Search Documents

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By J. Ojeda, R. Kuyvenhoven, M. Ziemski M

This paper focusses on the identification of operational opportunities in a 1100 tph pellet plant to reduce the specific energy consumption in its comminution circuit, which is designed to process magnetite ore and produce pellets to be used as raw material in the iron and steel industry. The assessment is carried out through a frequency analysis for three of the four processing lines of the plant, consisting of one ball mill each with an installed power of 4.5 MW and 280 tph of mill throughput design capacity. The methodology, as described in this paper, facilitates the visualisation and quantification of plant performance and provides a good first approach to prioritise alternatives for optimisation. In a pellet plant, grinding is a critical stage due to its high energy consumption and its major impact on the physical properties of the iron pellets, which quality depends to a large extent on grind size and Blaine index. From the evaluation that was performed it can be concluded that production line 2 has the lowest specific energy consumption of 15.1 kWh/t, while line 1 has the highest with an average of 16.6 kWh/t for the same type of ore. On the basis of the results and current operational practices, it is recommended to increase the average mill throughput from 240 tph to 265 tph, translating into specific energy reduction of 10%, without affecting the chemical and physical properties of the final product. The implementation of an HPGR for regrinding the magnetic concentrate is proposed to assure adequate specific surface area in case grinding coarser becomes an alternative, which would also be beneficial for the subsequent water recovery stages. Keywords: Iron ore pelletisation, grinding circuit, energy efficiency, particle size, frequency analysis

Jan 1, 2020

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10 km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal orebody, is geologically complex. A relationship between its geological variability and the associated mineralization has been established by defining a number of facies types. The Merensky Reef has been subdivided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 potholefacies, FW3 pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralization. The pothole facies, in contrast, has mineralization located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the orebody. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situ grades estimated as an input to the mine planning process.

Jan 1, 2007

By Monica M. Cole

The Empress nickel/copper deposit west of Gatooma in Rhodesia occurs within gabbro and amphibolite, disposed at the contact of a granodiorite stock (Barebottom Hill) and the surrounding greenstones of the Archaen Bulawayan System. The orebody has a pipelike form and a poor surface expression due to plantation of the area by Miocene (Africa) and later Victoria Falls erosion cycles. Barebottom Hill represents a monadnock remnant in the geomorphological surfaces while traces of the once larger Empress orebody have been removed. Limitations in soil geochemistry necessitated both studies of the vegetation ecology and the biogeochemistry of the area, both of which were anomalous. The use of geobotany was found to be restricted but biogeochemistry offers a most effective prospecting tool and was found to define the sub-outcrop of the ore-body more precisely than soil geochemistry since these methods reflect and differentiate anomalies emanating from bedrock mineralisation and those due to surface phenomena.

It is well understood that to develop wagon wheels with higher abrasion resistance, fracture toughness, and fatigue resistance, steels with lower amounts of inclusions need to be used. Clean steels are produced with technologies that minimize the amount of inclusions in the microstructure. The demand for cleaner steels is high, and lowering of non-metallic oxide inclusions and controlling their morphology, composition, and size distribution is vital. Reduction of residual impurity elements such as sulphur, phosphorus, hydrogen, nitrogen, and trace elements is essential in the production of cleaner steel. Material cleanliness is vital for fatigue endurance, since oxide inclusions may act as stress concentrators and initiation points for fatigue cracks. To better understand the relationship between the cleanliness and toughness of the 34-inch cast wagon wheels, two samples of different levels of cleanliness were supplied for investigation. This paper presents the results of metallurgical analysis using scanning electron microscopy(SEM), energy-dispersive spectrometry (EDS), and mechanical tests for the pearlitic high-performance cast rail wagon wheel (identified as Class B) that are currently being used. The Charpy V-notch impact test results for the three samples from wagon wheels were compared. With the aid of SEM/EDS analysis system, non-metallic inclusions in these steels were detected, and it was possible to determine the position, size, shape, and composition of each particle. Alumina and manganese sulphide inclusions could be identified as the dominant inclusion types in the investigated samples. Fracture surface analysis of the Charpy specimen with high inclusions indicated that transgranular cleavage was the predominant fracture mode. Fractography of fracture surfaces of Charpy impact test samples also showed improvement of toughness properties on the clean sample.

