Search Documents

By T. C. Rao, D. D. Patil

The fishhook effect, wherein the recovery of fine particles in the underflow increases with decreasing particle size, has been observed in hydrocyclone classification. A systematic study was carried out to determine the factors affecting the recovery of very fine particles to the underflow. Attempts were made to identify factors, i.e., design and operating variables, that affect the size at which this phenomenon occurs. Experimental results show that the sizes at which the fishhook effect occurs is mainly a function of feed size distribution and solids concentration and is less dependent on the design variables.

Jan 1, 2002

By D. Hongjun

In this paper, the flotation rule and behaviors of kyanite-group polymerphous minerals were studied in modified Hallimond tube in detail. Furthermore, the energy change of collector/mineral systems before and after adsorption and the net charge densities of the atoms on the minerals surfaces were calculated by use of quantum chemistry. The flotabilities in minerals were successfully explained.

Jan 1, 1995

By Maurício L. Torem, Isabella A. Scorzelli

Taboca Mining is one of the largest producers of tin in the world. In its pilot plant, significant amounts of a middling of 90% xenotime (YPO4) and 10% zircon (ZrSi04) are produced. Until now, these minerals of this ore body could not be separated successfully. This paper presents some aspects of the fundamentals of xenotime and zircon flotation with anionic (fatty acids) and cationic (amine acetate) collector, as well as the influence of the superficial leaching of the minerals with cold HCI and HNO3 on the floatability. The mineralogical studies showed that both minerals are optically liberated in -212+106 µm size fraction. Surprisingly, SEM analysis indicated that both xenotime and zircon contain very small inclusions (1-5 µm) of thorite (ThSiO4). On the other hand, zircon is fairly metamictizated giving rise to malacon. Zeta potential tests showed that the isoelectric points of xenotime and zircon correspond to a pH value of 4.5 and 4.7, respectively.The pretreatment with HCI and HNO3 displaced the isoeletric point (IEP) of the minerals to the left. The microflotation tests indicated that the floatability of both untreated and treated minerals are quite similar in the presence of the collectors studied in this work. Adsorption mechanisms are also suggested.

Jan 1, 1995

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Ruoming Gong, Arindam Samanta, Ragula Bhaskar

Three studies conducted at the University of Utah relating to the effect of scrubbers on face airflow patterns, the resulting dust exposure of operators and the development of a throat scrubber for continuous miners are summarized in this paper. The first study involved full-scale laboratory tests to determine the potential dispersion patterns and transport of dust at a continuous miner face, using different ventilation configurations and a scrubber. Concentration maps were developed and potential exposures at operator positions were examined. The second study involved the development of a 3-D numerical model to predict airflow patterns generated by a scrubber at a continuous miner face. The model was designed to evaluate the role of various face parameters on airflow patterns at a miner face and to complement the full-scale testing. The third study involved the design and fabrication of a low profile hydraulically powered continuous miner throat scrubber. The scrubber uses three hydraulic motors and small diameter fans to draw about 3000 cfm (1.42 m3/s) of air and uses a flooded bed scrubber to filter dust particles.

Jan 1, 1993

By R. A. Jankowski, R. Gong, R. Bhaskar

The control of respirable coal dust in continuous mining sections involves careful analyses of the generation and transport of the dust, including airflow pattern analyses. Potential dust control devices must be evaluated based on their effect on both local dust transport and potential dust exposure of face personnel. The development of larger and more productive continuous miners increases the need for research on dust control and improvement of visibility in the face area. Two studies relating to underboom dust control are discussed. The first study involved the valuation of potential underboom dust control techniques to reduce operator exposure to dust and determining the relationship between the positioning of exhaust ventilation and the exposure of face personnel as a function of face and operating variables. The study involved full-scale laboratory experiments using a state- of-the-art data acquisition system. The second study related to the use of foam under a continuous miner boom and its effect on silica concentration and respirable dust. The foam study was performed in a coal mine. The laboratory studies involved the fabrication of a full-scale test facility and development of a computer based data acquisition system. This was followed by baseline data collection, smoke trace tests, detailed performance testing of various underboom dust control measures and data analyses. The underground foam test involved the design and installation of the foam generation and delivery system, testing, and data evaluation. The results of the studies are summarized in this paper.

Jan 1, 1991

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By B. Lin, C. Tang, Z. Chen

Earthquakes, underground impact pressures and rock bursts all produce acoustic emissions. The rate of these emissions can be used to describe rock instability. In this study, it was found that acoustic-emission rates obtained by simulating a twin sample (rock-rock) model could be used to indicate the acoustic-emission-rate characteristics during rock instability. A computer simulation and two case studies support this conclusion.

Jan 1, 1997

By Sundar S. Saluja

Efficient and re1iable methods of fragmentation through blasting have been sought ever since the introduction of black powder in mining operations, but the pace of investigation became faster with the discovery of nitroglycerine. The development of modern measuring instruments and the need to blast more rock with the least damage has made the study of blasting mechanics and its application more important, particularly since the oil embargo. Investigations into the practical approach evolved by Daws (1909) and the work done to make it more useful is discussed. The work of several investigators is touched upon with particular reference to the development of computer programs to simulate and optimize blasting operations.

Jan 1, 1986

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By S. Siddiqua

Diffusion is known to be the main transport mechanism of contaminants in fine-gained soils. To date, it is still common practice to estimate contaminant migration in the Bangkok Clay by means of pure advection models. A series of experiments with various chemical species was performed to determine transport parameters such as the diffusion coefficients and the distribution coefficients. The soil used was saturated undisturbed Soft Bangkok Clay. Column experiments were utilized in a number of laboratory tests involving advective-diffusive migration. Effective diffusion coefficients of different ions were back calculated from the test results. The distribution coefficients were determined from the results of the column tests and batch test. The results indicate that the evaluated parameters are in the range of values obtained from other researchers on similar kinds of soil. Based on this results contaminant migration by diffusion in the Soft Bangkok Clay can now be performed.

Jan 1, 2005

By Qingxia Liu, Chen Tingzhong, Chen Jin, Yang Xiaosheng

It is common problem (Huan Xinsheng, etc.,l992)for most iron ore concentrators in China that the concentration of thickened tailings is lower than the need for economical transportation. To solve the problem, two methods of improving the properties of the existing thickeners and using separate thickening technique have been applied in three iron ore concentrators. However, in the case of the Daye iron concentrator a new technique of cyclone-flocculated sedimentation was developed by present authors and verified by experiments. The new technique employs efficient hydrocydone designed by authors in conjunction with a low cost flocculant named KLP.

Jan 1, 1995

By Gregory E. Tieman

Hydrologic impacts of longwall mining were studied in 1986 after mining had occurred at mine "Z" in northern West Virginia. This mine is 700 to 1,300 ft deep, with a surface topographic relief of 300 to 500 ft. Five springs and one dug well were reportedly dewatered by mining. All such supplies are above nearby streams in elevation, and at least 800 ft above the subsided mine. Three of these six supplies showed partial recovery within one year. Only supplies within 50 ft in elevation of a nearby stream showed apparent partial recovery. Measured perennial streams showed notable depletion in streamflow over mined longwall panels that were less than two years old. Normal stream discharge was measured over panels more than two years old. Most apparent hydrologic dewatering impacts appear to be temporary, and the most vulnerable areas for these impacts are hill sides.

Jan 1, 1986

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By D. R. Bomberger

An automatic microscope has been developed to .measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed.

Jan 1, 1963