Search Documents

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By I. Nolet

Matte tapping is one of the most critical operations of a matte smelter. Every smelter has developed particular matte tapping practices and tap-hole repair strategies that are often based on the experience of the smelter personnel. As a result, very little information has been published on these critical topics. This paper aims at providing the information gathered from a survey conducted in the PGM and Ni industries on matte tapping practices and tap-hole maintenance strategies for different PGM-Ni matte smelting operations.

Jan 1, 2014

By R. G. B. Pickering

Conventional mining is an excellent match of mining method and equipment. The result is guaranteed performance. Change in the form of different technology requires change in mining method until the best match is achieved. This paper covers the development of technology and mining method that has occurred in the last five years to arrive at the objective of successful mechanized mining in narrow reef platinum deposits of the Bushveld Complex.

Jan 1, 2004

By E. Y. Baafi, H. Fan, W. Zeng

We present a discrete event simulator, TSJSim (Truck-Shovel JaamSim Simulator), for evaluating the stochastic and dynamic operational variables in a truck-shovel system. TSJSim offers four truck allocation strategies: Fixed truck assignment (FTA), Minimizing shovel production requirement (MSPR), Minimizing truck waiting time (MTWT), and Minimizing truck semi-cycle time (MTSCT) including the genetic algorithm (GA) optimization and the frozen dispatching algorithm (FDA) optimization rules. Multiple decision points along the haul routes for all the trucks close to the decision points were included in the model. The simulation results indicate that the trends associated with production tons and queuing time utilizing the four truck allocation strategies (MSPR, MTWT, FDA, and GA) all demonstrated similar patterns as the fleet size varied. As the system fleet size increased, the system production tons under these strategies at first increased significantly and then remained relatively constant; the queuing time relating to these strategies showed a positive relationship with the system fleet size. The bunching time decreased when the truck allocation strategies were applied in the model. In the simulated truck-shovel network system with multiple traffic intersections, by assigning the trucks at the intersections, both productivity and fleet utilization increased.

Dec 13, 2022

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

"Chairman: Dr R. E. ROBINSON Rapporteur: Dr R. P. COLBORNPapers:The simulation of crushing plants by W. J. WhitenSimulation of multi-component flotation plants by B. K. Loveday and G. R. MarchantComputer control of flotation at the Ecstall concentrator by M. P. Amsden C. Chapman and M. G. ReadingModel for the design and control of flotation plants by R. P. KingIn presenting his paper Dr W. J. Whiten outlined the basic concepts on which the control model was based and emphasized the fact that empirical models based as much as possible on theory were used to simulate each unit of the crushing plant. The final parameters of each model were computed using data collected from the plant. Unfortunately, the system did not permit accurate extrapolation but was successful when operating in the region from which the parameters were calculated.He concluded from the results of the test work that the crusher amperage was a critical parameter and that the utilization of the model gave a 15 per cent increase in the plant output. This was because the model predicted that a marginally fine grind would provide a significant increase in throughput. Dr Whiten elaborated on what constituted the multiple spline regression, explaining that it was a least-squares curve-fitting technique in one or more dimensions, where the calculation of coefficients in analytic expressions was replaced by the calculation of typical points on a very smooth curve called a spline function. The emphasis was placed on the shape and value of the curve or curves instead of on the coefficients as in analytic regression. A spline function was the line drawn between all points constituting the data set.Dr B. K. Loveday commented that the simulation was unusual in that the optimum throughput was considered to be the maximum throughput, which, surely, was limited by the crusher size. He also emphasized the importance of the interaction between both crushing and grinding circuits and added that in practice the optimum operating conditions were inter-dependent. Dr Whiten replied that in the case of the plant under consideration, the crushing process was not, in fact, the limiting operation.Mr C. E. Clifford indicated that the model was being used to simulate a number of crushing and grinding circuits at Mount Isa Mines. He reported that the model simulated the circuit satisfactorily for primary and secondary gap settings of 0,625 in. to 0,375 in., but that adjustment had to be made to the model parameters for gap settings of 0,250 in. to 0,125 in.In reply to a question from Dr D. M. Hawkins, Dr Whiten said that he preferred to use low-order splines with smaller segments rather than high-order spline functions with large segments."

