Search Documents

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025

By R. J. Hundermark, L. R. Nelson

The critical importance of tap-hole design and management to furnace performance and longevity is explored through examining some of the specific matte, metal and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloys smelting and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally core aspects of tap-hole equipment and maintenance are identified that are considered important to securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance.

Jan 1, 2014

By B. P. Watson, D. Hoffmann, D. P. Roberts

Potholes on the Merensky and UG2 reefs in the Bushveld Complex occur as near-circular to elliptical depressions or slumps on the reef horizon, normally presenting as severe disruptions which prevent economic extraction. Within the pothole, the reef and other strata may either be attenuated, absent, or highly deformed, this being the result of the overlying hangingwall strata having slumped down. The hypotheses for pothole formation involve several mechanisms, including downward erosion, upward fluid movement, or synmagmatic deformation. When potholes are exposed in mine workings, significant fracturing is often observed. This fracturing is particularly evident in anorthosite rock types. Stress measurements were conducted in a pothole on the Merensky Reef to determine if the fracturing was due to high stress conditions. The paper describes the measurement results and numerical modelling that was done to determine the influence of depth and mining on the stress condition at the site. The results show that high stresses do exist in at least some potholes, and that current formation theories do not adequately explain the measured stresses. In support of understanding the high local stress associated with the pothole, the study explored several rock engineering modelling processes to validate the conditions of the study site and enclosing excavations. A better understanding of the stress conditions in potholes with additional data could lead to more appropriate support design and avoidance of potential rockbursts in these structures.

Jan 1, 2021

By M. Le Roux, Q. P. Campbell, N. Hughes

Water plays a significant role in minerals processing; this is especially true in coal preparation where water-based beneficiation is widely accepted and consistently delivering sharp separation efficiencies and high product yields. Although wet processing is favoured, the substantial process water requirement may prove this impractical and unsustainable in some parts of the world. Many coal-rich regions (including South Africa) have experienced severe water shortages. Coupled with the effects of drought, some countries experience freezing winters from which problems related to frozen process water and machinery may arise. Hence coal preparation practices will soon have to adapt, irrespective of the technical and economic feasibility offered by the currently employed water-based methods. As a result, extensive research into the development of dry methods for effectively beneficiating coal has progressed. This review paper intends to provide a collection of the relevant information pertaining to dry coal processing globally, and aid in understanding the applicability, performance, success or failure thereof. The methods available for dry materials preparation, with special regard to those applicable for coal beneficiation, are detailed in terms of principle, applicability, limitations and performance. Dry coal beneficiation has potential to aid the current wet-based methods with some considerations to possible limitations set forth by coal geology, application, product specification, particle size distribution, moisture, efficiency, capacity and cost. These methods may be established in future, especially in the arctic, arid and under-developed regions through new plant installations, expansions and small mines processing. Keywords: Dry coal processing, preparation, cleaning, beneficiation

Jan 1, 2020

Plurigaussian simulation allows constructing lithofacies or rock type models that reproduce the contacts between facies in accordance with the geologist?s interpretation. Its implementation requires inferring the local facies proportions, but the uncertainty in the true proportions is not accounted for. The simpler model with constant facies proportions may not yield realistic results, due to the possibility of obtaining facies at locations where it is geologically unlikely to find them. This article presents a variation of the plurigaussian model, in which the facies proportions are represented by random fields. The realizations can be made conditional to soft geological informati onto account for local changes in the facies proportions. The model is illustrated via a case study of a porphyry copper deposit where four Gaussian random fields are simulated conditionally to drill hole data and to constraints on the probability of finding a given facies at specific locations (control points) in the deposit. Then the first two fields are truncated using the random thresholds defined by the last two, generating a three-facies model. The proposed random proportion model proves to be simple to use and to account for spatial variations of the geological characteristics and for the uncertainty in the facies proportions. Keywords: categorical variable; lithofacies; truncated plurigaussian simulation; regionalized proportions

Jan 1, 2008

By C. Lottering

Copper sulphate solutions are produced during the pressure leaching of first-stage leach residue in a typical base metal refinery process. Apart from impurities such as selenium and tellurium, this leach solution also contains other precious metals (Rh, Ru, and it) due to dissolution in the pressure leaching stage. Selenium and tellurium are removed from the leach solution by precipitation with sulphurous acid, since these elements negatively affect electrowinning. This study investigates the feasibility of modifying the Se/Te precipitation process step to achieve significant rhodium precipitation in addition to selenium and tellurium precipitation, in order to reduce the rhodium inventory of the process. Thiourea, S02, formaldehyde, formic acid, and sodium thiosulphate were evaluated to determine which of these reagents would achieve the highest Rh precipitation. Based on these screening tests, SO2 and thiourea were selected to be used as precipitation reagents in optimization tests. During these optimization tests, the operating temperature (80 to 150°C) and the amount of reagent added (80 to 140 per cent excess) were varied to evaluate the effects that these operating conditions have on the precipitation behaviour of Rh as well as Se, Te, Cu, and Ni, and to propose appropriate operating conditions. It was found that thiourea resulted in good Rh and Se precipitation (typically in excess of 90 per cent), but precipitated noticeably more copper and nickel from the solution than when SO2 was used. In addition, thiourea had poor Te removal characteristics. SO2 achieved a maximum of 70 per cent precipitation of the rhodium. Faster kinetics and a larger extent of Te precipitation were, however, observed when using SO2 compared to thiourea.

