Search Documents

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By S. Thorley

In engineering design of operator?s compartments, in underground mining equipment, ergonomics principles are often neglected or not given the full recognition they deserve. This paper defines ergonomics, applies it to machinery in an underground mining environment and describes the ergonomics analysis undertaken during the design phase of an EJC extra-low-profile mining loader. Encompassing the design of the operator?s compartment of this new loader, this paper illustrates the importance of ergonomics principles within the collective design process, ensuring that it is fully integrated into the design approach. An ultimate aim of this study is to ensure that all future designs follow this route to guarantee not only the outcome of a highly efficient, cost-effective and productive machine but that it is also takes the human factor into account, not only in maintenance but also in operation. Maximizing comfort will have the ultimate outcome of actually increasing productivity.

Jan 1, 2006

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

By Li-ming Qi

During mining, the stress in the coal face varies, and, at the same time, the gas flows from the coal body into the excavation, which will cause the gas pressure to change continuously. Assuming the coal gas content of the coal to be constant, and applying the law of energy conservation, the influence of stress concentration on the gas pressure was analysed. It was found that the stress is proportional to the gas pressure. Finally, as a result of analysis and the law of gas flow, the gas pressure dynamic distribution ahead of tunnelling was modelled, and the mechanism by which blasting induces outburst was explained by making use of the model. Keywords: gas pressure, stress concentration, excavation, tunnel.

Jan 1, 2007

By N. Naude, W. P. Roux, O. Kaba

Ceramic filtration plates are used for dewatering slurries with high solid concentrations and particles in the size range of 30 μm to 150 μm. After extensive operating times, the ceramic filter plates at Minas Rio in Brazil begin to blind due to the precipitation of barium sulphate on the surface of the ceramic filter plate, which reduces the overall efficiency of the filtration process. Further research is needed to identify the barium precipitate phases on the blocked filter plates and its thermodynamic and kinetic behaviour in the system. A crystallography analysis was performed on the sample and the results showed that there are two different sets of precipitates formed on the filter plate: grey crystals which were large and scatted on the filter plate and red micro crystals that covered the entire surface of the filter plate. The red microcrystals on the sample were identified with XRD, which indicated that the sample contained barium sulphate in the mineral form barite. Experiments were conducted to determine the optimum conditions under which barium precipitation will occur. The conditions tested as a possible driving force for barium sulphate precipitation were the effect of temperature, pH and concentration. The pH and temperature ranges were pushed to both the lower and higher boundaries. The effect of temperatures as low as 15oC was studied and pH levels of 7 and upwards. The first nuclei started appearing at a pH of 7 but significant growth is promoted at higher pH levels. The X-Ray diffraction analysis confirmed the phase of the precipitates formed, and the orthorhombic crystallographic structure formed is a characteristic of barium sulphate. Keywords: Iron ore, barium sulphate, temperature, pH, concentration, morphology, and ceramic filter plate

Jan 1, 2020

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

By A. Dienenthal

"The casthouse floor has always been one of the most dangerous working places on a blast furnace or a ferro-alloy/nonferrous furnace. Apart from working in an atmosphere including toxic gases, fumes, and dust, the workers have to perform hard and heavy manual work close to runners and ladles filled with hot liquid metal and slag.Before the invention and installation of tapping equipment the tap-holes were opened and closed manually. Opening was done by means of steel bars and sledgehammers, whereas the tap-hole was closed by repeatedly ramming small amounts of clay or refractory material into the tap-hole, again with the help of long, heavy bars. In addition, on blast furnaces the blast had to be stopped, since it was impossible to close the tap-hole properly against the blast furnace pressure. This stoppage of the blast resulted in regular losses of production. Around 1900 a major change in technology occurred. Samuel W. Vaughen, superintendent of the blast furnace department of the Cambria Iron company at Johnstown, Pennsylvania (USA), invented the first clay gun in 1895 (Wiley, 1896) (Figure 1)."

Jan 1, 2014

By I. Ngo, L. Q. Ma, J. S. Guo

Deformation of gob-side entries has always been a critical concern for ensuring stability in longwall coal mines. This paper addresses the significant deformation and support challenges that arise in thick and hard roof longwall faces (THRLF) due to dynamic pressure. The study aims to elucidate the characteristics and mechanisms of deformation during the retreat of the longwall face. The research findings indicated that the primary cause of deformation was the combination of advanced abutment stress resulting from longwall face mining and the movement of the lateral roof over the chain pillar. To mitigate this issue, we propose a deformation control method known as cutting off the lateral roof (COLR) over the chain pillar. Simulation results demonstrate a significant reduction in roof stress and deformation of the gob-side entry after implementing the lateral roof-cutting technique. These findings provide valuable guidance for effectively managing deformation in gob-side entries, particularly when dealing with thick and hard roof strata.

