Search Documents

By M. Khodadazadeh, K. G. van den Boogaart, T. Leißner, L. Tusa, J. Gutzmer, R. Gloaguen, M. Kern

Ore sorting is a technology that is increasingly used to process primary raw materials. Timeconsuming and expensive empirical state-of-the-art test work is carried out to assess whether the use of ore sorting for the enrichment of a particular ore makes technical and economic sense. With the innovative simulation-based approach presented here, it is possible to direct the selection of a suitable sensor based on quantitative mineralogical and textural data, thus avoiding much of the empirical studies. Required data can be collected quickly and cost-effectively using available methods of automated mineralogy. The obtained parameters such as mineral grain size distribution, modal mineralogy, mineral area and mineral density distribution have been utilised in this study to simulate the prospects of success of ore sorting, applying different types of sensors. Empirical tests with commercially available sensor systems have been conducted to experimentally validate the predictions of the simulations. The estimation of the target mineral grade can be further optimised by the use of machine learning algorithms for the integration of automated mineralogy data and sensor data. The approach can easily be adapted to other types of raw materials and thus has great potential to become a key technology for the optimisation of processing experiments. Keywords: Automated mineralogy, hyperspectral imaging, machine learning, ore sorting

Jan 1, 2020

By N. Kornelius

In recent years there has been an increased focus on corporate governance matters worldwide. The duties and responsibilities of directors of companies have come under close scrutiny, with shareholders increasing their demands for greater responsibility and accountability. Media attention and pressure groups have also had their effect. Governmental actions have supported these demands and directors have witnessed sweeping legislative changes imposing more onerous duties and liabilities than formerly imposed upon them at common law and in terms of the Companies Act. At the same time, the power of regulatory bodies has been increased to enforce this legislation and make someone pay to remedy an alleged infringement. Breach of such duties may incur personal or criminal liability, or both. Environmental protection legislation has become a particularly prevalent feature in this regard, and the number and complexity of statutes concerning the environment have increased over the past few years. Directors of South African companies will be familiar with relevant acts such as the National Environmental Management Act 107 of 1998; Conservation of Agricultural Resources Act 43 of 1983;Hazardous Substances Act 15 of 1973, as well as the National Water Act 36 of 1998. Now the directors of mining companies are faced with the Mineral and Petroleum Resources Development Act 28 of 2002.

Jan 1, 2003

By A. F. Khan

The CSense advanced process control (APC) solution?s main objective was to improve the stability of the pH in the first stage leach process thereby improving nickel and iron extraction efficiencies and reducing the base metal (BM) content in the platinum group metals (PGM) concentrate. By improving the stability of the control of the pH on the first stage leach it had the corresponding effect of improving the Ni extraction efficiency by 0.5% and the Fe extraction efficiency by 3.3%. The system relieved the operators of many decisions that were virtually impossible to make given the complex, variable and real-time nature of the processes in their charge. On the operational side, the operators understand the APC system and they trust it. Another benefit is the reduction in pH peaks in the autoclave, which can oxidize certain elements whereby they become difficult, if not impossible, to leach. These elements go right through the process and end up contaminating the PGM solids, with the result that the entire batch has to be recycled through a lengthy and costly processing pipeline.

Jan 1, 2009

By B. B. Mamba, J Ndalamo

The existence of an impressive reserve of oxidized cobalt-copper bearing ores in the African copper belt area lead the GECAMINES (DRC) to develop specific and adapted mineral processing routes (Mulaba-Bafubiandi, 2001). During the conventional diluted sulphuric acid leaching of oxidized cobalt-copper bearing ores commonly referred to as ?heterogenite?, more than 10% cobalt dissolution yield increase was observed in a plant situation (Mwema et al., 2002) when SO2(g) was flushed into the acidified cobalt leaching solution. The present paper attempts to elucidate mechanisms involved which lead to the increase of total cobalt as SO2 is flushed during the leaching of oxidized cobalt bearing minerals. The kinetics of cobalt dissolution as SO2 is flushed into the acidic solution as well as a full characterization, using UV-Visible spectroscopy, of Co2+ and Co3+ species present in the collected leachate are presented while possible effects of the presence of Cu and Fe on the leachability of cobalt bearing minerals present in the oxidised ore will be discussed. In the view of speeding up the leaching process, the mixed cobalt-copper oxidised ores were microwaves pre-processed. Preliminary results were also discussed.

