Search Documents

By E. L. Forner, G. M. Miller, J. Scheepers, A. J. du Toit

"The sizing, designing, and costing of copper electrowinning circuits requires an in-depth understanding of the fundamental relationships between circuit parameters and the practical operation requirements. The aim of this investigation was to optimize total copper electrowinning project cost by mapping the operating limits of key mechanical equipment. The model was compiled by mapping various cellhouse layouts in terms of number of cathodes per cell, crane productivity, stripping machine productivity, and rectifier–transformer (rectiformer) sizing using data tables for sensitivity analysis. These parameters were then collated and evaluated on a cost by size basis. The model provides an optimum band of operation for cellhouse productivity and project capital cost for a typical range of production throughputs, from 10 kt/a to 200 kt/a cathode copper. The information may be used as a high-level selection guide to assist with identifying a costeffective copper electrowinning circuit design for a specific production rate. The data was validated and compared with existing copper electrowinning cellhouses around the world that typically install no more than 84 cathodes per cell. IntroductionThe sizing, designing, and costing of copper electrowinning (EW) circuits require an indepth understanding of the fundamental parameters as well as the practical requirements to optimize cellhouse productivity and capital cost. Although a significant amount of work has been done designing new copper electrowinning circuits, an in-depth evaluation of world operating data reveals that the number of cathodes per cell, which affects cellhouse layout and productivity, is not consistent for a specific production rate (Anderson et al., 2009; Robinson et al., 2003, 2013). Based on this premise, Kafumbila (2017) suggested that there are unanswered questions, such as ‘why are the numbers of cathodes per cell different for copper production rates of 20 kt/a and 40 kt/a?’In this paper, data tables are employed to map the operating limits and costs of key Cu EW equipment. An overall Cu EW project cost map is then compiled by collating optimum cellhouse layout (number of cathodes per cell), optimum crane productivity, optimum"

Nov 1, 2018

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By D. R. Hack, N. M. Sirakov, M. L. Feves, M. Iwanowski

This paper presents a new approach capable of volume calculation of 3D reconstructed geological objects. The method is based on a well-known concept that states the volume of an object can be computed as the limit of the sum of the area of infinite number of sections, which cut the 3Dobject. Since shortage of input data about the geological objects usually exists, Mathematical Morphology and polynomial interpolation are employed to generate a set of intermediate sections between the set of initial sections. A Mathematical Morphology tool is applied to compute the area of the two of sets initial and generated 2D sections. Regularities together with Delaunay Triangulation are employed to perform 3D reconstruction. A formula is developed on purpose of volume calculation of the reconstructed objects. A set of ten theoretical, electrical resistivity cross-sections were generated and used to perform an experiment to show the capability of our approach to estimate the volume of complex 3D geological object in case of sparse 2D sections. The volume determined using the morphological approach presented in this paper show good correlation with the volume of the original input object. Advantages and disadvantages of our volume calculation approach are discussed in the conclusion of this paper. Keywords: electrical resistivity, sparse 2D sections, geological objects, smooth 3D visualization and volume calculation.

Jan 1, 2003

By D. Fray

Electrochemical processing using molten electrolytes is undergoing a considerable renaissance due to several innovative ideas being explored both in the laboratory and also at the pilot scale. Several of these new ideas are related to developments in energy generation and storage and involve solid electrolytes. Sodium has been prepared by the electrolysis of sodium carbonate or sodium hydroxide with the transfer of sodium ions through a sodium beta" alumina membrane and magnesium oxide dissociated by the removal of the oxygen through a stabilized zirconiaelectrolyte incorporating a fuel cell electrode. By using halides with highly electropositive cations, such as molten calcium chloride, it has been found that the favoured cathodic reaction, when oxygen is present, is the ionization of oxygen and not the deposition of calcium. This approach has been applied to the reduction of many metal oxides including titanium, zirconium, niobium and rare earth oxides and, by using a mixture of oxides as the cathode, homogeneous alloys are produced. This concept can also be applied to deoxidation of solid and liquid metals. Refining of metals is possible using intercalation compounds and, in a completely different application, it has-been found that, by intercalating alkali metals by electrolysis of alkali halides into graphite, it is possible to produce carbon nanotubes and nanoparticles. The technological opportunities of these various concepts will be discussed.

