Search Documents

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By Peter Bryant

"The case for innovation in the mining industry has never been more compelling—whether you believe the industry is in a sharp dip in a significant ‘sawtooth’ cycle or in the midst of a bust — the imperative is the same. Despite record production levels and still above-average prices compared to the lows of 2000, the industry is struggling to make profits and provide the returns on capital that investors are seeking. This represents a large-scale destruction of value over the last 15 years.The last 10 years have seen a sustained rise of operation expenses and capital development costs while there has been a rapid decline in productivity. This trend is unsustainable especially against other key structural challenges and forces shaping the future of the industry:1. Despite short-term fluctuations, there is longterm sustained demand for commodities.• Demand is driven by relentless urbanization, population growth and a rapidly growing middle class.2. Environmental concerns continue to mount.• Existing mining methods and their environmental footprint are becoming increasingly unacceptable to society.3. Geopolitical pressures and community activism are growing.• An estimated $25 billion worth of projects are on hold due to community activism.• Increasing nationalism tendencies and government expropriations of close to $30 billion.• Social license to operate is being challenged.4. Finding, building, operating and closing a mine just keeps getting harder and more expensive.• Costs have been increasing at an annual rate of 10 to 15 percent for the last 10 years.• More assets are stranded as they become uneconomical to mine under current mining methods, e.g. Olympic Dam.• Ore grades continue to decline.• Declining productivity at an annual rate of more than 10 percent for the last 10 years.5. The industry has consistently underinvested in technology and innovation."

Jan 1, 2015

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By J. A. Cole

This paper discusses the modification of the cyanide tailings treatment method from ferrous sulfate to Caro's acid (peroxymonosulfuric acid). An examination of the operating parameters, costs, and chemistry describes how the decision was made to switch to this treatment method. Plant data collected from the last several months will be used, along with considerations from an operator's viewpoint.

Jan 1, 1996

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By Leonard Harris, Rosa H. Harris

An important part of doing business today in the mining industry, especially overseas, involves community assistance programs for the people who live around the mining areas. The purpose of such a program is to build mutual cooperation and respect that will allow the company and its neighbors to live and work in peace. To do this, it is necessary to form associations or foundations and work in a joint venture fashion. The authors discuss in some detail the outline for setting up such programs and the important role that women, in particular, can play in them.

Jan 1, 2001

By J. E. Gebhardt, J. A. Herbst, K. Y. Lee

Benefits of proper control of reagent usage in flotation circuits are typically improved metallurgy and savings in reagent costs. Improved metallurgy can mean more consistent product quality, i.e., final concentrate grade, better recovery of product values from the feed, or higher plant throughput at existing target recovery, and grade values. Flotation performance is sensitive to a variety of process disturbances which occur in operating plants, such as changes in flow rate, percent solids, size distribution. flotability of mineral species, etc. A way to handle these variations is to fully understand the dynamic flotation responses to disturbances and to implement a suitable control strategy to compensate for these disturbances. Depending on the objectives of the control system, various types of control strategies are available which employ different levels of refinement to achieve the desired performance. Typically, variables such as collector and frother dosages and reagent addition points can be manipulated to affect the performance of the circuit. In the case of sulflde mineral flotation, manipulation of the process electrochemical potential, in flotation and in grinding, offers another degree of process control. Because of the complex and interactive nature of flotation process variables, optimized reagent control requires consideration of all, or at least the most important, interactive variables of the flotation circuit. Model- based optimizing control provides a framework to handle the complex and dynamic nature of flotation reagent process control.

Jan 1, 1994

By N. Powell, C. F. Spollen, B. A. Wills

A discussion of the practicalities of carrying out a material balance using simple nodal sensitivity analysis is given. The calculation of the errors involved is reviewed and the concept of co-variance examined through computer simulation. The use of co-variances in such calculations is shown to be practically insignificant. The method proves to be rapid and relatively accurate provided the circuit topology is correct.

Jan 1, 1991

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012

Marble has been recognized as a valuable natural resource ever since ancient times. Due to its peculiar aesthetic and technical characteristics as well as the lithotype uniqueness, it has widely been appreciated over the past centuries. In present times its production and demand are enjoying an increasing trend, with comparatively high market prices. All this considered, marble can be included among these natural resources whose exploitation provided, and still provides, an important contribution to the growth of the economic system. Nevertheless, there is at least one more important reason that makes marble a valued resource. For ages, marble represented one of the most important raw materials for sculpture sand architectural masterpieces, which constitute part of the cultural heritage of mankind. With this in mind, the value of marble is strictly related to its extraordinary capability to preserve cultural heritage and therefore to convey civilization from past to future generations. In other words, the role of marble should be recognized as being of the utmost importance in order to attain an overall objective of ?cultural sustainability?, that is, the assurance of the inter-generational flow of the cultural heritage capital. To achieve this sustainability goal, the priorities should be to protect and preserve the world?s artistic and architectural historical heritage, which require restoration works. In this field, a very il task is entrusted to the extractive industry: this industry, in cooperation with historians, art experts and public authorities, is in charge of detecting and supplying historical stones for restoration purposes, taking into consideration that, in order to restore a monument in a correct way, the same lithotypes the monument was made from are needed. These marbles are often no longer in production, so that it becomes necessary to find the location of the original quarries, as only there is it possible to extract even the small quantities of stones that are needed. In this case, the stone, located in its geological context, could have such valued characteristics as to be considered an important public asset and consequently a resource to be preserved and protected even beyond the market conditions. This important task should be carried out by the public administration through a targeted intervention of territorial planning and monitoring, which could include the support for the specific extractive activity.

Jan 1, 2003

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968