Jan 1, 2007

By A. K. Verma

Several longwall faces in India have collapsed due to adverse geological conditions and/or inadequate capacity of powered supports. Thus it is imperative to access the capacity of a powered support and its interaction at longwall faces of varying geomining conditions in advance with lots of confidence. To achieve this, an index has been developed to ascertain the front leg pressure (FLP) of chock-shield support and roof-to-floor convergence (RFC) at longwall faces. The index called ?Longwall Face Stability Index? (LFSI) has been developed using statistics and Finite Element Modelling (FEM). The front leg pressure (FLP) and roof-to-floor convergence (RFC) predicted from the LFSI are validated with the field monitored data from two longwall panels. In this study, an attempt is also made to incorporate various geomining conditions into the finite element models typical of longwall mining practice. The index has taken into account the wide variations of geomining parameters like thickness, young?s modulus and friction angle of main roof (small, large), coal type (soft, hard), powered support capacity, and depth of coal seam. Thus, LFSI can be thought of as an index representing combined effect of roof type, geomining conditions and powered support capacity.

Jan 1, 2008

By N. Gibson

The application of oxygen in a copper smelter by N. GIBSON* (Visitor) This paper describes how the problem of increasing the capacity of the Rokana copper smelter was handled, and how oxygen was found to be technically and economically the best solution. The first phase of its implementation is outlined.

Jan 3, 1974

By S. W. Jacobsz, F. O. Abimaje

Internal stability is a key consideration in the design and long-term performance of granular filters, as it precludes particle migration and internal erosion. This study evaluates the internal stability of coal discard material in coal co-disposal facilities. Reusing coal discards could reduce mine waste volumes and mitigate associated environmental impacts. However, coal discard material differs from most soils in terms of particle strength and density, with possible implications for hydraulic stability. Laboratory seepage tests were conducted on coal discard material under varying void ratios, subjected to a range of hydraulic gradients, and the results were used to confirm the applicability of the widely used empirical Kenney and Lau filter criterion to coal discard. Findings revealed that particle loss increased with higher void ratios. Nonetheless, particle migration remained minimal, with a maximum particle loss of only 0.2%, suggesting that coal discard exhibits sound internal stability under the tested conditions.

Jul 3, 2026

By C. Birch

"Mineral reserve statements as well as optimizing mine planning require a block model with grades for each mining block. A cut-off grade is determined by considering the mining costs as well as the expected revenue for each block. These grades are estimated using various techniques, but in reality there is uncertainty in the grade values. These uncertainties result in two types of error. A type I error is where material is classified as ore and mined, but the true value is below the cut-off grade and the material is therefore waste. This material constitutes dilution. The type II error is where material is estimated to be below the cut-off grade and is classified as waste, whereas the true grade is actually above the cut-off grade. This material is not mined and the value is lost.This research considers the value of the lost ore and the costs of dilution under various degrees of uncertainty. Simulation using @Risk and mixed integer linear programing (Excel Solver) is used in a financial optimizer model to maximize either profit or net present value. This is applied to four Witwatersrand tabular gold deposits to investigate the impact of block grade uncertainty on cut-off grades.When optimizing for profit, value may be added by adjusting the cutoff grade slightly downwards. When optimizing for NPV, value may be added by lowering the cut-off grade significantly for the lower discounting rates. At higher discount rates, the lowering of the cut-off grades should be reduced, and in some cases an increase in cut-off grade may be required. Each mine reacted differently to the optimization and thus there is no single rule that can be applied across all tabular Witwatersrand gold deposits."

Jan 1, 2017

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

By Y. Zhan1, T. Moodley, M. A. H. Zahid

Mining operations are under growing pressure to improve safety and efficiency while dealing with aging infrastructure, complex processes, and workforce constraints. Although many sites are equipped with surveillance cameras and control systems, critical events often go unmonitored or under-analysed due to the lack of intelligent interpretation tools. Cameras typically act as passive recorders, requiring manual review by control room operators; a process that is labour-intensive, error-prone, and reactive. Vision AI is emerging as a transformative solution, combining computer vision and artificial intelligence to deliver real-time, actionable insights. This technology has evolved along two key phases: traditional object detection, and more recently, multimodal large language model integration. This paper presents solution architectures, deployment results, and key insights from real-world implementations across underground operations, open-pit truck-shovel operations, and smelter operations, demonstrating how Vision AI is reshaping mining operations to become safer, more efficient, and more intelligent.

