, though there is currently an ongoing optimization process to harness the full benefits such as productivity enhancement, reduced power costs, and improved worker health.

Dec 13, 2022