Search Documents

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By M. J. A. Leal-Gomes

There is a set of settled ideas in the field of the mechanics of rock mass joints, that need a deep revision, after the last experimental works of several authors. In this paper, this theme is approached under several viewpoints, like the following ones: the essential influence of the mating or mismatching of rock joints on their strength (different strength models are applicable to these two situations, one leading preferably to normal scale effects, and the other to inverse scale effects); Patton's model is a bad formulation of the joint strength, whenever there is a dilation effect in the slidings (actually, the essential consideration of the amplitude of the roughess isn't made by any limit equilibrium model, like Patton's model); the joint strength increases as the width perpendicular to the sliding direction is reduced (previous works of other authors suggested the independence of the strength on that width); the reduction of the anisotropy of the roughness, as the sample symmetry and sample dimensions increase; there is no scale effect in the discontinuity mechanics, if there is no roughness heterogeneity; when only the same roughness and undulation orders are involved in the tests, shorter samples have larger peak displacements and lower shear stiffnesses than larger samples (usually, the contrary is admitted). For all these reasons, there isn't an easy correlation between the small scale tests and the natural large joint scale. Only "in situ" large scale tests have some representativeness. All the above mentioned questions are correlated to each other. Es gibt eine Menge eingewurzelter Ideen im Gebiet der Mechanik von Felsklüften, die, nach den letzten experimentellen Arbeiten von mehreren Verfassern, eine tiefe Überprüfung benötigen. In dieser Mitteilung, wird dieses Thema unter mehreren Blickpunkten angegangen, wie die folgenden: der wesentliche Einfluß des Zusammenpassens oder nicht Zusammenpassens von Gesteinsklüften auf ihre Festigkeit (verschiedene Festigkeitsmodelle sind auf diese zwei Situationen anwendbar, eins, das vorzugsweise zu normalen Maßstabseffekten führt, und das andere, das zu umgekehrten Maßstabseffekten führt); Pattons Modell ist eine schlechte Formulierung der Kluftfestigkeit, immer wenn es einen Dilatationseffekt in den Verschiebungen gibt (in Wahrheit, wird die wesentliche Berücksichtigung der Rauheitsamplitude von keinem Grenzgleichgewichtsmodell beachtet, wie Pattons Modell); die Kluftfestigkeit wächst wenn sich die Breite senkrecht zur Verschiebungsrichtung verringert (frühere Arbeiten anderer Verfasser suggerierten die Unabhängigkeit der Festigkeit von jener Breite); die Verringerung der Rauheitsanisotropìe, wenn die Probekörpersymmetrie und Probekörperabmessungen zunehmen; es gibt keinen Maßstabseffekt auf die Trennflächenmechanik, wenn es keine Rauhheitsheterogenität gibt; wenn nur die gleichen Rauheits- und Ondulationsgrößenordnungen in den Versuchen verwickelt sind, haben kürzere Probekörper größere Spitzenverschiebungen und geringere Schersteifigkeiten als größere Probekörper (gewöhnlich, wird das Gegenteil angenommen). Wegen aller dieser Gründe, gibt es keine einfache Korrelation zwischen den Versuchen im kleinen Maßstab und dem natürlichen großen Kluftmaßstab. Nur "in situ" Versuche im großen Maßstab sind einigermaßen repräsentativ. Alle die oben erwähnten Fragen hängen miteinander zusammen. Il y a un ensemble de des bien établies arrière-pensées idées dans le champ de la mécanique des discontinuités en massifs rocheux qui ont besoin d'une profonde revision, après les derniers travaux de divers auteurs. Dans cet article cette matière est abordée sous divers points de vue, comme les suivants: la signification essentiel de l'ajustement ou du désajustement des discontinuités dans leur résistance. Des différents modèles sont applicables à ces deux situations, une conduisant de préference à des effets d'échelle normaux et l'autre à des effets d'échelle inverses; le modèle de Patton est une mauvaise formulation de la résistance des joints quand il y a effet dilatant dans les glissement. En effet la contribuition essentielle de l'amplitude de la rugosité n'est pas consideré par aucun modèle d'équilibre limite comme le modèle de Patton; la résistance des joints croit au fur et à mesure que la largueur perpendiculaire à la direction de glissement est réduite. Des travaux antérieurs d'autres auteurs suggéraient que la résistance était indépendant de cette largueur; la réduction de l'anisotropie de rugosité au fur et à mesure que la symétrie et les

