Search Documents

[ ]

Jan 1, 2009

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By C. J. Fauconnier

The main purpose of the paper is to determine the contribution of fluctuations in barometric pressure to flammable gas explosions in South African mines. For this purpose, the barometric-pressure patterns preceding each of the 59 major explosions in South African gold and coal mines over the past 20 years were analysed. It is concluded that diurnal fluctuations in pressure do not have a major influence on the accumulation of gas in the underground workings, but that pressure drops associated with cyclonic weather systems moving across the country over a number of days are the major factor contributing to gas explosions in mines. To illustrate some of the points made in the paper, the Hlobane Colliery explosion of September 1983 is used as a case study. In the final section, several general conclusions are drawn and recommendations put forward as to how mines should recognize and react to meteorological phenomena that may lead to an increased probability of gas explosions in underground workings.

Jan 1, 1992

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d'une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d'années de développement de ce projet depuis les premières études jusqu'à l'exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

By H. J. S. Kriek

Methods are described by which increased production is achieved whilst retaining full availability of equipment and decreased refractory cost. Refractory materials have certain limitations, and when these limitations are known the variables in operating practice having the greatest impact on refractory life can be controlled. The most important factors to be closely controlled are porosity, chemical constitution of refractory materials, slag basicity, slag volume, FeO content of slag and temperature at which the process is operated. Knowledge of the process is invaluable in deciding on the type of refractory to be used. The types of refractories used in and the operating variables of the ironmaking, steel making and steel finishing units are described.

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

By B. Samanta

A quality characteristic analysed through construction of the Shewhart control chart is required to be normally distributed. In mining applications, this assumption is often violated as many quality characteristics follow skewed or lognormal distribution. In this paper, two methods were investigated using a heuristic approach for setting up the control limits for a skewed population. Based on these approaches a Mode chart, and a Weighted Variance (WV) control charts were constructed. The performance of the proposed methods was compared with the normal based Shewhart method through a case study conducted in a surface mine supplying iron ore to a steel plant. A simulation study was also conducted to evaluate the effectiveness of the proposed methods over the Shewhart method. The study revealed that the Shewhart control charts generated more out of control alarms compared with the Mode and Weighted Variance control charts for a skewed population of Fe%. The simulation results also revealed that for extremely high skewed population, the WV control chart and Mode control chart provided higher probability of coverage than the Shewhart method; although the detection rate (probability of detection) of out of control condition for these methods was slightly reduced compared with Shewhart method.

Jan 1, 2004

By R. Hemp

The first part of this paper describes the collection of barometric pressure measurements in a mine and their statistical analysis, which shows the effect of variations in barometric pressure, both on the primary emissions of methane gas into the workings (whether from fissures or from the surrounding strata), and on the flow of air to and from large unventilated, or poorly ventilated, areas. The second part of the paper deals with a study, based on computer simulations, of leakage flows of air into and out of sealed areas, and the reduction of such flows by the use of adequate seals.

Jan 1, 1994

By E. J. Magri, R. M. Murray

This paper describes the application of linear programming to the monthly 'set up' planning of stopers' sections on two gold mines. On one of these mines, the purpose of the exercise was to maximize the total stoping production (measured in centares per month). On the other mine, the maximum stoping contribution (rands per month) was required. Maximization was to be achieved through improved planning, independently of the various other productivity improving activities that were taking place at the same time. The results to date show that, when linear programming is used, an average increase of about 9 per cent in stoping production (or contribution) can be obtained for these two mines.

Jan 1, 1978

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004