Search Documents

By M. B. Mooiman

It has recently been discovered that the pH at which gold can be extracted from cyanide solution with primary, secondary, and tertiary amines can be increased 2 to 5 pH units by the addition of modifiers. Under these circumstances gold can be extracted at pH values from 9 to 11, commensurate with the pH range found in cyanide leach liquors. The selectivity of the amines and amine/modifier combinations for AU (CN)[-2] over other metal -cyanide complexes is presented and discussed. In addition, potential applications for the solvent extraction of gold from cyanide solutions are discussed.

Jan 1, 1983

By Phil Pennington, D. Jack Adams

Mining and processing of minerals, metals, and fossil fuels can release selenium and arsenic into wastewaters. Both selenium and arsenic are difficult to remove to levels that meet current drinking water and discharge criteria. These metalloids can be used as electron acceptors by microorganisms transforming them back to reduced states, thus removing or stabilizing them. Bioremediation cost effectiveness will be discussed in terms of site information required, microbial populations, co-contaminants, pH, redox, and nutrients. Full-scale, economical ex situ and in situ biotreatments are possible and can produce 1,000’s of times less sludge than conventional precipitation technologies.

Jan 1, 2005

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By Paul D. Chamberlin

In the author's selenium report of 1994 (1), the literature was culled for selenium removal technologies that had a chance of producing effluents with <10 ppb of total selenium. Very few processes could achieve such low concentrations. The EPA dictates such low concentrations. Discharges to fishery waters must be <5 ppb total selenium. The federal max­imum contaminant level ( MCL) for drinking water is 50 ppb. The EPA regulations are for total selenium, not for the species, perhaps because an approved EPA assay method is atomic absorption and it cannot distinguish between species.

Jan 1, 1996

By Kathleen A. Altman, Kevin Hegerle

FMC Gold Company start.ea processing ore at their Paradise Peak Mine in 1986. Gold, silver and mercury haye been produced from the Merrill-Crowe milling circuit and from heap leaching. There are three heap leach circuits, Paradise Peak, Ketchup Flat and County Line. The Paradise Peak and Ketchup Flat heap effluent solutions are routed into the zinc precipitation plant which is associated with the mill for recovery of the precious metals. The County Lne hea lech circuit is a stand-alone operation, again with a zinc precipitation recovery circuit. The mill was shut down in May, 1993 due to depletion of ore reserves with the remainder of the heap leach ore due to be placed on the leach pads by late summer of the same year.

Jan 1, 1993

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure&apos;acid leaching.

Jan 1, 2002

By John H. Archibald, Arthur L. Miller, George A. Savanick

As part of its continuing research on selective mining, the Bureau of Mines has made progress toward developing a tool capable of remotely extracting hard minerals through a borehole. As the successor to the successful borehole miner, which extracted soft materials through a straight borehole, this new device has several innovative features: 1) it can propel itself in and out of an 8-inch borehole; 2) it can cut hard rock with an abrasive jet and transport the cuttings to the surface; and 3) it can negotiate deviated boreholes--the feature that enables it to follow a vein and extract only the values. This paper describes the development and feature testing of the reamer/miner.

Jan 1, 1991

By M. Makarenko

The sandstone type Devladivske uranium deposit is located within the limits of Eocene pale-ovalley filled with alluvial sediments. Mineralization with uranium content up to 0.1% forms several ore beds divided by redox barriers. In the period 1962-1983 the deposit has been exploited over an area of 918000m2 by in situ leaching (ISL) using drillholes with a depth between 35 and 100m. During mining operation about 200,000 t of H2SO4, 6,300 t of HNO3, and 15,000 t of NH4NO3, have been pumped in the ore body. In 1983, the groundwater pollution aureole had a length of 4.5 km and a width of 400-600 m. There is a hydraulic connection between the uranium-bearing aquifer and both the upper and lower ones. The technological solutions used for ISL caused partial contamination of these horizons. After mining completion, dilution of the residual technological solutions with "pure" natural waters took place through gaps in impermeable sediments between aquifer horizons. Calculation of self-purification process kinetics shows that the sulfate ion pollution aureole will disappear approximately after 120-150 years at a distance up to 2.0-2.5 km from the western margin of the deposit. This means that there is no risk for contamination of the river Saksagan? that flows at a distance of 17km from the deposit.