Jan 1, 2003

By Y. H. Hatzor

ABSTRACT: A fully dynamic, two dimensional, stability analysis of a highly discontinuous rock slope is demonstrated in this paper. The studied rock slope is the upper terrace of King Herod’s Palace in Masada, situated on the western margins of the seismically active Dead Sea Rift. The dynamic deformation of the slope is calculated using a fully dynamic version of DDA in which time dependent acceleration is used as input. The analytically determined failure modes of critical keyblocks in the jointed rock slope are clearly predicted by DDA at the end of the dynamic calculation. It is found however that for realistic displacement estimates some amount of energy dissipation must be introduced into the otherwise fully elastic, un-damped, DDA formulation. Comparison of predicted damage with actual slope performance over historic time span window of 2000 years allows us to conclude that introduction of 2% kinetic damping should suffice for realistic damage predictions. This conclusion is in agreement with recent results of Tsesarsky, Hatzor and Sitar (2002) who compared displacements of a single block on an inclined plane subjected to dynamic loading obtained by DDA and by shaking table experiments. Using dynamic DDA it is shown that introduction of a simple rock bolting pattern completely stabilizes the slope. RÉSUMÉ : On présente dans cet article une analyse bidimensionnelle complète de la stabilité d’une pente rocheuse très fracturée. La pente rocheuse étudiée est la terrasse supérieure du Palais du roi Hérode à Massada, située sur la rive Ouest du Rift sismiquement actif de la Mer Morte. La pente est constituée de blocs de dolomite raide présentant une stratification sub-horizontale et des joints sub-verticaux. La déformation dynamique de la pente est calculée en utilisant une version entièrement dynamique de l’Analyse de Déformation Discontinue (DDA) où l’accélération dépendant du temps est utilisée comme donnée. Les modes de rupture déterminés analytiquement des blocs clés dans la pente rocheuse fracturée sont clairement prévus par l’approche DDA à la fin du calcul dynamique. On trouve cependant, que pour obtenir des estimations réalistes du déplacement, il faut introduire un facteur de dissipation énergétique sans lequel la formulation DDA serait totalement élastique et sans amortissement. En comparant l’endommagement prévu avec les caractéristiques de la pente sur une période historique de 2000 ans, nous pouvons conclure que l’introduction d’un amortissement cinématique de 2% suffit pour obtenir de prévisions réalistes. Cette conclusion est conforme aux résultats récents de Tsesarsky, Hatzor and Sitar (2002) qui ont comparé les déplacements d’un bloc isolé sur un plan incliné sous chargement dynamique obtenus avec l’analyse DDA et à partir d’essais sur table vibrante. ZUSAMMENFASSUNG: En utilisant une modélisation DDA dynamique on montre que l’introduction d’un système simple de boulonnage stabilise la pente.In dieser Veroeffentlichung wird eine vollstaendig dynamische, zweidimensionale Stabilitaetsanalyse eines hoechst diskontinuierlichen Steinhangs dargestellt. Der untersuchte Hang ist die obere Terrasse des Herodespalastes in Massada, welche in den westlichen Randgebieten des seismisch aktiven Toten Meer Grabens liegt.Die dynamische Deformation des Berghangs wird mit Hilfe einer vollstaendig dynamischen DDA-Version berechnet, in welcher als Input die zeitabhaengige Beschleunigung eingegeben wird. Die analytisch bestimmten Versagensarten kritischer Schluesselbloecke in diesem zerkluefteten Steinhang werden durch Anwendung von DDA am Ende der dynamischen Berechnung klar vorausgesagt. Es zeigt sich jedoch, dass fuer realistische Dislozierungs-Abschaetzungen ein gewisses Mass an Energieverlust in der sonst vollstaendig elastischen, ungedaempften DDA-Fassung einbezogen werden muss. Der Vergleich des vorhergesagten Schadens mit dem aktuellen Verhalten des Berghangs waehrend einer historischen Zeitspanne von 2000 Jahren erlaubt uns zu schliessen, dass ein Zusatz von 2% kinetischer Daempfung fuer eine realistische Vorhersage des Schadens ausreichen sollte. Diese Schlussfolgerung steht im Einvernehmen mit neuen Ergebnissen von Tsesarsky, Hatzor und Sitar (2002), welche die Dislozierung eines einzelnen Blocks auf geneigter Ebene unter dynamischer Belastung – unter Anwendung von DDA und “shaking table”-Versuchen – verglichen. Mit Hilfe der dynamischen DDA wird gezeigt, dass der Steinhang durch Anwendung einer einfachen Steinschraubenstruktur vollkommen stabilisiert werden kann.

Jan 1, 2003

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By P. J. Foster

A common theme running through recently introduced mining health and safety legislation in many parts of the world is risk assessment. Most recently, risk assessment legislation has been introduced across the mining industry of South Africa and the view that the introduction of risk assessment based legislation provides an ideal opportunity to improve on past health and safety performance is presented. Risk assessment techniques range from highly complex safety system techniques that are used in high technology process industries, to subjective techniques based on simple judgements that are finding use in many other industries. The objective of this paper is to shed some light on risk assessment, not by detailing the risk assessment process but by identifying the crucial elements that need to be considered if risk assessments are to be successful in changing health and safety performance. A case study is presented illustrating the introduction of risk assessment into the Ingwe Coal Corporation, one of South Africa?s largest mining houses, to indicate how the system was developed and how it is being used.