Jan 1, 2014

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

By R. H. C. Andrew

With the advent in recent years qf mechanization in deep-level gold and platinum mines, large quantities of rubber was are being used on both production and support vehicles. Conditions in these types of mines are extremely harsh and, as a result, we performance is significantly lower than in other types of mining such as open-cast base metal mining, where more favourable conditions prevail. Various options are available to the user to reduce tyre costs, including the use of retreads, the filing of tyres, and the repair of damaged tyres. While these methods may be generally successful in open-cast conditions, their use in deep-level mining needs to be carefully evaluated for each particular set of conditions. A basic requirement for any evaluation of we costs is the availability of reliable data on tyre performance and, for this reason, it is essential that proper tyre records are maintained This paper reviews the performance of tyres in deep-level gold and platinum mines in Johannesburg Consolidated Investment Company, Limited (JCI) over a period of about 8 years, and shows how the costs of retreading and tyre filing can be evaluated in practice. It also discusses the cost implications of repairing damaged tyres.

Jan 1, 1994

By B. Kenny

The aim of this paper is to provide an overview of existing forms of subcontracting in the South African mining industry. A descriptive framework is developed to understand different subcontracting arrangements. We argue that, in order to do so, it is important to distinguish between labour broking and gang subcontracting. Data resulting from a research project (including an analysis of historical sources, interviews with contractors and focus group interviews with mineworkers) is presented to highlight the implications of changing formations of subcontracting for the South African mining industry in the late 1990s. Apart from the subcontracting of ?traditional? functions, such as shaft sinking, access development, catering and hostel maintenance, contractors are now used in ?core? mining activities. In some instances, whole shafts are ?outsourced? to outside agencies. It is argued that certain of the subcontracting arrangements have serious implications for the ability of the mining industry to improve health and safety standards. Some of the practices can potentially result in conflict between different categories of workers, and, as a result, instability in the industry.

Jan 1, 1999

R. C. J. Goode (President): South Africa is known for its sunshine and mineral deposits-especially its gold and its diamonds-and as this year marks the 75th Anniversary of the establishment of the South African Institute of Mining and Metallurgy, it is appropriate that I say a few words about mining and metallurgy and the part this industry and our Institute has played in the life of this country. Africa, as the Dark Continent, with its fascinating tales of Prester John, Ophir, Queen of Sheba and its myths and legends has throughout the ages fired the public imagination. Pharaoh Necho, 600 years before the birth of Christ, sent an expedition from Egypt around the Cape to probe this strange land. The gold for King Solomon's throne was said to come from Monomotapa-the country now known as Rhodesia. Centuries later the Arabs and Portuguese searched for this mineral wealth. The Arabs found little gold but unfortunately established a lucrative trade in black slaves. Now let us take a brief look into the closing stages of the Stone Age when the indigenous population of the lower portion of this continent consisted of the Bushmen, a nomadic hunting people who knew no metals and kept no stock, and the Hottentots who were a pastoral folk with cattle and sheep. Then somewhere about the 11th century the Bantu started their long migration southwards and brought with them the knowledge of smelting of iron ore. One of their settlements was here in Johannesburg on the Melville Kopje at Emmarentia. These people were the first miners and metallurgists on the Witwatersrand and the beautifully preserved iron smelting furnace constructed nearly 1,000 years ago is a tribute to their technical ability. This ability to use iron to make better spears for hunting or to fashion hoes for cultivating the soil led to their establishment as a superior tribe. The earlier Bushmen were pushed back to the inhospitable swamps and deserts and the Hottentots fled to the south. The Bantu also knew the art of copper smelting. In the days of the Dutch East India Company, at the end of the seventeenth century, Bantu workers brought copper from the north-west Cape to Simon van der Stel, but it was another two hundred years before the white man turned this to advantage. Stories of the Bantu mining gold spurred the early European hunters to travel deeper into the heart of Africa in search of wealth, and we are told that Karel Kruger, in 1834 whilst leading an ivory hunting expedition, discovered gold on the Witwatersrand, and took samples to Cape Town; but when he returned with a larger expedition a few years later his party was attacked by Moselekatze's Matabele near Potchefstroom. Kruger was killed and only the legend survived. The real spur to mining in this country was the discovery of diamonds in Griqualand West in 1867. The field seemed fabulously rich and diggers flocked to the scene from the four corners of the earth. With them came Cecil Rhodes, Barnato, Beit and some of the finest mining and financial brains the country had yet seen. These giant entrepreneurs were not tempted by the small deposits of gold in the Barberton and Pilgrim's Rest areas when these were made a few years later but