Jan 1, 2005

By Rodolfo V. de la Cruz

This paper describes the development of a new method and device for determining the in-situ mechanical properties of rock masses. The method involves a self-recording mechanical deformation gauge for sensing-recording she deformation of the borehole wall when loaded hydraulically. The self-recording feature of the gauge eliminates the difficult technical problem of transmitting signals over very long cables for measurements at great depths. Adopting a mechanical gauge instead of electronic, electrical, optical or grid techniques eliminates delicate instrumentation and installation problems. Moreover, mechanical gauges are inherently rugged and suitable for use in severe borehole conditions including very high temperatures. The technique was tested in limestone, basalt and granite specimen. The calculated mechanical property values for 1 the tests agree with those obtained by conventional testing methods. The self-recording mechanical deformation gauge has a minimum reading of 50 micro inches (1.27 x 10-3mm), comparable with electrical resistance strain gauges, capable of reading deformations over a range of 0.25 inches (6.35mm). The sensitivity, ease and accuracy of the method recommends it highly for in-situ rock modulus measurements.

Jan 1, 1980

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By Thomas D. Kaufmann

Whether pursuing hedging or speculative strategies, gold miners can increase sales revenues 1 % to 6% by constantly pricing production forward. Unlike other commodities, gold futures prices are consistently higher than spot prices. A Colorado School of Mines study showed theoretically and empirically that in the 15 years since the price of gold was released from government control, the forward price for gold has been higher than the current price almost 100% of the time. The reason why Metal traders know that holders of metal earn a bonus selling forward when the metal is in "contango." "Contango" is a mysterious word that crept into the trading vocabulary a century ago. It designates a situation when the price of a metal on the futures markets is higher than the price in the immediate or spot market. If the spectrum of spot and futures prices remains static over time, the forward seller who has contracted at a higher than spot price can make a profit equal to the contango by redeeming his commitment at the lower spot price when the contract matures. Consequently, when a seller in a contango market hedges, he makes a profit on the transaction in addition to avoiding a price change risk. On the other hand, buyers of the metal who hedge in a contango situation will sustain a loss equal to the contango. Producers of gold, however, are sellers of gold. For most metals and oil, there is no inherent reason why futures prices should be higher than present prices. Buyers and sellers decide that the price of the commodity will be lower or higher than present values for a variety of reasons.

Jan 1, 1991

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO&apos;s Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By N. J. Themelis

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early thirties in the so-called Hadsel mills (Figure 1) mainly used in gold mines on the U.S. West Coast. A number of these mills were built in sizes of 20 to 24 ft. in diameter and five-six feet in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill (Figure 2), the Aerofall dry grinding mill and others. A tabulation of all known autogenous and semi-autogenous installations around the world was sent recently to the authors by Hr. G. J. Kushner of the Koppers Mineral Processing Division. In the size range of 24 to 32-ft. in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 36-ft. dia X 15-ft. long mills in Minnesota, powered by 12,000 hp. motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above one hundred and fifty mills was in operation prior to 1964.

Jan 1, 1978

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By David M. Kjos

Large diameter autogenous and semi-autogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semi-autogenous mills have reached an acceptable level of technology which provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant it is to be installed in. This is particularly true in autogenous and semi-autogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only ?paper.? Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs and operating practices, and provide some guidelines for good practice as we move through the 1980&apos;s. We will put together concepts that relate to the designs, materials and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series because they are dependent on each other to achieve the desired performance.

Jan 1, 1985