Search Documents

By J. F. Whelan, B. D. Marshall, Z. E. Peterman, J. B. Paces, L. A. Neymark

Observations of calcite and opal in cavities in the unsaturated zone at Yucca Mountain indicate that: 1) seeps are not regularly spaced in underground workings and not all fractures sustain flow, 2) many cavities represent sites of seepage that have remained stable for millions of years, 3) typically there is no evidence (such as dripstone) for seepage dripping into cavities from their ceilings, and 4) seepage is not likely to be greater than about 1 liter of water per year (per 5-m-long drift) based on calcite abundances observed in the ESF. This estimate of seepage is significantly lower than that used for performance assessment.

Jan 1, 2000

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By C. D. Hebert, T. Gregor, M. Ghazi, G. J. E. Kramer

This paper describes the recent application of gasketed, precast concrete segmental lining design that has improved tunneling productivity and quality. The speci?c segment arrangement includes: six-piece ring with equal 60 degree gasketed segments, juxtaposed key and counter-key segments, trapezoidal and parallelogram shaped segments, inclined and skewed radial joints and plastic circumferential joint connectors. This allows rapid, but accurate ring erection, reducing mine cycle times. The design avoids cruciform joints, minimizes potential gasket damage and eliminates the need for separate left and right ring molds. The implementation on the Los Angeles ECIS and NEIS sewer projects is described.

Jan 1, 2003

By Stefan Mede

Robot Supported Moulding—this is the name of Herrenknecht Formwork’s entry to the world of automated segment production. What had been considered impossible for a long time, has been achieved by Herrenknecht experts together with the Swiss company Marti AG: unmanned segment production on the working line. The moulds open and close autonomously with the help of a hydraulic system. A robot cleans and greases the moulds at one work station and inserts the injection sockets at another. The next step will include further automation and digital networking of all processes from production to installation in the tunnel.

Jun 13, 2021

By Botond Beno, Dave Watson, Danny Read

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing I-64 four-lane bridge-tunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. The design-build contract was awarded to Hampton Roads Connector Partners with HDR and Mott MacDonald retained as lead designers in a Design Joint Venture. This paper will highlight some of the e challenges related to the design of the twin bored tunnels from spaceproong, tunnel enabling wors, segmental lining design and durability considerations.

Jun 23, 2024

By Adil Jamali, Taufiq Hidayat, Imam Santoso, Zulfiadi Zulhan, Indah Suryani

The study investigates the segregation of iron and titanium in iron sand concentrate pellets reduced using coal under an isothermal-temperature gradient profile. The results show that metallic iron migrates to the surface while titanium and other oxides move to the center of the pellet. The study provides insights into the reduction process and the behavior of iron and titanium during heat treatment.

Mar 2, 2022

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By S. Barkhoudarian, R. R. Gupta, R. F. Steinberg

A study of the feasibility of using acoustic signals to detect discontinuities ahead of excavation has shown that reflecting interfaces in a homogeneous rock can be easily identified. Moreover, discontinuity interfaces in a very complex field site (where the rock face was weathered, was full of jointed rocks, and had a destressed zone running along the mine walls) could be identified with a reasonable level of confidence, using a cross-correlation technique for signal processing. The results of this study go a long way toward proving the feasibility of the technique. However, further development work is needed to optimize an operating system in a hard rock environment where boring machines are used for excavation.

Jan 1, 1997

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By Preusse. Axel

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By J. W. Cooksley

Pyrometasomatic zones are a type of replacement deposit, normally in a carbonate rock unit, which consists of a zoned, coarse-grained, generally iron-rich mixture of calcium and magnesium silicates. These zones or rock masses are also called ?skarn,? and ?tactite?. They are formed as a result of the interaction of a shallow intrusion of magma with a carbonate or calcareous host rock and are considered to be of hydrothermal origin. Three environments of pyrometasomatic deposits are depicted in Figure 1. Of course, the interaction takes place at high temperatures. Pyrometasomatic zones are categorized as calcic or magnesian, depending on whether the intrusive interacts with a limestone or a dolomite. Common pyrometasomatic zone minerals are garnet, epidote, quartz, calcite, wollastonite, actinolite, hedenbergite and diopside. Pyrometasomatic zones are of considerable economic importance because they contain ore deposits of tungsten, molybdenum, copper, lead, zinc and iron. According to Rose and Burt (1979), the chronological sequence in the formation of a ?typical? pyrometasomatic deposit is as follows: 1. Shallow intrusion of magma at 900-700°C into carbonate sediments.

Jan 1, 1981