Search Documents

By B. K. Loveday

There are certain ores that can be treated without upgrading (e.g., gold and uranium ores), and upgrading needs to be considered only for fairly low-grade ores of this type. If the grade is very low, treatment will not be economic even with upgrading, and there is therefore a limited range of ore grades for which upgrading is suitable.

Jan 1, 1980

By Z. Szczepanik, D. Milne, K. Kostakis

Abstract This paper presents the results of a series of creep tests performed on a total of nine samples of Lac du Bonnet granite from the Underground Research Laboratory near Pinawa, Canada. Each of the nine samples were subjected to stresses in excess of 80% of the average uniaxial compressive strength of the granite and were maintained at that level of constant loading for periods of time ranging between a few minutes and several months. Acoustic emission was recorded in order to monitor the development and accumulation of brittle microfracture damage in the samples throughout the long-term loading. According to previously published theoretical predictions and field results, as well as similar experimental results of creep tests in granite, samples should fail when loaded to 70% of their UCS for an extended period of time. Six of the samples did not fail when subjected to stresses in excess of 80% of their UCS over periods of several months and were subsequently subjected to uniaxial compression to failure. The average strength of the samples that had previously been subjected to long-term loading were comparable to the average published strength of this rock. Three of the nine samples had increased end confinement and these three samples failed under long term loading. Résumé Cet article présente les résultats d'une série d'essais de fluage de roche exécutés sur neuf échantillons de granite de Lac du Bonnet, du laboratoire souterrain de recherches près de Pinawa, Canada. Chacun des neuf échantillons a été alors soumis aux charges au-dessus de 80% de la résistance à la UCS moyenne du granit et a été maintenu à ce niveau du chargement constant pendant des périodes s'étendant entre quelques minutes et plusieurs mois. L'émission acoustique a été enregistrée pendant les essais afin d'obtenir des indications des dommages pendant le chargement à long terme. Selon des résultats théoriques précédemment édités et les résultats expérimentaux semblables des essais à long terme en granite, échantillons devrait échouer si chargé à 70% de leur UCS pendant une période prolongée. Six des échantillons n'ont pas cassé quant ils ont été soumis aux charges au-dessus de 80% de leur UCS et ont été plus tard soumis à la compression uniaxiale à la rupture. La force moyenne des échantillons qui avaient été précédemment soumis au chargement à long terme étaient comparable à la force éditée moyenne de cette roche. Trois des neuf échantillons avaient augmenté le confinement de fin et ces trois échantillons ont cassé sous le chargement à long terme. Zusammenfassung Dieser Artikel beschreibt die Resultate von Kriechversuchen, die an neun Proben aus dem Lac du Bonnet Granit des "Underground Research Laboratory" bei Pinawa in Kanada durchgeführt wurden. Jede der neun Proben wurde Drücken unterworfen, die mehr als 80% der einaxialen Druckfestigkeit des Granites entsprechen. Diese Drücke wurden für verschiedene Zeitspannen von wenigen Minuten bis zu einigen Monaten auf einem konstanten Niveau gehalten. Während der gesamten Langzeitbelastung wurden akustische Emissionen aufgezeichnet, um die Entwicklung und gesamthafte Beschädigung der Proben durch Sprödbruch aufzuzeichnen. Entsprechend bisher veröffentlichter theoretischer Vorhersagen, Feldversuchen und auch experimentellen Resultaten von Kriechversuchen an Granitproben wäre ein Versagen der Proben zu erwarten gewesen, wenn sie über längere Zeit einer Last von 70% ihrer einaxialen Druckfestigkeit unterworfen werden. Wider Erwarten trat bei sechs der Proben kein Versagen ein, als sie mit über 80% ihrer einaxialen Druckfestigkeit über mehrere Monate belastet wurden; daher wurden sie im Anschluss bei einaxialer Kompression zum Versagen gebracht. Die mittleren Festigkeiten der im Langzeittest verwendeten Proben sind vergleichbar mit den normalerweise für diesen Gesteinstyp angegebenen Festigkeiten. Drei der neun Proben versagten unter der Langzeitbelastung; diese drei Proben hatten eine erhöhte Endflächenreibung.

Jan 1, 2003

By J. A. L. Napier, J. S. Kuijpers

SYNOPSIS This paper demonstrates that the horizontal stresses induced by the creation of a tabular scope in a single mining step are always tensile at the centre of the stope span, but that compressive stresses are actively generated in hangingwalls and footwalls during sequential mining. A stress-distribution mechanism is introduced, and is used to explain the results for elastic behaviour, and for inelastic behaviour both during a single mining step and during multiple mining steps.

Jan 1, 1991

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By M. G. Spengler

A new type of pack has been developed primarily for the support of narrow stopes. It was shown in the laboratory that it has characteristics that very closely approximate the optimum required by underground support to achieve hangingwall stability.

Jan 1, 1978

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By D. W. Horsfall

This paper reviews the properties and uses of mixtures of coal with fuel oil, methanol, or water, emphasis being placed on mixtures of coal and water. The material presented is taken from studies conducted overseas, and it is recommended that similar studies should be conducted on mixtures containing South African coals, which differ from the coals of the northern hemisphere

Jan 1, 1990

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By R. S. Sarracino, M. J. Louw, S. M. Vather

Two detonation models, IDeX for ideal VOD and CPeX for non-ideal VOD, were used to predict the velocities of detonation (VOD) of five explosives: ANFO, a bulk emulsion, and three repumpable emulsions (R100 Gold, R100 Diamond, and R105). The theoretical VODs were compared with the in-hole VODs of the explosives, and the predicted and actual values were found to be within experimental error for ANFO and the bulk emulsion. The results were not consistent for the repumpable emulsions. The discrepancies can be explained as being due to variations in mining and loading practices. The results show that the detonation models can be effective tools in predicting the behaviour of explosives in different diameters and rock confinements, provided that the user is aware of the factors that can affect the optimal usage of explosives and equipment.

Jan 1, 1993

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By L. C. Woollacott

A computer-aid is described that is designed to calculate steady-state material balances for ore-dressing circuits. The program determines the material balance from a specification of the process condition. No mathematical models or data adjustment techniques are employed. As such the program complements existing simulation and material balance 'smoothing' packages. The process condition is specified using performance indicators. These are significant parameters in the industry with which all practising mineral processors are very familiar. The program employs an equation-oriented technique for material balancing and so has had to deal with the difficulties peculiar to that approach.

Jan 1, 1987

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By H. J. Swanepoel, N. B. Strydom

Groups of up to twelve new recruits to the industry were subjected to climatic room acclimatization for either five, seven, eight or nine days prior to being tested for the degree to which they had been acclimatized. These tests were done at 32,2 0C (wet bulb) at a wind velocity of about 0,4 m/sec and the men worked for four hours at a rate of 215,6 kg m/min on one day and at a rate of 431,2 kg m/min on the second day. The results indicated that there is no significant difference between the degrees of acclimatization obtained by the eight- and nineday procedures which confirms the conculsions drawn in a previous report1. The eight-day procedure can thus be claimed to be perfectly adequate and safe. Decreasing the period of exposure to five or seven days would however, not be justified because of the significant differences in physiological responses that were observed on both test days between men acclimatized for these periods and those acclimatized for nine days. It is concluded that it would be unsafe to employ these shorter periods of acclimatization when underground environmental temperatures at which the men are to work, exceed 31 0C (wet bulb).

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995