Search Documents

The simple act of taking a sample implies that someone will use the information contained in the analytical result to make a decision about a course of action. In the mining industry, the decisions may involve huge capital commitments for opening or closing a mine, or marginal tactical costs that involve deciding if a truckload of mineralized rock should be sent to the mill for processing, or the waste dump. Sampling is among the most fundamental activities in a mining operation, and this paper aims to examine some of the technical issues that can assist in ensuring that samples are representative and correct. Insights into the scale of variability require that we disaggregate sampling variance into its component parts and evaluate each one individually. The work of Pierre Gy in understanding the different sampling errors is the first step in establishing an optimal protocol. This must be followed by the appropriate measures to ensure the protocol is implemented such that minimal bias is introduced in the sampling process. Even with these insights the possibility exists for large unseen and hidden costs can accumulate in a mineral development because of sampling errors. These hidden costs arise due to misunderstanding of the principle factors that affect the size of sampling errors, such as the mass of the sample, the effects of splitting a sample to reduce the mass, and the influence of the nominal particle size. The handling of sample material without due regard to the sampling characteristics of the material being sampled is also a major source of sampling errors. The most significant problem is due to the influence of the so-called volume-variance effect. This effect is a consequence of the support effect and the information effect both of which relate to the difference in size at which samples are collected and mining blocks are extracted. The information effect is a function of the availability of data at the time that decisions are made about the destinations of mineralized rock, namely the mill or the waste dump. Implementation of appropriate sampling protocols in the mineral value chain remains a challenge throughout the industry. The growing understanding and deepening appreciation of sampling theory and methods means we stand on the threshold of a new era for implementing and understanding appropriate sampling procedures and protocols. In the interests of optimal development of the national patrimony it is suggested that standardization through the identification of structural problems and continuous improvement of mining processes be instituted at a national level.

Jan 1, 2007

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By D. Pohl

The past decade has seen rapid expansion in the West African mineral exploration environment. This expansion has been largely driven by changes in ?Political climate ?Fiscal and legal regimes ?Exploration approaches ?West African geology. Major regional mapping and geochemical surveys by the UNDP, and the BRGM in the late 1970s and early 1980s laid the foundation for the rapid development of mineral exploration and resources during the past decade. An additional driving impetus was the discovery by native artisanal miners of many significant new gold occurrences at Libiri, Essakan, Bouda and Tirahori, during the great droughts of the late seventies and early eighties.

Jan 1, 1998

By L. K. Bandyopadhyay

The expert system component of Knowledge Base System supports the analysis and interpretation phases of ventilation design with an algorithmic program used for the solution of alternate design. The paper describes the ?ES-VENT? knowledge based system developed at Central Mining Research Institute, Dhanbad, India for an on-line diagnosing of the ventilation problems using the ?IITMRULE? expert system development tool. In the ?IITMRULE? expert system tool, it has been decided to use a backward chaining reasoning process to reach the goal state i.e. the final conclusion. ES-VENT system is made of three modules: On-line Data, Diagnostics and KBS. Each module is being a collection of several programs. The paper mainly deals with the parameters affecting the ventilation of underground mines such as air-velocity, air pressure, temperature, dust, and humidity and gas contents. The graphical presentation of these parameters on the computer and the interactive part of the developed program is expected to help a ventilation officer to determine the changes in a ventilation circuit necessary to bring the mine ventilation to the desired value. Once such changes are physically effected, the display will indicate if the changes have brought the desired effect or not on ventilation. Keywords: Ventilation network, on-line data, expert system, intelligent system, knowledge base, inference engine.