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it.

Jan 1, 2001

By D. F. Malan, W. J. Theron

Practical mining aspects should be considered when conducting pillar designs for bord-and-pillar layouts. The current methodology for pillar design will result in increasing pillar sizes with depth. This affects the extraction ratio and will result in onerous ventilation requirements when cutting large pillars. A holistic approach, including all mining engineering requirements, is required to ensure that the rock engineering designs are optimized to ensure efficient mining operations and sustainable production. Bord widths should not only be a function of the rock mass ratings, but should also be selected to fit the specifications of the mechanized equipment. The use of a ‘squat pillar’ formula for hard rock is discussed in the paper and the formula based on the exponents of the Hedley and Grant pillar formula, is explored. The effect of abutments and geological losses on average pillar stress is also explored. These factors must be considered when designing layouts at increasing depths.

Nov 27, 2024

By R. J. Durheim

Detailed investigations have been conducted into 21 rockbursts which caused damage to excavations in deep South African gold mines, in many instances resulting in the death or serious injury of workers. The objective of this study is to determine the principal factors controlling the severity and distribution of damage, so that strategies to reduce the hazard of rockbursts may be developed. It was found that the source mechanism is often controlled by the mine layout, and regional structures such as faults and dykes; while local rock conditions and support systems strongly influence the location and severity of damage. In the short term the most important lever for reducing the rockburst hazard is the effective implementation of existing rock engineering knowledge and technology.

Jan 1, 1998

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By S. M. Rupprecht

A deposit to be mined by underground methods can be accessed by a number of methods: ? Adit ? Decline or ramp ? Inclined shaft ? Vertical shaft. Adits are an economical approach when the orebody is above the general floor elevation i.e. suitable in hilly or mountainous terrain. Incline shafts are limited to relatively shallow deposits, and because they are developed on an incline, development lengths for a given depth are the three to five times longer than for a vertical shaft. Vertical shafts are the preferred method for deposits deeper than 300 m but the development rate is slow and construction costs are very high. Declines or ramps offer early access to shallow deposits, which develops the ore body expediently, but are generally developed at a gradient of approximately 12 per cent. Decline haulages have become an attractive alternative to shaft hoisting, and over recent years the role of decline access has become more widespread throughout South Africa. Traditionally, South Africa has enjoyed the use of shaft systems, largely due to the large knowledge base of mining the Witwatersrand Basin, where vertical and inclined shafts were the norm. South Africa has also had the advantage of cheap electricity, giving shafts a definite economic advantage. However, in recent years the national power utility ESKOM has undergone an expansion programme that has led to tariff increases of nearly 100% over a three-year period. Based on the changes in electricity tariffs and technological improvements to underground haulage trucks, the economic inputs to access development have changed. This paper reviews mine access for shallow deposits as currently applied in South Africa. Based on current economic inputs, the paper investigates at what point a vertical shaft would be more economical than a decline system utilizing typical South African mining equipment.

Jan 1, 2012