Jan 1, 1998

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

By A. More, J. M. Míguez, J. Bullón

In 2000 Ferroatlantica started a project with the aim to develop a new casting machine for silicon and other ferroalloys. Until now, it has been cast more than 25.000 tons of silicon for the chemical and metallurgical market. This system has improved the process yield, productivity and product quality which place?s Ferroatlantica at the top of technology development in this field. After the first presentation of the Ferroatlantica?s casting machine at Infacon X, we would like to show the improvements in the control which have permitted us to increase the lifetime of the copper and to obtain, at the end of the machine, the right product size for the customer avoiding the current necessity of crushing and sizing the lumpy metal. Furthermore, we have improved the system in relation to the obtaining of smaller granulometries at the end of casting machine. Not only is this kind of machine cost competitive for special silicon applications but also for other normal ferroalloys with different specifications of size and thickness.

Jan 1, 2007

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By H. Bhikha

The minerals industry is committed to the principles of sustain-ability. Reducing water consumption is a priority area, especially for regions of water scarcity. This paper presents a systemic optimization of the water balance of the Skorpion Zinc refinery with the aim of reducing water consumption. An Aspen Plus simulation of the process is used. The validity of the simulation is tested by measuring key output variables and comparing results to plant data. A number of water minimization scenarios are investigated, Including unit operation and circuit configuration changes. The scenarios leading to the largest reduction in water consumption are through the full recycle of treated effluent water, which results in water savings of up to 19%. Reducing process water and/or recycling of untreated water is prohibited by the build-up of trace elements, which affect product purity. The Skorpion process already features a highly optimized water balance, with unit operational changes merely resulting in a shift in the water balance. Consequently, the largest area for improvement is through the re-use of effluent water. Keywords Skorpion zinc water usage, process optimization, sustainability.

Jan 1, 2011

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

By A. N. Brown

This title of is not that originally chosen for the Colloquium, which was 'A high gold price'. Such a title would have been unfortunate because it would have related the Colloquium only to the high gold price of the past two years, which reached the dizzy peak of 850 dollars per ounce in January 1980. The chosen title is, of course, the right one because it places the whole problem in the right perspective. It relates to a situation that has occurred many times before. Over the course of the past century, the gold price has periodically been inhibited from rising, so that it has undergone a succession of stepwise increments. With each increase, the relationship of the working cost to the gold price alters, and gives rise to a jump in ore reserves. Award for CMI fuelling technique Consolidated Metallurgical Industries Limited - the Lydenburg-based ferrochromium producer in the J.C.I. group - was one of the five recipients of the 1981 National Productivity Institute annual award.

Jan 1, 1981

By T. N. Moore, E. M. De Souza

This paper details a study conducted in Canada on the use of a drill with two different types of elastomer-covered handles in place of the standard steel handles. One type of handle was covered with a relatively stiff elastomer with a durometer of 70 (referred to as the plastic handle), and the other was covered with a more compliant elastomer with a durometer of 56 (refered to as the rubber handle). It was found that, compared with the steel handle, the overall acceleration at the interface between the plastic handle and the drill operator's hand was 2,5 times less, and that between the rubber handle and his hand was 3 times less. This reduction occurred predominantly in the frequency range above 500 Hz, and was greater with increasing frequency. However, an analysis based on the methodology of an international standard (which places greater importance on low-frequency vibration), indicated that the reduction in vibration levels was minimal. ~he driller himself felt that operation with the plastic and rubber handles was more comfortable, the rubber handle being preferred.

Jan 1, 1991

By R. Heunis

The hazard of rock bursts and rock falls as experienced in South African gold mines is examined in the light of recent research findings. The problem areas include high fatality rates, losses in production and equipment, and a detrimental influence on the recruitment of labour. The nature of the hazard is analysed, and it is shown that rock bursts are strongly related to the spatial rate of energy release by mining but that rock falls are not. The role of blasting and geological discontinuities is discussed. Practical rock-burst control strategies are compared, including the use of stabilizing pillars, back-filling and, in particular, techniques for reducing the frequency and severity of accidents resulting from large rock bursts. The latest stope-support experiments and their potential implications to mining are consid~red. It is concluded that a better understanding of the rock-burst and rock-fall hazard has resulted from the industry's research efforts. The findings can be applied towards obtaining an improved underground environment for men and machines.

Jan 1, 1980

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988