Jan 1, 2002

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By M. F. van der Merwe

Anglogold Ashanti?s Kopanang Gold Plant (previously No. 9 Gold Plant) treats ore from Kopanang and Tau Lekoa shafts. The plant is twin streamed and has dedicated treatment circuits, from milling to final product, for each shaft. Waste rock material is used to compensate for the mill gap on both streams. Each stream consists of three 4.85 m x9.15 m ROM mills in closed circuit with a single stage hydrocyclone, milling an average of 7 000 t per day. The liner configuration in each mill consists of six rows of 30 grid liners along with rectangular lifter bars. The topic of gold lock-up is not new and has been investigated and reported on many times, both within Anglogold Ashanti and the broader mining industry. Although the lock-up mechanism is understood, its measurement is neither practical nor precise. The initial lock-up in a new liner and the release as the liner wears down cannot be accurately quantified. Previous test work carried out on Kopanang Gold Plant (with a ?gold scanner?) measured the natural gamma radiation emitted by uranium. This radiation is in proportion to the mass of concentrate locked up in the grid liner pockets, as well as between the cast-on backing plate and the shell. The ratio of concentrate lock-up was estimated as 35% behind the liners and65% in the pockets. Mill gravity concentrates are recovered during routine relining operations from behind the grid liners at Kopanang Gold Plant. Prior to relining, the liners tend to release the concentrate from the pockets as the liners wear. Historical Kopanang data from actual ?mill gold? smelted indicates that an average of 29 kg gold is recovered from behind each row. This indicates a total lock-up of 250kg gold per mill. This locked-up gold should preferably be minimizedor eliminated for the following reasons: ?The cyclic build-up and release of gold in mills complicates accounting ?Gold concentrate arising from liners is a security risk and creates a major mechanism for gold theft ?Loss of interest on the value of 250 kg fine gold is significant and was a major driver for the project. These factors led to the need to develop techniques to eliminate or at least minimize the gold lock-up in the mills. Wave liners, with rubber inserts, have been successful in eliminating lock-up, and were tested at Kopanang Gold Plant in November 2000. However, due to increased load-slip and high wear rates associated with these liners, this option proved less economical in terms of liner wear. Grid liners, with rubber-filled pockets, demonstrated a very high wear life and eliminated pocket lock-up. This system was successfully trialed in January 2003, but unfortunately did not prevent lock-up behind the liners. Current developments have resulted in a system that eliminates both pocket and backing plate lock-up. The conventional grid liner design has been modified to remove its steel backing plate. Rubber inserts that are integrated onto a rubber backing plate, have been designed to be used with the newly modified grid. The backing plate and grid pockets are now completely occupied by rubber, thus completely eliminating concentrate build-up around the new grid liner system installed in November 2003. Results to date are promising and liner life is expected to exceed conventional performance.

Jan 1, 2005

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By L Dyer, G. J. Wilkie, P. Walters, B Tadesse, L. Keeney

Grade Engineering® is a term trademarked by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and includes five key levers for upgrading ores and rejecting waste prior to expensive downstream comminution and mineral processing. These five levers include natural deportment, induced deportment, bulk sorting, particle sorting and gravity separation. Over the past ten years, CRC ORE has progressed a range of technologies that exploit these levers from laboratory proof of concept through to large scale demonstration and validation. This paper details the work carried out by CRC ORE and Curtin University for assessing the amenability of an ore for its natural deportment and particle sorting attributes in an Integrated Screening and Particle Sorting (ISPS) Grade Engineering® process. ISPS is seen as a preferred method for Grade Engineering® as compared to individually operated unit operations as the benefits of each can be complementary. Furthermore, it is suggested that integrating the two levers has two important impacts: 1. Firstly, there is a risk that isolated particle sorting test results will be misinterpreted as being representative of the full sample without considering the mass balance impact of high-grade material that might have been lost in the fines fraction. This fine fraction will not be detected through the particle sorter. 2. Secondly, and potentially of more valuable impact, is that the opportunity may exist to upgrade the feed first through determining if there is a concentration of high grade to the fine (or coarse) fraction which can be separated through screening. Undertaking screening in the preparation stage of the particle sorting process will enable analysis and separation of the fine or coarse fractions of a rock mass. The result of this study provides the mining industry with an independent framework for undertaking an Order of Magnitude (ISPS) Grade Engineering® assessment on a range of constituent ore types. Keywords: Grade engineering, particle sorting, grade by size fractionation