Mar 6, 2026

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By J. Madias, E. Benavidez, E. Brandaleze, L. Castella

Knowledge of the physical and chemical properties as well as the behaviour of the mould fluxes during melting, important in order to improve continuous casting operations. Lubrication and control of heat transfer in the mould are the more relevant functions of these materials. Values of physical properties like viscosity and surface tension at melting range temperatures are required, as much as the thermal behaviour under process conditions. The heat extraction from the liquid steel has an important effect in the final quality of products. Mould fluxes are constituted by different oxides, and may form glasses and crystal phases during cooling. The solidification rate and the chemical composition determine the proportion, type and crystalline morphology, which are responsible of the thermal transfer processes. In this paper, viscosity values are reported in the melting range temperatures calculated by means of the Riboud model and compared with fluidity results obtained by the inclined plane technique. Also the linear expansion of the mould fluxes at high temperatures was determined by dilatometry. The crystallization in two different fluxes was determined by DTA tests and correlated with the basicity index. Crystal phases were evaluated by scanning electronic microscopy on quenched samples at 1300°C. This information is relevant to increase the knowledge on the peritectic steel grades casting process in order to improve its quality. Keywords: mould fluxes, heat transfer, crystal phases, peritectic steels, thermal properties.

Jan 1, 2004

By P. C. Schutte

There have been several high-profile accidents in the South African mining industry where fatigue was identified as either causal or contributory. The risk of fatigue is inherent in any work-time arrangement involving shift work and work that is physically or mentally demanding, repetitive, or requires high vigilance. The management of fatigue is not simply a matter of correct shift scheduling. Amore comprehensive approach is needed. In order to be successful, a fatigue management programme should address the unique needs of the operation in which it will be implemented and should be integrated into normal operations. Fatigue management is a shared responsibility between the organization and its employees, and all stakeholders should participate in order to provide the safest and healthiest working environment possible.

Jan 1, 2010

By M. Wang, Z. Sui, T. Lou

After smelting, the associated mineral ore accompanying Valuable Metal Compounds (VMC),such as titania and borate in BF., most of the VMC were separated from the metal into the molten slag that is an associated slags. Based on several case studies in laboratories and in a practice in a pilot plant on the associated slags , there occur a feasibility to recovery VMC from the slags by anew process- Selective Precipitation Technique (SPT) on which three continuous steps are involved: (1) The selective enriching the dispersed VMC into a designed mineral phase in the molten slag; (2) The selective coarsening the designed mineral phase with large crystal grain size;(3) The selective separating the coarsen phase from tailing by mineral dressing or hydrometallurgical process . Some results on the recovering the VMC from the associated slags by SPT were summarized as examples in present paper. Keywords: selective precipitation technique, associated slag, recovering metals from slag.

Jan 1, 2004

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By André de Jager, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge. The mine has installed a technologically advanced seismic monitoring system with monitoring sensors positioned at various locations and depths throughout the pit. The electronic data recording system records all relevant information on a continuous basis with early warning signals in cases of potential danger. From the information recorded by this micro-seismic system it was established that the energy release into the high-wall is predominantly influenced by the mining rate, water content and mining tempo and to a lesser extent by the blasting operations. To limit the negative effects of blast vibrations, the use of Electronic Delay Detonators (EDDs) was introduced. The optimal delays were determined through signature trace analysis. The vibrations obtained during blasts initiated by means of electronic delay detonators were monitored and compared to those traditionally obtained when standard pyrotechnic delay detonators had been used. The measured vibration data indicated an improvement of 25% to 100% drop in vibration amplitude compared. The accuracy and programmability of EDDs presented huge potential for blast optimization in terms of limiting the vibrations without compromising fragmentation. The whole project was conducted over a twelve week period with some 4000 EDDs. The average size of a blast was in the order of 350 holes using about 40kg explosives per hole, which equates to 14,000 kg explosives over 12 different blasts. The paper deals in detail with the blast optimization process with regard to: - determining the rock response time; - establishing the signature traces; - analyzing the wave interference patterns; - predicting the direction of constructive and destructive wave interferences; - optimizing of the inter-hole and inter-row delay periods; - measuring the ground vibrations. The results obtained during electronic blasting are compared to those obtained during pyrotechnic blasting. Comparisons are being made with regard to the following: - ground vibration measurements; - pit wall stability measurements; - blast safety.

Jan 1, 2006