Jan 1, 2013

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

By E. Spicer

X-Ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems in XRD creates the opportunity to use this technique in modern process control. In the analysis of heavy mineral sands, XRD can identify the main mineral phases, such as ilmenite FeTiO3, rutile TiO2, Zircon ZrSiO4and quartz SiO2, and any other minor components present, such as anatase TiO2, magnetite Fe3O4, haematite Fe2O3or monazite (Ce, REE)PO4. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis (Bish and Howard, 1988) are attractive alternatives, as they do not require any standards or monitors. These methods offer impressive accuracy and speed of analysis. The Rietveld method compares calculated versus experimentally derived X-ray powder diffraction patterns for the sum of all crystalline phases. Another analysis technique offering great benefit to mining industries is cluster analysis. Enormous amounts of XRD measurement data are generated during the process control and material evaluation. New ways of handling such vast amounts of data are required to produce meaningful information for the end users. Cluster analysis greatly simplifies the analysis of a large amount of data from different processes or different raw materials, and automatically sorts closely related scans of an experiment into clusters and marks the most representative scan of each cluster as well as outlying patterns. The use of cluster analysis to evaluate the XRD data allows fast and reliable tracking of the process. It is the most economical procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimization methodologies, results, data precision and limitations will be discussed. The approach has potential as a relatively inexpensive, reliable tool, useful in the characterization of heavy minerals sand materials.

Jan 1, 2007

By M. Berjak, D. M. Hawkins, V. E. Marting, R. B. MacGillivray

Contributions to discussion V. E. Marting (Associate Member): The authors of this paper should be congratulated in having pioneered the application of the Sharapov predictor to local data, and in having made a valuable contribution to South African experience in the quantitative treatment of geological information using a digital computer. Although the existing set of three programmes has been described as a 'suite' it does not represent an integrated system in the accepted sense since the communication between runs is made in the form of punched card files to enable the mining engineer to exercise discretion and control over the data entered at each phase. Although the authors are justifiably proud of the successful results obtained through the application of this method, I feel that it is my duty to comment that the computer aspect of the work has not reached full development and is deserving of the financial support needed to increase its widest usefulness. At the present moment a routine to detect 'missing information' has not been commissioned. Due to the lack of documentation the use of the programmes is restricted since the format for the submission of data is known only to the authors. It is very unlikely that a profitable return on the development costs will be enjoyed before the programme is fully documented and made available to wider use. My criticism of the present incomplete state of the work is being voiced purely with the intent of focussing on the significance of this project and the fact that it is deserving of development on an industry basis. It should be noted that at the economical cost of R4.00 per sq ft of computer print-out, a mining engineer can hardly afford to miss the opportunity of using the programmes on other (e.g. metalliferous) mineral deposits of tabular formation. Since the publication of this paper I have had an opportunity to see the results of the programmes developed by Drs M. D. G. Salamon and F. Deist for designing bord and pillar workings. The basic data for these latter programmes are extracted from iso-line plans drawn conventionally by geologists, a task that could be considerably expedited through the use of Mr Hawkins' programmes. It appears that the efforts of these respective teams are complementary and it is in the interests of the industry that these individual components should eventually form part of an integrated system. E. Margo* (Member): This paper is a good example of how and where the backroom scientist-in this case the mathematical statistician-can aid the mining engineer to develop not only more accurate means for dealing with valuation problems but to develop a tool that can also cope with changed geological specifications.

Jan 1, 1969

By D. Yu. Paleev, O. Yu. Lukashov, A. Yu. Krainov, E. R. Shrager, I. M. Vasenin

The gas-dynamic method is presented of calculation of explosion-proof distances during an explosion of the methane-air mixture in mine working. On the basis of this method is modelled of shock waves interaction with explosion protective parachute partitions, obstructions and water barriers. Calculations have been carried out of attenuation factors of shock waves during their interaction with explosion protective structures, arranged near conjugation zones of mine workings. Possibilities have been analysed of suppression of intensity of shock waves and of propagation of shock waves control in mine working network of coal mines by installation of explosion protective structures.

Jan 1, 2003

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012