Jan 1, 2020

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By D. J. Fourie

During the production of pure TiO2for the pigment industry, ilmenite, containing 35?60% TiO2, is reduced to high titania slag, containing 70?95% ?TiO2? and pig iron. The high titania slag produced, consists mainly of titanium in different oxidation states and FeO in equilibrium with liquid iron. To predict the phase and chemical reaction equilibria in a furnace, a suitable solution model is required with accurately determined binary interaction parameters, as slag melts tend to behave very non-ideally. This paper investigates two popular slag models, namely, modified quasi-Chemical (MQC) model and the cell model and provides the binary interaction parameters based on recently published data of the ternary system and critically assessed published unary and binary data. Very few modelling results have been published on the ternary Ti-Fe-O system pertaining to high titanium slags. The solution models, with their regressed interaction parameters, can subsequently be implemented in commercial software of the slag-metal phase equilibria to predict how much and which type of solids will precipitate for a given bulk slag chemistry and operating temperature or, alternatively, above which temperature should a furnace be operated to avoid excessive solids precipitation.

Jan 1, 2005

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

"I have been involved in the refractory industry for many years and at some time or another I have designed materials, tested materials, manufactured materials, installed materials, in fact I have done everything except actually chemically analyzed a refractory material.So I would not even begin to tell you how to analyse a refractory material. I'm sure everyone here knows more about chemical analysis than I do.However you could regard me as a customer with and perhaps the insights I have developed may help in putting the role of chemical analysis in the Refractories into perspective.For a start, let's take a step back and ask why we test refractories. The refractories handbook of the American Foundry Association gives four reasons:1. To determine appropriate specification.2. For quality control, to ensure conformance to specifications.3. To provide special property information not available elsewhere.4. For postmortem analysis to determine property changes in service and provideinformation that can point the way to better service.I want to discuss these points with regard to the role of chemical analysis and in particular the abuse of in house chemical analysis facilities. Let me talk first about detelmining appropriate specifications. Most refractory products are made from alumino-silicate raw materials.The phase diagram for alumino and silica is as follows:"

Jan 1, 2014

By E. Van Der Lingen

This paper provides a review on coloured gold, platinum, andpalladium intermetallic compounds, and discusses the models thatwere developed to obtain these materials. These compounds have acrystal structure of high symmetry, such as the CaF2or CsClstructures, ensuring distinct electron band structures. Variousexamples of coloured gold, platinum, and palladium intermetalliccompounds are provided. More in-depth discussion is provided on thepurple gold (AuAl2) and yellow platinum-aluminium (PtAl2)compounds with CaF2structure, as well as the purplish-pinkpalladium-indium (PdIn) compound with CsCl structure. Precious metal intermetallic compounds are used in jewellery andprovide a new dimension to design. Some of these compounds havealso found use as barrier coatings on turbine blades for jet engines,and more recently, research has been conducted into their potentialuse as catalysts, electro-catalysts, sensors, capacitors, and fordecorative coatings.

Jan 1, 2014

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985

By A. V. Peake

Continuous Mining presents an opportunity to extract reef in the stope ?continuously? by integrating the drill and blast activity using propellants or low energy charges. To date, the majority of effort spent on Continuous Mining systems has focused on developing an effective rock breaking process (micro breaking process), and to some extent, eliminating fumes and dust. The perceived benefits of applying low energy charges have been identified as: ?Concentrated mining yielding face advances of 40 to 60 m per month ?Lower stoping widths through better-controlled breaking ?Increase in the advance per blast ?Increase in labour productivity ?The potential to mine reefs where specific conditions make conventional mining uneconomic e.g. reefs with shales in the immediate hangingwall. However, the ability to successfully use low energy charges to create a ?Continuous or Semi-Continuous? mining method is dependent on overcoming the following challenges. ?Improving reliability of rock breaking. This is dependent upon achieving:? Improved drilling accuracy, and? Successful stemming or gas confinement, particularly in fractured rock ?Reducing gas and dust levels ?Reducing high costs. Through the research carried out in Future Mine, many different low energy rock breaking methods and systems were investigated. Whilst detailed results cannot be published here, the guidelines for overcoming low energy rock breaking challenges are discussed.

Jan 1, 2003