Jan 1, 2012

By D. D. Munro

Finsch Mine is a Kimberlite diamond mine located at Lime Acres in the Northern Cape of South Africa. The mine was founded in 1961 and started surface-mining in 1964. Underground production commenced in 1990 using a Modified Blast Hole Open Stoping method for the mining of Blocks 1,2 and 3. Block 4 is currently being mined as a Block Cave. The process of identifying and optimizing a mining method to mine the Block 5 ore body started in 1991 and in 2006 Inclined Caving was identified as being a technically feasible method. This report aims to document the process employed in developing this method by the Block 5 Pre-Feasibility Team as well as discussing the technical challenges encountered during this process.

Jan 1, 2010

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

By R. Minango

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well-known and establishedprocess. As the process advances, Cu is extracted to the solvent and is replaced by H+in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually a relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: SX-1?standard extraction of Cu with oxime. The resulting raffinate contains about 6?8 g/lCu and 50 g/lH2SO4. SX-N?Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3etc. The extraction removes no metals, but decreases the concentration of acid from 50 to10 g/l. SX-2?Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100?150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility at Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX2, 2?3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with alamine-based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 and SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E2S for SX 2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions.

Jan 1, 2012

By N. Mutemeri, T. -L. Field, M. Chuma

The categorization of artisanal and small-scale mining has a significant impact on perception and understanding of the sector, particularly from a livelihood perspective. Several developing countries classify different types of artisanal and small-scale mining based on legal status. Given the nature such activities, the tragedy of the commons theory has been applied to understand the inevitable environmental, economic, sociocultural, safety, and health negative externalities – which are products of informality and illegality. Consequently, formalization is a panacea to sustainability. This article aims to offer a conceptual organization and foundational knowledge for characterization of artisanal and small-scale mining. It seeks to identify existing literature on the subject to avoid replication and acknowledge other scholars. Moreover, the article aims to place the study within the context of existing literature, establishing relationships with other studies and why the research is necessary. This paper pinpoints gaps left from other studies in so far as the characterization of artisanal and small-scale mining is concerned. Thus, reviewing literature abetted in finding similarities and differences on how artisanal and small-scale mining is defined from a scholarly and legal basis. The paper ascertains major claims made by earlier research on this topic, such as environmental impacts, the lack of adequate regulatory framework, and presents querying and probing questions lacking from other studies.

Jul 10, 2024

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By K. Thambi

The court in Baleni v Minister of Mineral Resources [2019] 2 SA 453 GP and [2020] 4 All SA 374 (GP), deliberated on the protection of rights of a community holding informal land tenure under Customary Law. The contention related to the necessary level of consent needed to acquire a mining right over such land. Moreover, whether consultations with such communities (Section 23, Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) or consent (Section 2, Interim Protection of Informal Land Rights Act, No. 31 of 1996 (IPILRA)) was required to acquire such right. The case has a significant bearing on the granting of mining rights in South Africa, and the discretion of the Minister of Mineral Resources (the Minister) in this regard. However, the objectives of the MPRDA and IPILRA do not dovetail, therefore consultation and consent are not mutually exclusive (Tlale, 2020). This note argues that, despite the resounding victory of this case, the peripheral basis surrounding the decision and the various levels of engagement require serious deliberation. Equally, the degree of reliance on the IPILRA requires clarity to avoid aborting the fundamental objectives of the MPRDA. This paper provides considerations and recommendations that may reduce or eliminate the tensions between the statutory and socio-economic rights in the application of the two statutes.

Sep 1, 2022

By A. Mabentsela

A furnace freeze lining is necessary for safety and economic reasons in several smelting operations. The integrity of the freeze lining is put at risk by furnace power imbalances. Although numerous models have been derived to model the growth and depletion of the freeze lining due to power imbalances, no model exists for thermomechanical damage to the freeze lining. This study provides an initial pathway for modelling thermomechanical damage to the freeze lining in an ilmenite smelting furnace using information from the literature and experimental work. A methodology under the framework of continuum damage mechanics is proposed to model mechanical damage to the freeze lining due to phase changes, thermophysical changes, and constrained thermal expansion. Drill cores of solidified slag ingots were used to represent the freeze lining. The modified power law proved to be the best predictor of the softening response of the drill cores. Damage driving parameters were extracted from the raw data, and governing equations of the parameters with respect to temperature were derived for use in a finite element method (FEM) code.

Jan 26, 2023