Aug 3, 2023

By E. Wroth, D. G. Krige

Written contribution E. Wroth* (Visitor): The technical aspects of the assistance scheme which IS provided for in the Gold Mines Assistance Act, 1968, and certain consequential amendments to the Income Tax Act, 1962, are explained by Dr Krige. The object of this contribution is to explain the working of the Gold Mines Assistance Act (hereafter referred to as the &apos;Assistance Act&apos;) for the benefit of those concerned with the tax and assistance assessments of gold mining companies. The views expressed do not necessarily reflect the Revenue Department&apos;s interpretation of the legal provisions involved. 1. MINES WHICH QUALIFY FOR ASSISTANCE 1.1 The assistance scheme is applied on a selective basis. Mines which qualify for assistance are defined in the Assistance Act as &apos;assisted gold mines&apos;. The requirements for classification as an assisted gold mine are that: (i) the mine be a producing gold mine; (ii) it would be likely to close down within eight years if not assisted; and (iii) with State assistance its life would be appreciably prolonged and there would be a significant increase in production of gold or uranium, or of both gold and uranium. 1.2 A mine is only considered for classification as an assisted gold mine on application. Such applications must be made to the Mining Leases Board through the Government Mining Engineer. Classification of a mine as an assisted gold mine is at the discretion of the Minister of Mines who acts in consultation with the Minister of Finance and has regard to the recommendations of the Mining Leases Board. 1.3 The Minister of Mines will impose conditions subject to which a mine is to be classified as an assisted gold mine. The most important will be that the mine must immediately lower its operating pay limit, as normally calculated, by a percentage fixed by the Mining Leases Board and conduct its future mining operations in accordance with the average grade of its ore reserves determined on the basis of such lower pay limit. l.4 The Minister will fix the date as from which classification as an assisted gold mine is to be effective. So long as the mine has operated on the basis of the lowered pay limit for at least three months during the particular year of assessment, he would normally fix the effective date as the first day of the year of assessment.

Jan 5, 1968

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By G. V. R. Landman

It is self-evident that economic pressure demands that today?s mines stay ahead and stay competitive. The challenge, however, isto find fresh approaches to the pursuit of efficiency and operational effectiveness. Rather than focusing on individual activities in isolation, a process that can lead to poor investment decisions affecting other critical areas of operation, a key concept is optimization of the whole value-adding process of mining. This concept is often called ?mine to mill?. Whereas it is never easy to establish optimal conditions across a whole mining operation, the quality and consistency of the blasted rock strongly affects all operations. In many instances an inability to control rock breaking has been unchallenged, leading to significant investment in time and money to manage the consequences of poor and/or inconsistent rock breaking. This paper discusses how electronic initiation systems can play a major role in optimizing the whole mining operation. Electronically programmed detonators provide not only the ability to tightly control a key parameter, namely timing, but also the opportunity to extract blast data for a continuous improvement process. The ability to alter predictably, using feedback from the downstream processes, blasting variables such as fragmentation, throw, wall stability, and vibration, is a huge advantage. The current understanding of the effect of timing, accuracy, and scatter on rock fragmentation is reviewed and offers reasons why there is significant progress in controlling blast results. Two case studies are examined, which demonstrate the benefits of the technology on the economics of the operations under review.

Jan 1, 2010

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

By G. Cockburn

Nkomati Nickel JV exploits the ores of the Uitkomst Complex near Machadodorp in the Waterval Boven district in South Africa?s Mpumalanga Province. Due to factors such as the remote location, stellar growth in production, opencast mining methods, and ore characteristics, a number of innovative processing options were selected. Nkomati has undertaken numerous initiatives over the last few years to improve plant running times, metallurgical performance, and operational profitability. Great emphasis has been placed on effectiveness of management control systems. A number of initiatives such as short interval control and time?in-state metrics have been implemented. A focus on improvement on availability and asset utilization of key items of equipment has been particularly effective. While the ores are remarkably similar to the Merensky and UG2 reefs, the relatively high base metal sulphide content and mineralogical characteristics make metallurgical treatment somewhat different to the ores of the Bushveld Complex. The low head grades and flotation kinetics distinguish Nkomati from other base metal operations. Numerous milling and flotation optimization initiatives have resulted in dramatic improvements in throughput, recoveries, and concentrate grades. This paper discusses the metallurgical, operational, and management challenges and the outcomes obtained.

Jan 1, 2014

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005