Search Documents

By J. Cygankiewicz

Efficient prevention of mine fires is impossible without predicting the self heating processes in the given geological and mining conditions. The respective forecasting method is presented in this paper based on the following assumptions: - factor deciding on fire hazard in the underground workings is the process of heating of coal from the primary rock temperature to the critical temperature when the heating rate growth rapidly - another important factor is the fire incubation time defined as time needed to achieve the critical temperature. This time is determined by balance of heat and mass in the heated coal - contact of crushed coal with oxygen in air cause some exothermic processes as : physical and chemical sorption of oxygen , oxidation reaction and evaporation of humidity Heated coal transfers its thermal energy to the environment by conductivity to the rocks and by convection to the flowing gases. The heating is possible if thermal energy generated from coal is greater then the share transferred to the environment. The paper presents the laboratory method of measurement of heat generation in adiabatic conditions. Also the mathematical model with examples of computation enabling to forecast the self heating process of crushed coal is presented.

Jan 1, 2003

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX, indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential to be higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and alack of collector interaction with the mineral is not the reason for the low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By M. Gous

Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC-arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC-arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilization and furnace stability, complemented by continuous improvement drives, will be thevehicle to drive performance in the short-term, with longer-term performance enhancements due to strategic process development. Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC-arc furnace, titania slag, pig iron

Jan 1, 2006

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By W. H. Van Niekerk

The metal zinc has been around since only about 1400 AD. This may sound like a long time, but when compared to fellow base metals copper and lead, which were discovered in 5000 and 4000 BC respectively, it is evident that zinc is a fairly new kid on the block. This may also be the reason why many new facts and benefits of zinc are still being discovered. For instance, it has been discovered only in the last few decades that virtually no life on earth is possible without zinc. In this address it will be shown that zinc is not only very useful to mankind, but is in fact vitally important for all forms of life. It will be shown that zinc is natural, zinc is essential for life, zinc protects, zinc contributes to the well-being of society and that zinc is fully recyclable. It is therefore hoped, that by the end of this address, zinc will no longer be viewed only as the metal that is responsible for the nice colour of roofing sheets and steel buckets, but may indeed be man?s best friend.

Jan 1, 2005

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By M. Mikolás, L. Pomothy, K. Špakovská, M. Vanek

"Enterprises are faced with increasing economic competition and managers are obliged to look for methods that will ensure a competitive edge in their companies’ markets. These methods include managerial concepts that employ common sense and are low cost. One of these approaches is the KAIZEN methodology, of Japanese origin; kaizen means continuous improvement (CI) when translated. A mining company, despite some of its idiosyncrasies, is just an enterprise where the application of KAIZEN can be advantageous. The company investigated, OKD, is the only domestic producer of hard coal in the Czech Republic and operates four mines that produce 11 Mt of coal annually. The OKD management team opted for KAIZEN as their principal method of continuous quality improvement. This paper suggests ideas for development and application of processes that provide for continuing improvement of production and management. The authors have taken the OKD Company to be their benchmark in the field of mining activities. The paper also focuses on possible difficulties accompanying the introduction of CI sustainable methods. Three years of application of CI methods has increased the income of the company by almost US$38.1 million, which provides a strong argument for continued application."

Jan 1, 2015

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

The statistical methods described in the previous chapter permit the estimation of the average value p of a deposit, and the calculation of confidence limits for this value. They are based on the assumption of independence of sample values. As soon as a reasonable number of samples has been obtained from a deposit, local valuation, or estimation of blocks of ore within the mineral deposit, becomes necessary. The assumption of independence of values must then be rejected. Local valuation is possible only if there is a relationship between the value of a sample and the value of the surrounding ore, provided this relationship is a function of the position of the sample with respect to the blocks of ore to be valued. Whichever method is used for the valuation of a block of ore, the following assumptions are always made: ? The values of samples located near or inside the block are related to the value of the block. ? The values of the samples located closest to the block are most closely related to the value of the block. These assumptions will hold true only if the following assumption can also be made: ? There exists a relationship between sample values which is a function of the distance between samples. We are saying that the value x (z) of a sample centred at a point z has properties which are functions of this point. A certain spatial structure exists in the sample distribution. We are therefore dealing with a regionalized phenomenon, and we must treat x (z) as a regionalized variable. This can be done statistically by means of a model chosen to represent the spatial structure of the phenomenon. We shall see that the relationship between block values and sample values can be deduced from the relationship between sample values, and all local valuation problems can be solved using the statistical model obtained from the analysis of the sample values. It is important to realize that this statistical model is obtained by analysing the properties of known sample values, and will be used for the estimation of unknown block values. Such a statistical inference is valid only if the model developed represents the properties of both the sampled section of the ore body and the section to be valued: some stationarity conditions must be satisfied, and the model with the least restrictive conditions is preferred. In the following chapters, the most important models used in spatial geostatistics are presented. The models which can be used when there is no significant drift (trends) in values are described in Chapters 3-1 1. These models can also be used to solve some specific valuation problems when a linear drift is present. A general study of the more difficult problem of analysis of an ore body whose values present a drift is described in Chapter 12. Note that the area considered for local valuation of a block of ore is often small enough for any drift which might be present to be ignored.

Jan 1, 1978

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003