Jan 1, 2004

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

A Special General Meeting of the Institute was held in Kelvin House, Johannesburg on Wednesday, 29th September, 1971. The President, Prof. D. D. Howat opened the meeting at 9.55 a.m. The President read the notice of meeting which was as follows: "In order to bring industry into closer liaison with the work of your Institute and to place the Institute's finances on a sound basis your Council recommends that companies be admitted to membership of the Institute under clause 2.6 of the Constitution, that is, as Non-Corporate members. The designation for this class of member will be that of "Company Affiliate". 2 Membership: This clause to be amended as follows:- 2.6 "Non-Corporate members shall comprise the grades of:- Company Affiliate Honorary Fellow Graduate Associate Student" 2.6.1 This clause to be added:- "Companies involved in or associated with the mining or metallurgical industries are eligible to become company affiliates" 2.14 Add:- "A special certificate shall be issued to all company affiliates". After giving the background to the recommendation made by Council the President asked for a proposer and seconder for the resolution. Mr J. K. E. Douglas proposed and Mr D. G. Maxwell seconded the resolution. The meeting agreed that the constitution be amended as proposed. The meeting closed as 10.05 a.m.

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By S. Moodley

In the chloride process for Ti02 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100°C to yield gaseous metal chlorides. Although feedstock preference is largely based on Ti02 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlori¬nators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag). A common feature of the tests was that particles finer than 75 Km tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant (ki) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

By S. Moodley

In the chloride process for TiO2 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100ºC to yield gaseous metal chlorides. Although feedstock preference is largely based on TiO2 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlorinators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag).A common feature of the tests was that particles finer than 75 µm tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant ([ki]) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By M. Bailey-McEwan

The application of refrigeration on deep South African gold mines is mostly achieved through the medium of chilled water which is produced in central installations either on surface or underground. The amount of refrigeration has been increasing rapidly over recent years, and the total installed capacity on all gold mines now exceeds 1000 MW(R), with annual running costs exceeding R100 million for electricity alone. Hence, there are strong incentives to design such installations for optimal cost-effectiveness. The duty required of these installations varies considerably, owing to daily and seasonal climatic changes and the varying nature of the water demand. It has long been recognized that a computer program to predict installation performance as a whole under any given conditions would be highly desirable. An interactive computer program, CHILLER, is described which enables the user to build an installation, consisting of any configuration of cooling towers, water storage reservoirs and packaged water chilling machines. Externally-dictated conditions such as the weather and chilled water demand must be specified, and all quantities under control of the installation, including internal water flow rates and compressor capacity regulators, must be set. The time-varying performance of the installation can then be simulated. Examples are given of the application of the program in the design of a new installation, and in evaluating the effect of any modifications to existing installations.

Jan 1, 1987

By M Scott, J J. McEwan

Silver and silver alloys tarnish readily by the formation of tarnish on the surface when exposed to a wide range of sulphur-containing atmospheres. This tarnish is unsightly and undesirable and can be removed either with a silver polish or a chemical dip. Polishes are, however, not suitable for irregular and embossed surfaces such as on coins, medallions and jewellery items, because of uneven removal of the tarnish layer and excessive wear. Successful tarnish protection can be achieved by either storing the items away from the aggressive atmosphere or by coating/treating the exposed surfaces with a protective layer. Storage is feasible for collections but is not suitable for items that are handled or worn regularly, such as jewellery. A number of commercial coatings and treatments have been developed, but to date there has not been a systematic evaluation of tarnish protection. This paper details the performance of a range of generic coatings in an accelerated tarnish test. The degree of tarnish was evaluated by means of loss in reflectivity and change in colour. Four coatings/treatments improved the tarnish resistance of silver by more than tenfold. These include an organic lacquer, rhodium electroplating and an organic self-assembled monolayer (SAM) conversion coating. Research is continuing to optimise these coatings. Keywords: silver alloys, tarnish resistant coatings, silver polishes.

Jan 1, 2006

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By D. T. Williamson, B. P. Gilbertson

Satellite observation of mine-dump vegetation by B. P. GILBERTSON, M.Sc. (Phys.) (Visitor) and D. T. WILLlAMSON, B.A., LLB., B.A. Hons. (Visitor) NASA's first Earth Resources Technology Satellite (ERTS-I) was launched on 23rd July, 1972, and has subsequently gathered multispectral imagery of most of Southern Africa from an orbital altitude of 900 km. Images of the Witwaters rand area have been studied in an attempt to differentiate between mine dumps having varying degrees of vegetative cover. At this stage it is clear that the various mine dumps can be located and identified, and differences in vegetative cover can be seen and measured. Patterns of vegetative growth, some characteristic to particular dumps, can also be seen.

Jan 2, 1974